Lines Matching +full:backlight +full:- +full:gpios
2 * at91sam9n12ek.dts - Device Tree file for AT91SAM9N12-EK board
9 /dts-v1/;
13 model = "Atmel AT91SAM9N12-EK";
18 stdout-path = "serial0:115200n8";
27 clock-frequency = <32768>;
31 clock-frequency = <16000000>;
47 compatible = "atmel,tcb-timer";
52 compatible = "atmel,tcb-timer";
64 clock-names = "mclk";
70 interrupt-parent = <&pioA>;
72 pinctrl-names = "default";
73 pinctrl-0 = <&pinctrl_qt1070_irq>;
78 pinctrl-0 = <
85 bus-width = <4>;
86 cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>;
92 pinctrl_board_mmc0: mmc0-board {
122 cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
125 spi-max-frequency = <50000000>;
133 hlcdc-display-controller {
134 pinctrl-names = "default";
135 pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
140 remote-endpoint = <&panel_input>;
147 pinctrl-names = "default";
148 pinctrl-0 = <&pinctrl_usb1_vbus_sense>;
149 atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
165 nand_controller: nand-controller {
167 pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
168 pinctrl-names = "default";
172 rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
173 cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
174 nand-bus-width = <8>;
175 nand-ecc-mode = "soft";
176 nand-ecc-strength = <2>;
177 nand-ecc-step-size = <512>;
178 nand-on-flash-bbt;
185 num-ports = <1>;
186 atmel,vbus-gpio = <&pioB 7 GPIO_ACTIVE_LOW>;
191 backlight: backlight { label
192 compatible = "pwm-backlight";
194 brightness-levels = <0 4 8 16 32 64 128 255>;
195 default-brightness-level = <6>;
196 power-supply = <&bl_reg>;
201 compatible = "regulator-fixed";
202 regulator-name = "backlight-power-supply";
203 regulator-min-microvolt = <5000000>;
204 regulator-max-microvolt = <5000000>;
209 compatible = "gpio-leds";
213 gpios = <&pioB 4 GPIO_ACTIVE_LOW>;
214 linux,default-trigger = "mmc0";
219 gpios = <&pioB 5 GPIO_ACTIVE_LOW>;
220 linux,default-trigger = "nand-disk";
225 gpios = <&pioB 6 GPIO_ACTIVE_HIGH>;
226 linux,default-trigger = "heartbeat";
231 compatible = "gpio-keys";
235 gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
237 wakeup-source;
242 compatible = "qiaodian,qd43003c0-40", "simple-panel";
243 backlight = <&backlight>;
244 power-supply = <&panel_reg>;
245 #address-cells = <1>;
246 #size-cells = <0>;
251 #address-cells = <1>;
252 #size-cells = <0>;
256 remote-endpoint = <&hlcdc_panel_output>;
262 compatible = "regulator-fixed";
263 regulator-name = "panel-power-supply";
264 regulator-min-microvolt = <3300000>;
265 regulator-max-microvolt = <3300000>;
270 compatible = "atmel,asoc-wm8904";
271 pinctrl-names = "default";
272 pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
275 atmel,audio-routing =
283 atmel,ssc-controller = <&ssc0>;
284 atmel,audio-codec = <&wm8904>;