Searched full:specifies (Results 1 – 25 of 2321) sorted by relevance
12345678910>>...93
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/nios2/ |
| D | nios2.txt | 3 This binding specifies what properties available in the device tree
13 - interrupt-controller: Specifies that the node is an interrupt controller
14 - #interrupt-cells: Specifies the number of cells needed to encode an
21 - altr,pid-num-bits: Specifies the number of bits to use to represent the process
23 - altr,tlb-num-ways: Specifies the number of set-associativity ways in the TLB.
24 - altr,tlb-num-entries: Specifies the number of entries in the TLB.
25 - altr,tlb-ptr-sz: Specifies size of TLB pointer.
26 - altr,has-mul: Specifies CPU hardware multipy support, should be 1.
27 - altr,has-mmu: Specifies CPU support MMU support, should be 1.
28 - altr,has-initda: Specifies CPU support initda instruction, should be 1.
[all …]
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/nios2/ |
| D | nios2.txt | 3 This binding specifies what properties available in the device tree
13 - interrupt-controller: Specifies that the node is an interrupt controller
14 - #interrupt-cells: Specifies the number of cells needed to encode an
21 - altr,pid-num-bits: Specifies the number of bits to use to represent the process
23 - altr,tlb-num-ways: Specifies the number of set-associativity ways in the TLB.
24 - altr,tlb-num-entries: Specifies the number of entries in the TLB.
25 - altr,tlb-ptr-sz: Specifies size of TLB pointer.
26 - altr,has-mul: Specifies CPU hardware multipy support, should be 1.
27 - altr,has-mmu: Specifies CPU support MMU support, should be 1.
28 - altr,has-initda: Specifies CPU support initda instruction, should be 1.
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/input/ |
| D | iqs269a.yaml | 47 Specifies the power mode during suspend as follows:
62 description: Specifies the ultra-low-power mode update rate.
75 Specifies the long-term average filter strength during low-power mode.
82 Specifies the raw count filter strength during low-power mode.
89 Specifies the long-term average filter strength during normal-power mode.
96 Specifies the raw count filter strength during normal-power mode.
102 description: Specifies the report rate (in ms) during normal-power mode.
108 description: Specifies the report rate (in ms) during low-power mode.
115 description: Specifies the report rate (in ms) during ultra-low-power mode.
123 Specifies the length of time (in ms) to wait for an event during normal-
[all …]
|
| /kernel/linux/linux-5.10/Documentation/admin-guide/cgroup-v1/ |
| D | blkio-controller.rst | 97 - Specifies per cgroup weight. This is default weight of the group
136 third field specifies the disk time allocated to group in
142 third field specifies the number of sectors transferred by the
149 device, third field specifies the operation type and the fourth field
150 specifies the number of bytes.
156 device, third field specifies the operation type and the fourth field
157 specifies the number of IOs.
170 specifies the operation type and the fourth field specifies the
185 minor number of the device, third field specifies the operation type
186 and the fourth field specifies the io_wait_time in ns.
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/pci/ |
| D | ralink,rt3883-pci.txt | 9 - reg: specifies the physical base address of the controller and
12 - #address-cells: specifies the number of cells needed to encode an
15 - #size-cells: specifies the number of cells used to represent the size
18 - ranges: specifies the translation between child address space and parent
37 - #address-cells: specifies the number of cells needed to encode an
41 - #interrupt-cells: specifies the number of cells needed to encode an
44 - interrupts: specifies the interrupt source of the parent interrupt
52 - #address-cells: specifies the number of cells needed to encode an
55 - #size-cells: specifies the number of cells used to represent the size
58 - #interrupt-cells: specifies the number of cells needed to encode an
[all …]
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/pci/ |
| D | ralink,rt3883-pci.txt | 9 - reg: specifies the physical base address of the controller and
12 - #address-cells: specifies the number of cells needed to encode an
15 - #size-cells: specifies the number of cells used to represent the size
18 - ranges: specifies the translation between child address space and parent
37 - #address-cells: specifies the number of cells needed to encode an
41 - #interrupt-cells: specifies the number of cells needed to encode an
44 - interrupts: specifies the interrupt source of the parent interrupt
52 - #address-cells: specifies the number of cells needed to encode an
55 - #size-cells: specifies the number of cells used to represent the size
58 - #interrupt-cells: specifies the number of cells needed to encode an
[all …]
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/net/ |
| D | cpsw.txt | 14 - cpdma_channels : Specifies number of channels in CPDMA
15 - ale_entries : Specifies No of entries ALE can hold
16 - bd_ram_size : Specifies internal descriptor RAM size
17 - mac_control : Specifies Default MAC control register content
19 - slaves : Specifies number for slaves
20 - active_slave : Specifies the slave to use for time stamping,
22 - cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection
29 - dual_emac : Specifies Switch to act as Dual EMAC
49 - dual_emac_res_vlan : Specifies VID to be used to segregate the ports
51 - phy_id : Specifies slave phy id (deprecated, use phy-handle)
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/ |
| D | cpsw.txt | 14 - cpdma_channels : Specifies number of channels in CPDMA
15 - ale_entries : Specifies No of entries ALE can hold
16 - bd_ram_size : Specifies internal descriptor RAM size
17 - mac_control : Specifies Default MAC control register content
19 - slaves : Specifies number for slaves
20 - active_slave : Specifies the slave to use for time stamping,
22 - cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection
30 - dual_emac : Specifies Switch to act as Dual EMAC
51 - dual_emac_res_vlan : Specifies VID to be used to segregate the ports
52 - phy_id : Specifies slave phy id (deprecated, use phy-handle)
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/usb/ |
| D | octeon-usb.txt | 9 - reg: specifies the physical base address of the USBN block and
12 - #address-cells: specifies the number of cells needed to encode an
15 - #size-cells: specifies the number of cells used to represent the size
18 - ranges: specifies the translation between child address space and parent
40 - reg: specifies the physical base address of the USBC block and
43 - interrupts: specifies the interrupt number for the USB controller.
