| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/sound/ |
| D | tlv320aic3x.txt | 1 Texas Instruments - tlv320aic3x Codec module
7 - compatible - "string" - One of:
8 "ti,tlv320aic3x" - Generic TLV320AIC3x device
9 "ti,tlv320aic33" - TLV320AIC33
10 "ti,tlv320aic3007" - TLV320AIC3007
11 "ti,tlv320aic3106" - TLV320AIC3106
12 "ti,tlv320aic3104" - TLV320AIC3104
15 - reg - <int> - I2C slave address
20 - reset-gpios - GPIO specification for the active low RESET input.
21 - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
[all …]
|
| D | tlv320aic31xx.txt | 1 Texas Instruments - tlv320aic31xx Codec module
7 - compatible - "string" - One of:
8 "ti,tlv320aic310x" - Generic TLV320AIC31xx with mono speaker amp
9 "ti,tlv320aic311x" - Generic TLV320AIC31xx with stereo speaker amp
10 "ti,tlv320aic3100" - TLV320AIC3100 (mono speaker amp, no MiniDSP)
11 "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP)
12 "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP)
13 "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP)
14 "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP)
15 "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP)
[all …]
|
| D | cs42l52.txt | 5 - compatible : "cirrus,cs42l52"
7 - reg : the I2C address of the device for I2C
11 - cirrus,reset-gpio : GPIO controller's phandle and the number
14 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
21 - cirrus,mica-differential-cfg : boolean, If present, then the MICA input is configured
22 as a differential input. If not present then the MICA input is configured as
23 Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
25 - cirrus,micb-differential-cfg : boolean, If present, then the MICB input is configured
26 as a differential input. If not present then the MICB input is configured as
27 Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
[all …]
|
| D | cs42l56.txt | 5 - compatible : "cirrus,cs42l56"
7 - reg : the I2C address of the device for I2C
9 - VA-supply, VCP-supply, VLDO-supply : power supplies for the device,
14 - cirrus,gpio-nreset : GPIO controller's phandle and the number
17 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
24 - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
25 as a pseudo-differential input referenced to AIN1REF/AIN3A.
27 - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
28 as a pseudo-differential input referenced to AIN2REF/AIN3B.
30 - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
[all …]
|
| D | rt5651.txt | 7 - compatible : "realtek,rt5651".
9 - reg : The I2C address of the device.
13 - realtek,in2-differential
14 Boolean. Indicate MIC2 input are differential, rather than single-ended.
16 - realtek,dmic-en
19 - realtek,jack-detect-source
21 1: Use JD1_1 pin for jack-detect
22 2: Use JD1_2 pin for jack-detect
23 3: Use JD2 pin for jack-detect
25 - realtek,jack-detect-not-inverted
[all …]
|
| D | da7219.txt | 8 - compatible : Should be "dlg,da7219"
9 - reg: Specifies the I2C slave address
11 - interrupts : IRQ line info for DA7219.
12 (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
15 - VDD-supply: VDD power supply for the device
16 - VDDMIC-supply: VDDMIC power supply for the device
17 - VDDIO-supply: VDDIO power supply for the device
22 - interrupt-names : Name associated with interrupt line. Should be "wakeup" if
24 - wakeup-source: Flag to indicate this device can wake system (suspend/resume).
26 - #clock-cells : Should be set to '<1>', two clock sources provided;
[all …]
|
| D | wm8994.txt | 8 - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958".
10 - reg : the I2C address of the device for I2C, the chip select
13 - gpio-controller : Indicates this device is a GPIO controller.
14 - #gpio-cells : Must be 2. The first cell is the pin number and the
17 - power supplies for the device, as covered in
20 - for wlf,wm1811 and wlf,wm8958:
21 AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply,
22 DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply
23 - for wlf,wm8994:
24 AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply,
[all …]
|
| D | rt5640.txt | 7 - compatible : One of "realtek,rt5640" or "realtek,rt5639".
9 - reg : The I2C address of the device.
11 - interrupts : The CODEC's interrupt output.
15 - clocks: The phandle of the master clock to the CODEC
16 - clock-names: Should be "mclk"
18 - realtek,in1-differential
19 - realtek,in2-differential
20 - realtek,in3-differential
21 Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
23 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
[all …]
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/sound/ |
| D | tlv320aic3x.txt | 1 Texas Instruments - tlv320aic3x Codec module
7 - compatible - "string" - One of:
8 "ti,tlv320aic3x" - Generic TLV320AIC3x device
9 "ti,tlv320aic33" - TLV320AIC33
10 "ti,tlv320aic3007" - TLV320AIC3007
11 "ti,tlv320aic3106" - TLV320AIC3106
12 "ti,tlv320aic3104" - TLV320AIC3104
15 - reg - <int> - I2C slave address
20 - reset-gpios - GPIO specification for the active low RESET input.
