1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Configuation settings for the Freescale MCF54455 EVB board. 4 * 5 * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. 6 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 7 */ 8 9 /* 10 * board/config.h - configuration options, board specific 11 */ 12 13 #ifndef _M54455EVB_H 14 #define _M54455EVB_H 15 16 /* 17 * High Level Configuration Options 18 * (easy to change) 19 */ 20 #define CONFIG_M54455EVB /* M54455EVB board */ 21 22 #define CONFIG_MCFUART 23 #define CONFIG_SYS_UART_PORT (0) 24 25 #define LDS_BOARD_TEXT board/freescale/m54455evb/sbf_dram_init.o (.text*) 26 27 #undef CONFIG_WATCHDOG 28 29 #define CONFIG_TIMESTAMP /* Print image info with timestamp */ 30 31 /* 32 * BOOTP options 33 */ 34 #define CONFIG_BOOTP_BOOTFILESIZE 35 36 /* Network configuration */ 37 #define CONFIG_MCFFEC 38 #ifdef CONFIG_MCFFEC 39 # define CONFIG_MII_INIT 1 40 # define CONFIG_SYS_DISCOVER_PHY 41 # define CONFIG_SYS_RX_ETH_BUFFER 8 42 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 43 44 # define CONFIG_SYS_FEC0_PINMUX 0 45 # define CONFIG_SYS_FEC1_PINMUX 0 46 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 47 # define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_IOBASE 48 # define MCFFEC_TOUT_LOOP 50000 49 # define CONFIG_HAS_ETH1 50 51 # define CONFIG_ETHPRIME "FEC0" 52 # define CONFIG_IPADDR 192.162.1.2 53 # define CONFIG_NETMASK 255.255.255.0 54 # define CONFIG_SERVERIP 192.162.1.1 55 # define CONFIG_GATEWAYIP 192.162.1.1 56 57 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 58 # ifndef CONFIG_SYS_DISCOVER_PHY 59 # define FECDUPLEX FULL 60 # define FECSPEED _100BASET 61 # else 62 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 63 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 64 # endif 65 # endif /* CONFIG_SYS_DISCOVER_PHY */ 66 #endif 67 68 #define CONFIG_HOSTNAME "M54455EVB" 69 #ifdef CONFIG_SYS_STMICRO_BOOT 70 /* ST Micro serial flash */ 71 #define CONFIG_SYS_LOAD_ADDR2 0x40010013 72 #define CONFIG_EXTRA_ENV_SETTINGS \ 73 "netdev=eth0\0" \ 74 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 75 "loadaddr=0x40010000\0" \ 76 "sbfhdr=sbfhdr.bin\0" \ 77 "uboot=u-boot.bin\0" \ 78 "load=tftp ${loadaddr} ${sbfhdr};" \ 79 "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \ 80 "upd=run load; run prog\0" \ 81 "prog=sf probe 0:1 1000000 3;" \ 82 "sf erase 0 30000;" \ 83 "sf write ${loadaddr} 0 0x30000;" \ 84 "save\0" \ 85 "" 86 #else 87 /* Atmel and Intel */ 88 #ifdef CONFIG_SYS_ATMEL_BOOT 89 # define CONFIG_SYS_UBOOT_END 0x0403FFFF 90 #elif defined(CONFIG_SYS_INTEL_BOOT) 91 # define CONFIG_SYS_UBOOT_END 0x3FFFF 92 #endif 93 #define CONFIG_EXTRA_ENV_SETTINGS \ 94 "netdev=eth0\0" \ 95 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 96 "loadaddr=0x40010000\0" \ 97 "uboot=u-boot.bin\0" \ 98 "load=tftp ${loadaddr} ${uboot}\0" \ 99 "upd=run load; run prog\0" \ 100 "prog=prot off " __stringify(CONFIG_SYS_FLASH_BASE) \ 101 " " __stringify(CONFIG_SYS_UBOOT_END) ";" \ 102 "era " __stringify(CONFIG_SYS_FLASH_BASE) " " \ 103 __stringify(CONFIG_SYS_UBOOT_END) ";" \ 104 "cp.b ${loadaddr} " __stringify(CONFIG_SYS_FLASH_BASE) \ 105 " ${filesize}; save\0" \ 106 "" 107 #endif 108 109 /* ATA configuration */ 110 #define CONFIG_IDE_RESET 1 111 #define CONFIG_IDE_PREINIT 1 112 #define CONFIG_ATAPI 113 #undef CONFIG_LBA48 114 115 #define CONFIG_SYS_IDE_MAXBUS 1 116 #define CONFIG_SYS_IDE_MAXDEVICE 2 117 118 #define CONFIG_SYS_ATA_BASE_ADDR 0x90000000 119 #define CONFIG_SYS_ATA_IDE0_OFFSET 0 120 121 #define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ 122 #define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ 123 #define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ 124 #define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ 125 126 /* Realtime clock */ 127 #define CONFIG_MCFRTC 128 #undef RTC_DEBUG 129 #define CONFIG_SYS_RTC_OSCILLATOR (32 * CONFIG_SYS_HZ) 130 131 /* Timer */ 132 #define CONFIG_MCFTMR 133 #undef CONFIG_MCFPIT 134 135 /* I2c */ 136 #define CONFIG_SYS_I2C 137 #define CONFIG_SYS_I2C_FSL 138 #define CONFIG_SYS_FSL_I2C_SPEED 80000 139 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 