Lines Matching +full:1 +full:- +full:based
3 ----
24 1.2.1 Driver Name
30 2.1 CS8900-based Adapter Configuration
31 2.2 CS8920-based Adapter Configuration
43 5.2.1 Diagnostic Self-Test
62 The CS8900-based ISA Ethernet Adapters from Cirrus Logic follow
63 IEEE 802.3 standards and support half or full-duplex operation in ISA bus
65 in 16-bit ISA or EISA bus expansion slots and are available in
66 10BaseT-only or 3-media configurations (10BaseT, 10Base2, and AUI for 10Base-5
69 CS8920-based adapters are similar to the CS8900-based adapter with additional
80 or loaded at run-time as a device driver module.
82 1.2.1 Driver Name: cs89x0
88 readme.txt - this file
89 build - batch file to compile cs89x0.c.
90 cs89x0.c - driver C code
91 cs89x0.h - driver header file
92 cs89x0.o - pre-compiled module (for v2.2.5 kernel)
93 config/Config.in - sample file to include cs89x0 driver in the kernel.
94 config/Makefile - sample file to include cs89x0 driver in the kernel.
95 config/Space.c - sample file to include cs89x0 driver in the kernel.
103 * Cirrus Logic LAN (CS8900/20-based) Ethernet ISA Adapter
105 * IBM or IBM-compatible PC with:
107 * 16 bytes of contiguous IO space available between 210h - 370h
108 * One available IRQ (5,10,11,or 12 for the CS8900, 3-7,9-15 for CS8920).
110 * Appropriate cable (and connector for AUI, 10BASE-2) for your network
117 * CS8900/20 Setup Utility (DOS-based)
130 Foundation, version 1.
145 Both the CS8900 and CS8920-based adapters can be configured using parameters
146 stored in an on-board EEPROM. You must use the DOS-based CS8900/20 Setup
150 configuration parameters on the command-line to override the EEPROM's settings
151 or for interface configuration when an EEPROM is not used. (CS8920-based
154 Since the CS8900/20 Setup Utility is a DOS-based application, you must install
155 and configure the adapter in a DOS-based system using the CS8900/20 Setup
157 installing a CS8900-based adapter and the default configuration is acceptable.)
160 2.1 CS8900-BASED ADAPTER CONFIGURATION
162 CS8900-based adapters shipped from Cirrus Logic have been configured
170 Transmission Mode: Half-duplex
172 Media Type: Autodetect (3-media cards) or
173 10BASE-T (10BASE-T only adapter)
180 2.2 CS8920-BASED ADAPTER CONFIGURATION
182 CS8920-based adapters are shipped from Cirrus Logic configured as Plug
184 support PnP, you must install the CS8920 adapter in a DOS-based PC and
192 * CS8920-BASED ADAPTERS: *
194 * CS8920-BASED ADAPTERS ARE PLUG and PLAY ENABLED BY DEFAULT. *
208 be specified as command-line arguments to the load command. This facility
220 * io=### - specify IO address (200h-360h)
221 * irq=## - specify interrupt level
222 * use_dma=1 - Enable DMA
223 * dma=# - specify dma channel (Driver is compiled to support
225 * dmasize=# (16 or 64) - DMA size 16K or 64K. Default value is set to 16.
226 * media=rj45 - specify media type
230 * duplex=full - specify forced half/full/autonegotiate duplex
233 * debug=# - debug level (only available if the driver was compiled
238 a) If an EEPROM is present, any specified command-line parameter
242 b) The "io" parameter must be specified on the command-line.
259 e) The minimum command-line configuration required if an EEPROM is
267 used with no EEPROM or command-line argument).
272 * CS8900 defaults to half-duplex if not specified on command-line
273 * CS8920 defaults to autoneg if not specified on command-line
290 options cs89x0 io=0x0200 dma=5 use_dma=1
303 with large ping packets consumes 82% of its CPU capacity in non-DMA
306 k) If your Linux kernel was compiled with inbuilt plug-and-play
316 (non-modular) then its I/O address is automatically determined by
330 image=/boot/bzImage-2.3.48
334 read-only
352 "gcc -D__KERNEL__ -I/usr/src/linux/include -I/usr/src/linux/net/inet -Wall
353 -Wstrict-prototypes -O2 -fomit-frame-pointer -DMODULE -DCONFIG_MODVERSIONS
354 -c cs89x0.c"
362 The compile-time optionality for DMA was removed in the 2.3 kernel
364 enabled by the 'use_dma=1' module option.
384 CS8900/20-based adapter card (it must also be running the CS8900/20 Setup
388 DOS-only operating system environment. DO NOT run the diagnostics
394 1.) Boot DOS on the PC and start the CS8900/20 Setup Utility.
399 4.) Select 'Diagnostics' (ALT-G) from the main menu.
400 * Select 'Self-Test' to test the adapter's basic functionality.
404 5.2.1 DIAGNOSTIC SELF-TEST
406 The diagnostic self-test checks the adapter's basic functionality as well as
407 its ability to communicate across the ISA bus based on the system resources
430 * Internal Loop-back Test
456 This test requires that each of the two PCs have a CS8900/20-based adapter
469 1.) Select a PC with a CS8900/20-based adapter and a known working network
471 and select 'Diagnostics -> Network Test -> Responder' from the main
474 2.) Return to the PC with the CS8900/20-based adapter you want to test and
477 3.) From the main menu, Select 'Diagnostic -> Network Test -> Initiator'.
489 The 2 and 3-media adapters have two LEDs visible on the back end of the board
490 located near the 10Base-T connector.
492 Link Integrity LED: A "steady" ON of the green LED indicates a valid 10Base-T
493 connection. (Only applies to 10Base-T. The green LED has no significance for
494 a 10Base-2 or AUI connection.)
504 of four ways after installing and or configuring the CS8900/20-based adapter:
506 1.) The system does not boot properly (or at all).
518 diagnostic self-test. Normally, the ISA resource in conflict will fail the
519 self-test. If so, reconfigure the adapter selecting another choice for the
526 diagnostics self-test to ensure the new configuration is free of conflicts
533 ----------- -------- --- --------
534 200-20F Game I/O adapter 3 COM2, Bus Mouse
535 230-23F Bus Mouse 4 COM1
536 270-27F LPT3: third parallel port 5 LPT2
537 2F0-2FF COM2: second serial port 6 Floppy Disk controller
538 320-32F Fixed disk controller 7 LPT1
539 8 Real-time Clock
543 -------------- --------------------- 14 Hard Disk controller
544 A000-BFFF EGA Graphics Adapter
545 A000-C7FF VGA Graphics Adapter
546 B000-BFFF Mono Graphics Adapter
547 B800-BFFF Color Graphics Adapter
548 E000-FFFF AT BIOS
560 Telephone :(800) 888-5016 (from inside U.S. and Canada)
561 :(512) 442-7555 (from outside the U.S. and Canada)
562 Fax :(512) 912-3871
572 1.) Adapter type (CRD8900, CDB8900, CDB8920, etc.)
577 * Plug and Play enabled/disabled (CS8920-based adapters only)
578 * Configured for media auto-detect or specific media type (which type).
605 software-update notification.