Lines Matching +full:super +full:- +full:speed
7 Addresses scanned: from Super I/O config space (8 I/O ports)
11 Addresses scanned: from Super I/O config space (8 I/O ports)
14 Addresses scanned: from Super I/O config space (8 I/O ports)
18 Addresses scanned: from Super I/O config space (8 I/O ports)
22 Addresses scanned: from Super I/O config space (8 I/O ports)
26 Addresses scanned: from Super I/O config space (8 I/O ports)
30 Addresses scanned: from Super I/O config space (8 I/O ports)
34 Addresses scanned: from Super I/O config space (8 I/O ports)
38 Addresses scanned: from Super I/O config space (8 I/O ports)
42 Addresses scanned: from Super I/O config space (8 I/O ports)
46 Addresses scanned: from Super I/O config space (8 I/O ports)
50 Addresses scanned: from Super I/O config space (8 I/O ports)
54 Addresses scanned: from Super I/O config space (8 I/O ports)
58 Addresses scanned: from Super I/O config space (8 I/O ports)
62 Addresses scanned: from Super I/O config space (8 I/O ports)
66 Addresses scanned: from Super I/O config space (8 I/O ports)
70 Addresses scanned: from Super I/O config space (8 I/O ports)
74 Addresses scanned: from Super I/O config space (8 I/O ports)
78 Addresses scanned: from Super I/O config space (8 I/O ports)
87 -----------------
102 misconfigured by BIOS - PWM values would be inverted. This option tries
107 -------------------
109 All the chips supported by this driver are LPC Super-I/O chips, accessed
110 through the LPC bus (ISA-like I/O ports). The IT8712F additionally has an
118 -----------
125 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
128 rotation speed sensors, 8 voltage sensors, associated alarms, and chassis
137 is stored in the Super-I/O configuration space. Due to technical limitations,
148 IT8783E/F, and late IT8712F and IT8705F also have optional 16-bit tachometer
150 not compatible with the older chips and revisions. The 16-bit tachometer mode
161 IT8728F. It only supports 3 fans, 16-bit fan mode, and the full speed mode
165 to IT8728F. It only supports 16-bit fan mode. Both chips support up to 6 fans.
167 The IT8790E supports up to 3 fans. 16-bit fan mode is always enabled.
169 The IT8732F supports a closed-loop mode for fan control, but this is not
176 triggered if the rotation speed has dropped below a programmable limit. When
177 16-bit tachometer counters aren't used, fan readings can be divided by
199 The driver handles this transparently so user-space doesn't have to care.
210 once-only alarms.
212 Out-of-limit readings can also result in beeping, if the chip is properly
226 Fan speed control
227 -----------------
229 The fan speed control features are limited to manual PWM mode. Automatic
234 If you are only able to control the fan speed with very small PWM values,
238 read-only.
241 Automatic fan speed control (old interface)
242 -------------------------------------------
244 The driver supports the old interface to automatic fan speed control
250 at full speed) while the PWM output of the other 3 trip points can be
262 Trip points must be set properly before switching to automatic fan speed
268 -----------------------------
270 The driver supports temp[1-3]_offset sysfs attributes to adjust the reported
271 temperature for thermal diodes or diode-connected thermal transistors.