|
| D | usb251xb.txt | 46 - sp-disabled-ports : Specifies the ports which will be self-power disabled
47 - bp-disabled-ports : Specifies the ports which will be bus-power disabled
48 - sp-max-total-current-microamp: Specifies max current consumed by the hub
52 - bp-max-total-current-microamp: Specifies max current consumed by the hub
56 - sp-max-removable-current-microamp: Specifies max current consumed by the hub
60 - bp-max-removable-current-microamp: Specifies max current consumed by the hub
64 - power-on-time-ms : Specifies the time it takes from the time the host
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/usb/ |
| D | octeon-usb.txt | 9 - reg: specifies the physical base address of the USBN block and
12 - #address-cells: specifies the number of cells needed to encode an
15 - #size-cells: specifies the number of cells used to represent the size
18 - ranges: specifies the translation between child address space and parent
40 - reg: specifies the physical base address of the USBC block and
43 - interrupts: specifies the interrupt number for the USB controller.
|
| D | usb251xb.txt | 47 - sp-disabled-ports : Specifies the ports which will be self-power disabled
48 - bp-disabled-ports : Specifies the ports which will be bus-power disabled
49 - sp-max-total-current-microamp: Specifies max current consumed by the hub
53 - bp-max-total-current-microamp: Specifies max current consumed by the hub
57 - sp-max-removable-current-microamp: Specifies max current consumed by the hub
61 - bp-max-removable-current-microamp: Specifies max current consumed by the hub
65 - power-on-time-ms : Specifies the time it takes from the time the host
68 - swap-dx-lanes : Specifies the ports which will swap the differential-pair
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/mmc/ |
| D | fsl-esdhc.txt | 25 - clock-frequency : specifies eSDHC base clock frequency.
28 - sdhci,wp-inverted : specifies that eSDHC controller reports
31 - sdhci,1-bit-only : specifies that a controller can only handle
34 - sdhci,auto-cmd12: specifies that a controller can only handle auto
36 - voltage-ranges : two cells are required, first cell specifies minimum
37 slot voltage (mV), second cell specifies maximum slot voltage (mV).
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/mmc/ |
| D | fsl-esdhc.txt | 24 - clock-frequency : specifies eSDHC base clock frequency.
27 - sdhci,wp-inverted : specifies that eSDHC controller reports
30 - sdhci,1-bit-only : specifies that a controller can only handle
33 - sdhci,auto-cmd12: specifies that a controller can only handle auto
35 - voltage-ranges : two cells are required, first cell specifies minimum
36 slot voltage (mV), second cell specifies maximum slot voltage (mV).
|
| /kernel/linux/linux-4.19/Documentation/cgroup-v1/ |
| D | blkio-controller.txt | 145 - Specifies per cgroup weight. This is default weight of the group
186 third field specifies the disk time allocated to group in
192 third field specifies the number of sectors transferred by the
199 device, third field specifies the operation type and the fourth field
200 specifies the number of bytes.
206 device, third field specifies the operation type and the fourth field
207 specifies the number of IOs.
220 specifies the operation type and the fourth field specifies the
235 minor number of the device, third field specifies the operation type
236 and the fourth field specifies the io_wait_time in ns.
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/nfc/ |
| D | nfcmrvl.txt | 11 - pintctrl-0: Specifies the pin control groups used for this controller.
