• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1* ARM architected timer
2
3ARM cores may have a per-core architected timer, which provides per-cpu timers,
4or a memory mapped architected timer, which provides up to 8 frames with a
5physical and optional virtual timer per frame.
6
7The per-core architected timer is attached to a GIC to deliver its
8per-processor interrupts via PPIs. The memory mapped timer is attached to a GIC
9to deliver its interrupts via SPIs.
10
11** CP15 Timer node properties:
12
13- compatible : Should at least contain one of
14	"arm,armv7-timer"
15	"arm,armv8-timer"
16
17- interrupts : Interrupt list for secure, non-secure, virtual and
18  hypervisor timers, in that order.
19
20- clock-frequency : The frequency of the main counter, in Hz. Should be present
21  only where necessary to work around broken firmware which does not configure
22  CNTFRQ on all CPUs to a uniform correct value. Use of this property is
23  strongly discouraged; fix your firmware unless absolutely impossible.
24
25- always-on : a boolean property. If present, the timer is powered through an
26  always-on power domain, therefore it never loses context.
27
28- fsl,erratum-a008585 : A boolean property. Indicates the presence of
29  QorIQ erratum A-008585, which says that reading the counter is
30  unreliable unless the same value is returned by back-to-back reads.
31  This also affects writes to the tval register, due to the implicit
32  counter read.
33
34- hisilicon,erratum-161010101 : A boolean property. Indicates the
35  presence of Hisilicon erratum 161010101, which says that reading the
36  counters is unreliable in some cases, and reads may return a value 32
37  beyond the correct value. This also affects writes to the tval
38  registers, due to the implicit counter read.
39
40** Optional properties:
41
42- arm,cpu-registers-not-fw-configured : Firmware does not initialize
43  any of the generic timer CPU registers, which contain their
44  architecturally-defined reset values. Only supported for 32-bit
45  systems which follow the ARMv7 architected reset values.
46
47- arm,no-tick-in-suspend : The main counter does not tick when the system is in
48  low-power system suspend on some SoCs. This behavior does not match the
49  Architecture Reference Manual's specification that the system counter "must
50  be implemented in an always-on power domain."
51
52
53Example:
54
55	timer {
56		compatible = "arm,cortex-a15-timer",
57			     "arm,armv7-timer";
58		interrupts = <1 13 0xf08>,
59			     <1 14 0xf08>,
60			     <1 11 0xf08>,
61			     <1 10 0xf08>;
62		clock-frequency = <100000000>;
63	};
64
65** Memory mapped timer node properties:
66
67- compatible : Should at least contain "arm,armv7-timer-mem".
68
69- clock-frequency : The frequency of the main counter, in Hz. Should be present
70  only when firmware has not configured the MMIO CNTFRQ registers.
71
72- reg : The control frame base address.
73
74Note that #address-cells, #size-cells, and ranges shall be present to ensure
75the CPU can address a frame's registers.
76
77A timer node has up to 8 frame sub-nodes, each with the following properties:
78
79- frame-number: 0 to 7.
80
81- interrupts : Interrupt list for physical and virtual timers in that order.
82  The virtual timer interrupt is optional.
83
84- reg : The first and second view base addresses in that order. The second view
85  base address is optional.
86
87- status : "disabled" indicates the frame is not available for use. Optional.
88
89Example:
90
91	timer@f0000000 {
92		compatible = "arm,armv7-timer-mem";
93		#address-cells = <1>;
94		#size-cells = <1>;
95		ranges;
96		reg = <0xf0000000 0x1000>;
97		clock-frequency = <50000000>;
98
99		frame@f0001000 {
100			frame-number = <0>
101			interrupts = <0 13 0x8>,
102				     <0 14 0x8>;
103			reg = <0xf0001000 0x1000>,
104			      <0xf0002000 0x1000>;
105		};
106
107		frame@f0003000 {
108			frame-number = <1>
109			interrupts = <0 15 0x8>;
110			reg = <0xf0003000 0x1000>;
111		};
112	};
113