140 #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 141 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 142 143 /* DSPI and Serial Flash */ 144 #define CONFIG_CF_DSPI 145 #define CONFIG_SYS_SBFHDR_SIZE 0x13 146 147 /* PCI */ 148 #ifdef CONFIG_CMD_PCI 149 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 150 151 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 4 152 153 #define CONFIG_SYS_PCI_MEM_BUS 0xA0000000 154 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS 155 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 156 157 #define CONFIG_SYS_PCI_IO_BUS 0xB1000000 158 #define CONFIG_SYS_PCI_IO_PHYS CONFIG_SYS_PCI_IO_BUS 159 #define CONFIG_SYS_PCI_IO_SIZE 0x01000000 160 161 #define CONFIG_SYS_PCI_CFG_BUS 0xB0000000 162 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS 163 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000 164 #endif 165 166 /* FPGA - Spartan 2 */ 167 /* experiment 168 #define CONFIG_FPGA_COUNT 1 169 #define CONFIG_SYS_FPGA_PROG_FEEDBACK 170 #define CONFIG_SYS_FPGA_CHECK_CTRLC 171 */ 172 173 /* Input, PCI, Flexbus, and VCO */ 174 #define CONFIG_EXTRA_CLOCK 175 176 #define CONFIG_PRAM 2048 /* 2048 KB */ 177 178 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) 179 180 #define CONFIG_SYS_MBAR 0xFC000000 181 182 /* 183 * Low Level Configuration Settings 184 * (address mappings, register initial values, etc.) 185 * You should know what you are doing if you make changes here. 186 */ 187 188 /*----------------------------------------------------------------------- 189 * Definitions for initial stack pointer and data area (in DPRAM) 190 */ 191 #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 192 #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */ 193 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 194 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 32) 195 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 196 #define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) 197 198 /*----------------------------------------------------------------------- 199 * Start addresses for the final memory configuration 200 * (Set up by the startup code) 201 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 202 */ 203 #define CONFIG_SYS_SDRAM_BASE 0x40000000 204 #define CONFIG_SYS_SDRAM_BASE1 0x48000000 205 #define CONFIG_SYS_SDRAM_SIZE 256 /* SDRAM size in MB */ 206 #define CONFIG_SYS_SDRAM_CFG1 0x65311610 207 #define CONFIG_SYS_SDRAM_CFG2 0x59670000 208 #define CONFIG_SYS_SDRAM_CTRL 0xEA0B2000 209 #define CONFIG_SYS_SDRAM_EMOD 0x40010000 210 #define CONFIG_SYS_SDRAM_MODE 0x00010033 211 #define CONFIG_SYS_SDRAM_DRV_STRENGTH 0xAA 212 213 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 214 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 215 216 #ifdef CONFIG_CF_SBF 217 # define CONFIG_SERIAL_BOOT 218 # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) 219 #else 220 # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 221 #endif 222 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 223 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 224 225 /* Reserve 256 kB for malloc() */ 226 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 227 228 /* 229 * For booting Linux, the board info and command line data 230 * have to be in the first 8 MB of memory, since this is 231 * the maximum mapped by the Linux kernel during initialization ?? 232 */ 233 /* Initial Memory map for Linux */ 234 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 235 236 /* 237 * Configuration for environment 238 * Environment is not embedded in u-boot. First time runing may have env 239 * crc error warning if there is no correct environment on the flash. 