21 - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
[all …]
|
| D | tlv320aic31xx.txt | 1 Texas Instruments - tlv320aic31xx Codec module
7 - compatible - "string" - One of:
8 "ti,tlv320aic310x" - Generic TLV320AIC31xx with mono speaker amp
9 "ti,tlv320aic311x" - Generic TLV320AIC31xx with stereo speaker amp
10 "ti,tlv320aic3100" - TLV320AIC3100 (mono speaker amp, no MiniDSP)
11 "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP)
12 "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP)
13 "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP)
14 "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP)
15 "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP)
[all …]
|
| D | cs42l52.txt | 5 - compatible : "cirrus,cs42l52"
7 - reg : the I2C address of the device for I2C
11 - cirrus,reset-gpio : GPIO controller's phandle and the number
14 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
21 - cirrus,mica-differential-cfg : boolean, If present, then the MICA input is configured
22 as a differential input. If not present then the MICA input is configured as
23 Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
25 - cirrus,micb-differential-cfg : boolean, If present, then the MICB input is configured
26 as a differential input. If not present then the MICB input is configured as
27 Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
[all …]
|
| D | cs42l56.txt | 5 - compatible : "cirrus,cs42l56"
7 - reg : the I2C address of the device for I2C
9 - VA-supply, VCP-supply, VLDO-supply : power supplies for the device,
14 - cirrus,gpio-nreset : GPIO controller's phandle and the number
17 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
24 - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
25 as a pseudo-differential input referenced to AIN1REF/AIN3A.
27 - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
28 as a pseudo-differential input referenced to AIN2REF/AIN3B.
30 - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
[all …]
|
| D | rt5651.txt | 7 - compatible : "realtek,rt5651".
9 - reg : The I2C address of the device.
13 - realtek,in2-differential
14 Boolean. Indicate MIC2 input are differential, rather than single-ended.
16 - realtek,dmic-en
19 - realtek,jack-detect-source
21 1: Use JD1_1 pin for jack-detect
22 2: Use JD1_2 pin for jack-detect
23 3: Use JD2 pin for jack-detect
25 - realtek,over-current-threshold-microamp
[all …]
|
| D | da7219.txt | 8 - compatible : Should be "dlg,da7219"
9 - reg: Specifies the I2C slave address
11 - interrupts : IRQ line info for DA7219.
12 (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
15 - VDD-supply: VDD power supply for the device
16 - VDDMIC-supply: VDDMIC power supply for the device
17 - VDDIO-supply: VDDIO power supply for the device
22 - interrupt-names : Name associated with interrupt line. Should be "wakeup" if
24 - wakeup-source: Flag to indicate this device can wake system (suspend/resume).
26 - #clock-cells : Should be set to '<0>', only one clock source provided;
[all …]
|
| D | wm8994.txt | 8 - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958".
10 - reg : the I2C address of the device for I2C, the chip select
13 - gpio-controller : Indicates this device is a GPIO controller.
14 - #gpio-cells : Must be 2. The first cell is the pin number and the
17 - power supplies for the device, as covered in
20 - for wlf,wm1811 and wlf,wm8958:
21 AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply,
22 DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply
23 - for wlf,wm8994:
24 AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply,
[all …]
|
| D | rt5640.txt | 7 - compatible : One of "realtek,rt5640" or "realtek,rt5639".
9 - reg : The I2C address of the device.
11 - interrupts : The CODEC's interrupt output.
15 - clocks: The phandle of the master clock to the CODEC
16 - clock-names: Should be "mclk"
18 - realtek,in1-differential
19 - realtek,in2-differential
20 - realtek,in3-differential
21 Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
23 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
[all …]
|
| /kernel/linux/linux-4.19/Documentation/devicetree/bindings/extcon/ |
| D | extcon-arizona.txt | 11 - wlf,hpdet-channel : Headphone detection channel.
