Home
last modified time | relevance | path

Searched +full:regulator +full:- +full:allow +full:- +full:bypass (Results 1 – 25 of 64) sorted by relevance

123

/kernel/linux/linux-4.19/Documentation/devicetree/bindings/regulator/
Dregulator.txt4 - regulator-name: A string used as a descriptive name for regulator outputs
5 - regulator-min-microvolt: smallest voltage consumers may set
6 - regulator-max-microvolt: largest voltage consumers may set
7 - regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
8 - regulator-min-microamp: smallest current consumers may set
9 - regulator-max-microamp: largest current consumers may set
10 - regulator-input-current-limit-microamp: maximum input current regulator allows
11 - regulator-always-on: boolean, regulator should never be disabled
12 - regulator-boot-on: bootloader/firmware enabled regulator
13 - regulator-allow-bypass: allow the regulator to go into bypass mode
[all …]
Dqcom,rpmh-regulator.txt3 rpmh-regulator devices support PMIC regulator management via the Voltage
4 Regulator Manager (VRM) and Oscillator Buffer (XOB) RPMh accelerators. The APPS
7 parameters for a given regulator: enable state, output voltage, and operating
8 mode. The XOB allows changing only a single parameter for a given regulator:
10 enable state of any PMIC peripheral. It is used for clock buffers, low-voltage
19 RPMh device node. The second level describes each regulator within the PMIC
23 The names used for regulator nodes must match those supported by a given PMIC.
24 Supported regulator node names:
25 PM8998: smps1 - smps13, ldo1 - ldo28, lvs1 - lvs2
27 PM8005: smps1 - smps4
[all …]
/kernel/linux/linux-5.10/arch/arm/boot/dts/
Ddra72-evm-tps65917.dtsi1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
8 * https://www.ti.com/lit/ds/symlink/tps65917-q1.pdf
14 interrupt-controller;
15 #interrupt-cells = <2>;
17 ti,system-power-controller;
20 compatible = "ti,tps65917-pmic";
22 smps1-in-supply = <&vsys_3v3>;
23 smps2-in-supply = <&vsys_3v3>;
24 smps3-in-supply = <&vsys_3v3>;
[all …]
Dimx6ul-ccimx6ulsom.dtsi1 // SPDX-License-Identifier: GPL-2.0
3 * Digi International's ConnectCore 6UL System-On-Module device tree source
12 reg = <0x80000000 0>; /* will be filled by U-Boot */
15 reserved-memory {
16 #address-cells = <1>;
17 #size-cells = <1>;
21 compatible = "shared-dma-pool";
24 linux,cma-default;
30 vref-supply = <&vdda_adc_3v3>;
34 pinctrl-names = "default";
[all …]
Ddra76-evm.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
5 /dts-v1/;
8 #include "dra7-evm-common.dtsi"
9 #include "dra76x-mmc-iodelay.dtsi"
10 #include <dt-bindings/net/ti-dp83867.h>
14 compatible = "ti,dra76-evm", "ti,dra762", "ti,dra7";
28 reserved-memory {
29 #address-cells = <2>;
30 #size-cells = <2>;
[all …]
Ddra7-evm.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
5 /dts-v1/;
8 #include "dra7-evm-common.dtsi"
9 #include "dra74x-mmc-iodelay.dtsi"
13 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7";
20 evm_12v0: fixedregulator-evm_12v0 {
22 compatible = "regulator-fixed";
23 regulator-name = "evm_12v0";
24 regulator-min-microvolt = <12000000>;
[all …]
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/regulator/
Dregulator.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/regulator/regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Liam Girdwood <lgirdwood@gmail.com>
11 - Mark Brown <broonie@kernel.org>
14 regulator-name:
15 description: A string used as a descriptive name for regulator outputs
18 regulator-min-microvolt:
21 regulator-max-microvolt:
[all …]
Dqcom,rpmh-regulator.txt3 rpmh-regulator devices support PMIC regulator management via the Voltage
4 Regulator Manager (VRM) and Oscillator Buffer (XOB) RPMh accelerators. The APPS
7 parameters for a given regulator: enable state, output voltage, and operating
8 mode. The XOB allows changing only a single parameter for a given regulator:
10 enable state of any PMIC peripheral. It is used for clock buffers, low-voltage