240 */ 241 #undef CONFIG_ENV_OVERWRITE 242 243 /*----------------------------------------------------------------------- 244 * FLASH organization 245 */ 246 #ifdef CONFIG_SYS_STMICRO_BOOT 247 # define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 248 # define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS1_BASE 249 #endif 250 #ifdef CONFIG_SYS_ATMEL_BOOT 251 # define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 252 # define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS0_BASE 253 # define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_CS1_BASE 254 #endif 255 #ifdef CONFIG_SYS_INTEL_BOOT 256 # define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 257 # define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS0_BASE 258 # define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_CS1_BASE 259 #endif 260 261 #ifdef CONFIG_SYS_FLASH_CFI 262 263 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ 264 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT 265 # define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ 266 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 267 # define CONFIG_SYS_FLASH_CHECKSUM 268 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE } 269 # define CONFIG_FLASH_CFI_LEGACY 270 271 #ifdef CONFIG_FLASH_CFI_LEGACY 272 # define CONFIG_SYS_ATMEL_REGION 4 273 # define CONFIG_SYS_ATMEL_TOTALSECT 11 274 # define CONFIG_SYS_ATMEL_SECT {1, 2, 1, 7} 275 # define CONFIG_SYS_ATMEL_SECTSZ {0x4000, 0x2000, 0x8000, 0x10000} 276 #endif 277 #endif 278 279 /* 280 * This is setting for JFFS2 support in u-boot. 281 * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. 282 */ 283 #ifdef CONFIG_CMD_JFFS2 284 #ifdef CF_STMICRO_BOOT 285 # define CONFIG_JFFS2_DEV "nor1" 286 # define CONFIG_JFFS2_PART_SIZE 0x01000000 287 # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH2_BASE + 0x500000) 288 #endif 289 #ifdef CONFIG_SYS_ATMEL_BOOT 290 # define CONFIG_JFFS2_DEV "nor1" 291 # define CONFIG_JFFS2_PART_SIZE 0x01000000 292 # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH1_BASE + 0x500000) 293 #endif 294 #ifdef CONFIG_SYS_INTEL_BOOT 295 # define CONFIG_JFFS2_DEV "nor0" 296 # define CONFIG_JFFS2_PART_SIZE (0x01000000 - 0x500000) 297 # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000) 298 #endif 299 #endif 300 301 /*----------------------------------------------------------------------- 302 * Cache Configuration 303 */ 304 #define CONFIG_SYS_CACHELINE_SIZE 16 305 306 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 307 CONFIG_SYS_INIT_RAM_SIZE - 8) 308 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 309 CONFIG_SYS_INIT_RAM_SIZE - 4) 310 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) 311 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 312 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 313 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 314 CF_ACR_EN | CF_ACR_SM_ALL) 315 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ 316 CF_CACR_ICINVA | CF_CACR_EUSP) 317 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 318 CF_CACR_DEC | CF_CACR_DDCM_P | \ 319 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 320 321 /*----------------------------------------------------------------------- 322 * Memory bank definitions 323 */ 324 /* 325 * CS0 - NOR Flash 1, 2, 4, or 8MB 326 * CS1 - CompactFlash and registers 327 * CS2 - CPLD 328 * CS3 - FPGA 329 * CS4 - Available 330 * CS5 - Available 331 */ 332 333 #if defined(CONFIG_SYS_ATMEL_BOOT) || defined(CONFIG_SYS_STMICRO_BOOT) 334 /* Atmel Flash */ 335 #define CONFIG_SYS_CS0_BASE 0x04000000 336 #define CONFIG_SYS_CS0_MASK 0x00070001 337 #define CONFIG_SYS_CS0_CTRL 0x00001140 338 /* Intel Flash */ 339 #define CONFIG_SYS_CS1_BASE 0x00000000 340 #define CONFIG_SYS_CS1_MASK 0x01FF0001 341 #define CONFIG_SYS_CS1_CTRL 0x00000D60 342 343 #define CONFIG_SYS_ATMEL_BASE CONFIG_SYS_CS0_BASE 344 #else 345 /* Intel Flash */ 346 #define CONFIG_SYS_CS0_BASE 0x00000000 347 #define CONFIG_SYS_CS0_MASK 0x01FF0001 348 #define CONFIG_SYS_CS0_CTRL 0x00000D60 349 /* Atmel Flash */ 350 #define CONFIG_SYS_CS1_BASE 0x04000000 351 #define CONFIG_SYS_CS1_MASK 0x00070001 352 #define CONFIG_SYS_CS1_CTRL 0x00001140 353 354 #define CONFIG_SYS_ATMEL_BASE CONFIG_SYS_CS1_BASE 355 #endif 356 357 /* CPLD */ 358 #define CONFIG_SYS_CS2_BASE 0x08000000 359 #define CONFIG_SYS_CS2_MASK 0x00070001 360 #define CONFIG_SYS_CS2_CTRL 0x003f1140 361 362 /* FPGA */ 363 #define CONFIG_SYS_CS3_BASE 0x09000000 364 #define CONFIG_SYS_CS3_MASK 0x00070001 365 #define CONFIG_SYS_CS3_CTRL 0x00000020 366 367 #endif /* _M54455EVB_H */ 368