12 ARIZONA_ACCDET_MODE_HPL or 1 - Headphone detect mode is set to HPDETL
13 ARIZONA_ACCDET_MODE_HPR or 2 - Headphone detect mode is set to HPDETR
17 - wlf,use-jd2 : Use the additional JD input along with JD1 for dual pin jack
19 - wlf,use-jd2-nopull : Internal pull on JD2 is disabled when used for
21 - wlf,jd-invert : Invert the polarity of the jack detection switch
23 - wlf,micd-software-compare : Use a software comparison to determine mic
25 - wlf,micd-detect-debounce : Additional software microphone detection
27 - wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset
29 - wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/mfd/ |
| D | cirrus,lochnagar.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - patches@opensource.cirrus.com
15 Logic devices on mini-cards, as well as allowing connection of
25 [2] include/dt-bindings/pinctrl/lochnagar.h
26 [3] include/dt-bindings/clock/lochnagar.h
28 And these documents for the required sub-node binding details:
35 - if:
39 - cirrus,lochnagar2
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/extcon/ |
| D | wlf,arizona.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - patches@opensource.cirrus.com
20 wlf,hpdet-channel:
30 wlf,use-jd2:
32 Use the additional JD input along with JD1 for dual pin jack detection.
35 wlf,use-jd2-nopull:
40 wlf,jd-invert:
45 wlf,micd-software-compare:
[all …]
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | s5pv210-fascinate4g.dts | 1 // SPDX-License-Identifier: GPL-2.0
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6 #include "s5pv210-aries.dtsi"
9 model = "Samsung Galaxy S Fascinate 4G (SGH-T959P) based on S5PV210";
13 stdout-path = &uart2;
16 gpio-keys {
17 compatible = "gpio-keys";
23 wakeup-source;
[all …]
|
| D | s5pv210-galaxys.dts | 1 // SPDX-License-Identifier: GPL-2.0
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6 #include "s5pv210-aries.dtsi"
9 model = "Samsung Galaxy S1 (GT-I9000) based on S5PV210";
13 stdout-path = &uart2;
16 nand_pwrseq: nand-pwrseq {
17 compatible = "mmc-pwrseq-simple";
18 reset-gpios = <&gpj2 7 GPIO_ACTIVE_LOW>;
[all …]
|
| /kernel/linux/linux-5.10/include/linux/mfd/arizona/ |
| D | pdata.h | 1 /* SPDX-License-Identifier: GPL-2.0-only */
11 #include <dt-bindings/mfd/arizona.h>
12 #include <linux/regulator/arizona-ldo1.h>
13 #include <linux/regulator/arizona-micsupp.h>
36 #define ARIZONA_GPN_FN_MASK 0x007F /* GPN_FN - [6:0] */
37 #define ARIZONA_GPN_FN_SHIFT 0 /* GPN_FN - [6:0] */
38 #define ARIZONA_GPN_FN_WIDTH 7 /* GPN_FN - [6:0] */
74 int key; /** Key to report to input layer */
147 /** Force MICBIAS on for mic detect */
161 /** MICBIAS configurations */
[all …]
|
| /kernel/linux/linux-4.19/include/linux/mfd/arizona/ |
| D | pdata.h | 14 #include <dt-bindings/mfd/arizona.h>
15 #include <linux/regulator/arizona-ldo1.h>
16 #include <linux/regulator/arizona-micsupp.h>
39 #define ARIZONA_GPN_FN_MASK 0x007F /* GPN_FN - [6:0] */
40 #define ARIZONA_GPN_FN_SHIFT 0 /* GPN_FN - [6:0] */
41 #define ARIZONA_GPN_FN_WIDTH 7 /* GPN_FN - [6:0] */
77 int key; /** Key to report to input layer */
150 /** Force MICBIAS on for mic detect */
164 /** MICBIAS configurations */
165 struct arizona_micbias micbias[ARIZONA_MAX_MICBIAS]; member
[all …]
|
| /kernel/linux/linux-5.10/include/sound/ |
| D | cs42l56.h | 1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * linux/sound/cs42l56.h -- Platform data for CS42L56
16 /* MICBIAS Level. Check datasheet Pg48 */
19 /* Analog Input 1A Reference 0=Single 1=Pseudo-Differential */
22 /* Analog Input 2A Reference 0=Single 1=Pseudo-Differential */
25 /* Analog Input 1B Reference 0=Single 1=Pseudo-Differential */
28 /* Analog Input 2B Reference 0=Single 1=Pseudo-Differential */
|
| /kernel/linux/linux-4.19/include/sound/ |
| D | cs42l56.h | 2 * linux/sound/cs42l56.h -- Platform data for CS42L56
19 /* MICBIAS Level. Check datasheet Pg48 */
22 /* Analog Input 1A Reference 0=Single 1=Pseudo-Differential */
25 /* Analog Input 2A Reference 0=Single 1=Pseudo-Differential */
28 /* Analog Input 1B Reference 0=Single 1=Pseudo-Differential */
31 /* Analog Input 2B Reference 0=Single 1=Pseudo-Differential */
|