19 RPMh device node. The second level describes each regulator within the PMIC
23 The names used for regulator nodes must match those supported by a given PMIC.
24 Supported regulator node names:
25 PM8005: smps1 - smps4
26 PM8009: smps1 - smps2, ldo1 - ldo7
[all …]
/kernel/linux/linux-4.19/arch/arm/boot/dts/
Ddra72-evm-tps65917.dtsi2 * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
11 * http://www.ti.com/lit/ds/symlink/tps65917-q1.pdf
17 interrupt-controller;
18 #interrupt-cells = <2>;
20 ti,system-power-controller;
23 compatible = "ti,tps65917-pmic";
25 smps1-in-supply = <&vsys_3v3>;
26 smps2-in-supply = <&vsys_3v3>;
27 smps3-in-supply = <&vsys_3v3>;
28 smps4-in-supply = <&vsys_3v3>;
[all …]
Dimx6ul-ccimx6ulsom.dtsi1 // SPDX-License-Identifier: GPL-2.0
3 * Digi International's ConnectCore 6UL System-On-Module device tree source
10 reserved-memory {
11 #address-cells = <1>;
12 #size-cells = <1>;
16 compatible = "shared-dma-pool";
19 linux,cma-default;
25 vref-supply = <&vdda_adc_3v3>;
29 pinctrl-names = "default";
30 pinctrl-0 = <&pinctrl_gpmi_nand>;
[all …]
Ddra76-evm.dts2 * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
8 /dts-v1/;
11 #include "dra7-evm-common.dtsi"
12 #include "dra76x-mmc-iodelay.dtsi"
13 #include <dt-bindings/net/ti-dp83867.h>
17 compatible = "ti,dra76-evm", "ti,dra762", "ti,dra7";
24 vsys_12v0: fixedregulator-vsys12v0 {
26 compatible = "regulator-fixed";
27 regulator-name = "vsys_12v0";
28 regulator-min-microvolt = <12000000>;
[all …]
Ddra7-evm.dts2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
8 /dts-v1/;
11 #include "dra7-evm-common.dtsi"
12 #include "dra74x-mmc-iodelay.dtsi"
16 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7";
23 evm_12v0: fixedregulator-evm_12v0 {
25 compatible = "regulator-fixed";
26 regulator-name = "evm_12v0";
27 regulator-min-microvolt = <12000000>;
28 regulator-max-microvolt = <12000000>;
[all …]
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/mfd/
Dst,stpmic1.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
12 - pascal Paillet <p.paillet@st.com>
24 "#interrupt-cells":
27 interrupt-controller: true
36 const: st,stpmic1-onkey
40 - description: onkey-falling, happens when onkey is pressed. IT_PONKEY_F of pmic
41 - description: onkey-rising, happens when onkey is released. IT_PONKEY_R of pmic
43 interrupt-names:
[all …]
Dqcom-rpm.txt8 - compatible:
12 "qcom,rpm-apq8064"
13 "qcom,rpm-msm8660"
14 "qcom,rpm-msm8960"
15 "qcom,rpm-ipq8064"
16 "qcom,rpm-mdm9615"
18 - reg:
20 Value type: <prop-encoded-array>
23 - interrupts:
25 Value type: <prop-encoded-array>
[all …]
/kernel/linux/linux-4.19/drivers/regulator/
Dcore.c2 * core.c -- Voltage/Current Regulator framework.
30 #include <linux/regulator/of_regulator.h>
31 #include <linux/regulator/consumer.h>
32 #include <linux/regulator/driver.h>
33 #include <linux/regulator/machine.h>
37 #include <trace/events/regulator.h>
70 struct regulator_dev *regulator; member
108 static struct regulator *create_regulator(struct regulator_dev *rdev,
111 static void _regulator_put(struct regulator *regulator);
115 if (rdev->constraints && rdev->constraints->name) in rdev_get_name()
[all …]
Dof_regulator.c2 * OF helpers for regulator framework
16 #include <linux/regulator/machine.h>
17 #include <linux/regulator/driver.h>
18 #include <linux/regulator/of_regulator.h>
23 [PM_SUSPEND_MEM] = "regulator-state-mem",
24 [PM_SUSPEND_MAX] = "regulator-state-disk",
31 struct regulation_constraints *constraints = &(*init_data)->constraints; in of_get_regulation_constraints()
38 constraints->name = of_get_property(np, "regulator-name", NULL); in of_get_regulation_constraints()
40 if (!of_property_read_u32(np, "regulator-min-microvolt", &pval)) in of_get_regulation_constraints()
41 constraints->min_uV = pval; in of_get_regulation_constraints()
[all …]
/kernel/linux/linux-4.19/Documentation/devicetree/bindings/mfd/
Dqcom-rpm.txt8 - compatible:
12 "qcom,rpm-apq8064"
13 "qcom,rpm-msm8660"
14 "qcom,rpm-msm8960"
15 "qcom,rpm-ipq8064"
16 "qcom,rpm-mdm9615"
18 - reg:
20 Value type: <prop-encoded-array>
23 - interrupts:
25 Value type: <prop-encoded-array>
[all …]
/kernel/linux/linux-5.10/drivers/regulator/
Dcore.c1 // SPDX-License-Identifier: GPL-2.0-or-later
3 // core.c -- Voltage/Current Regulator framework.