13 - hci-muxed: Specifies that the chip is muxing NCI over HCI frames.
16 - flow-control: Specifies that the chip is using RTS/CTS.
17 - break-control: Specifies that the chip needs specific break management.
20 - i2c-int-falling: Specifies that the chip read event shall be trigged on
22 - i2c-int-rising: Specifies that the chip read event shall be trigged on
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/net/nfc/ |
| D | nfcmrvl.txt | 11 - pintctrl-0: Specifies the pin control groups used for this controller.
13 - hci-muxed: Specifies that the chip is muxing NCI over HCI frames.
16 - flow-control: Specifies that the chip is using RTS/CTS.
17 - break-control: Specifies that the chip needs specific break management.
20 - i2c-int-falling: Specifies that the chip read event shall be trigged on
22 - i2c-int-rising: Specifies that the chip read event shall be trigged on
|
| /kernel/linux/linux-4.19/Documentation/ABI/testing/ |
| D | sysfs-kernel-slab | 19 The aliases file is read-only and specifies how many caches
28 The align file is read-only and specifies the cache's object
105 The cache_dma file is read-only and specifies whether objects
137 The ctor file is read-only and specifies the cache's object
200 The destroy_by_rcu file is read-only and specifies whether
286 The hwcache_align file is read-only and specifies whether
295 The min_partial file specifies how many empty slabs shall
306 The object_size file is read-only and specifies the cache's
334 The file objs_per_slab is read-only and specifies how many
344 The order file specifies the page order at which new slabs are
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/security/tpm/ |
| D | ibmvtpm.txt | 7 - device_type : specifies type of virtual device
13 - ibm,#dma-address-cells: specifies the number of cells that are used to
16 - ibm,#dma-size-cells : specifies the number of cells that are used to
18 - ibm,my-dma-window : specifies DMA window associated with this virtual
20 - ibm,loc-code : specifies the unique and persistent location code
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/security/tpm/ |
| D | ibmvtpm.txt | 7 - device_type : specifies type of virtual device
13 - ibm,#dma-address-cells: specifies the number of cells that are used to
16 - ibm,#dma-size-cells : specifies the number of cells that are used to
18 - ibm,my-dma-window : specifies DMA window associated with this virtual
20 - ibm,loc-code : specifies the unique and persistent location code
|
| /kernel/linux/linux-5.10/include/sound/sof/ |
| D | channel_map.h | 16 * \brief Channel map, specifies transformation of one-to-many or many-to-one.
18 * In case of one-to-many specifies how the output channels are computed out of
20 * in case of many-to-one specifies how a single target channel is computed
23 * Channel index specifies position of the channel in the stream on the 'one'
48 * num_ch_map Specifies number of items in the ch_map.
|
| /kernel/linux/linux-5.10/Documentation/ABI/testing/ |
| D | sysfs-kernel-slab | 19 The aliases file is read-only and specifies how many caches
28 The align file is read-only and specifies the cache's object
105 The cache_dma file is read-only and specifies whether objects
137 The ctor file is read-only and specifies the cache's object
200 The destroy_by_rcu file is read-only and specifies whether
286 The hwcache_align file is read-only and specifies whether
295 The min_partial file specifies how many empty slabs shall
306 The object_size file is read-only and specifies the cache's
334 The file objs_per_slab is read-only and specifies how many
344 The order file specifies the page order at which new slabs are
[all …]
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/powerpc/fsl/ |
| D | srio-rmu.txt | 21 Definition: A standard property. Specifies the physical address and
52 Definition: A standard property. Specifies the physical address and
59 Definition: Specifies the interrupts generated by this device. The
82 Definition: A standard property. Specifies the physical address and
89 Definition: Specifies the interrupts generated by this device. The
112 Definition: A standard property. Specifies the physical address and
119 Definition: Specifies the interrupts generated by this device. The
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/powerpc/fsl/ |
| D | srio-rmu.txt | 21 Definition: A standard property. Specifies the physical address and
52 Definition: A standard property. Specifies the physical address and
59 Definition: Specifies the interrupts generated by this device. The
82 Definition: A standard property. Specifies the physical address and
89 Definition: Specifies the interrupts generated by this device. The
112 Definition: A standard property. Specifies the physical address and
119 Definition: Specifies the interrupts generated by this device. The
|
| D | mpic-msgr.txt | 3 This binding specifies what properties must be available in the device tree
9 - compatible: Specifies the compatibility list for the message register
14 - reg: Specifies the base physical address(s) and size(s) of the
18 - interrupts: Specifies a list of interrupt-specifiers which are available
25 - mpic-msgr-receive-mask: Specifies what registers in the containing block
|
12345678910>>...93