23 #include <linux/regulator/of_regulator.h>
24 #include <linux/regulator/consumer.h>
25 #include <linux/regulator/coupler.h>
26 #include <linux/regulator/driver.h>
27 #include <linux/regulator/machine.h>
31 #include <trace/events/regulator.h>
67 struct regulator_dev *regulator; member
96 static int _regulator_disable(struct regulator *regulator);
[all …]
Dof_regulator.c1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * OF helpers for regulator framework
12 #include <linux/regulator/machine.h>
13 #include <linux/regulator/driver.h>
14 #include <linux/regulator/of_regulator.h>
19 [PM_SUSPEND_STANDBY] = "regulator-state-standby",
20 [PM_SUSPEND_MEM] = "regulator-state-mem",
21 [PM_SUSPEND_MAX] = "regulator-state-disk",
29 struct regulation_constraints *constraints = &(*init_data)->constraints; in of_get_regulation_constraints()
37 n_phandles = of_count_phandle_with_args(np, "regulator-coupled-with", in of_get_regulation_constraints()
[all …]
/kernel/linux/linux-5.10/arch/arm64/boot/dts/qcom/
Dsm8150-mtp.dts1 // SPDX-License-Identifier: BSD-3-Clause
3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
7 /dts-v1/;
9 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
10 #include <dt-bindings/gpio/gpio.h>
18 compatible = "qcom,sm8150-mtp";
25 stdout-path = "serial0:115200n8";
28 vph_pwr: vph-pwr-regulator {
29 compatible = "regulator-fixed";
30 regulator-name = "vph_pwr";
[all …]
Dsdm845-mtp.dts1 // SPDX-License-Identifier: GPL-2.0
8 /dts-v1/;
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
16 compatible = "qcom,sdm845-mtp", "qcom,sdm845";
23 stdout-path = "serial0:115200n8";
26 vph_pwr: vph-pwr-regulator {
27 compatible = "regulator-fixed";
28 regulator-name = "vph_pwr";
29 regulator-min-microvolt = <3700000>;
[all …]
Dapq8096-db820c.dtsi1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
12 #include <dt-bindings/sound/qcom,q6afe.h>
13 #include <dt-bindings/sound/qcom,q6asm.h>
27 * drawing no: LM25-P2751-1
38 * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
55 stdout-path = "serial0:115200n8";
[all …]
/kernel/linux/linux-4.19/Documentation/sound/soc/
Ddapm.rst8 Dynamic Audio Power Management (DAPM) is designed to allow portable
11 such, can easily co-exist with the other PM systems.
60 Audio DAPM widgets fall into a number of types:-
88 Regulator
89 External regulator that supplies power to audio components.
127 (Widgets are defined in include/sound/soc-dapm.h)
130 There are convenience macros defined in soc-dapm.h that can be used to quickly
138 ---------------------
144 Stream widgets have the following format:-
167 -------------------
[all …]
/kernel/linux/linux-5.10/Documentation/sound/soc/
Ddapm.rst8 Dynamic Audio Power Management (DAPM) is designed to allow portable
11 such, can easily co-exist with the other PM systems.
60 Audio DAPM widgets fall into a number of types:-
88 Regulator
89 External regulator that supplies power to audio components.
127 (Widgets are defined in include/sound/soc-dapm.h)
130 There are convenience macros defined in soc-dapm.h that can be used to quickly
138 ---------------------
144 Stream widgets have the following format:-
167 -------------------
[all …]
/kernel/linux/linux-5.10/sound/soc/codecs/
Dwm8955.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * wm8955.c -- WM8955 ALSA SoC Audio driver
17 #include <linux/regulator/consumer.h>
50 { 2, 0x0079 }, /* R2 - LOUT1 volume */
51 { 3, 0x0079 }, /* R3 - ROUT1 volume */
52 { 5, 0x0008 }, /* R5 - DAC Control */
53 { 7, 0x000A }, /* R7 - Audio Interface */
54 { 8, 0x0000 }, /* R8 - Sample Rate */
55 { 10, 0x00FF }, /* R10 - Left DAC volume */
56 { 11, 0x00FF }, /* R11 - Right DAC volume */
[all …]

123