1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Samsung's Exynos4412 based Trats 2 board device tree source 4 * 5 * Copyright (c) 2013 Samsung Electronics Co., Ltd. 6 * http://www.samsung.com 7 * 8 * Device tree source file for Samsung's Trats 2 board which is based on 9 * Samsung's Exynos4412 SoC. 10 */ 11 12/dts-v1/; 13#include "exynos4412.dtsi" 14#include "exynos4412-ppmu-common.dtsi" 15#include <dt-bindings/gpio/gpio.h> 16#include <dt-bindings/interrupt-controller/irq.h> 17#include <dt-bindings/clock/maxim,max77686.h> 18#include <dt-bindings/pinctrl/samsung.h> 19 20/ { 21 compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4"; 22 23 aliases { 24 i2c11 = &i2c_max77693; 25 i2c12 = &i2c_max77693_fuel; 26 }; 27 28 chosen { 29 stdout-path = &serial_2; 30 }; 31 32 firmware@204f000 { 33 compatible = "samsung,secure-firmware"; 34 reg = <0x0204F000 0x1000>; 35 }; 36 37 fixed-rate-clocks { 38 xxti { 39 compatible = "samsung,clock-xxti", "fixed-clock"; 40 clock-frequency = <0>; 41 }; 42 43 xusbxti { 44 compatible = "samsung,clock-xusbxti", "fixed-clock"; 45 clock-frequency = <24000000>; 46 }; 47 }; 48 49 cam_io_reg: voltage-regulator-1 { 50 compatible = "regulator-fixed"; 51 regulator-name = "CAM_SENSOR_A"; 52 regulator-min-microvolt = <2800000>; 53 regulator-max-microvolt = <2800000>; 54 enable-active-high; 55 status = "disabled"; 56 }; 57 58 cam_af_reg: voltage-regulator-2 { 59 compatible = "regulator-fixed"; 60 regulator-name = "CAM_AF"; 61 regulator-min-microvolt = <2800000>; 62 regulator-max-microvolt = <2800000>; 63 enable-active-high; 64 status = "disabled"; 65 }; 66 67 vsil12: voltage-regulator-3 { 68 compatible = "regulator-fixed"; 69 regulator-name = "VSIL_1.2V"; 70 regulator-min-microvolt = <1200000>; 71 regulator-max-microvolt = <1200000>; 72 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; 73 enable-active-high; 74 vin-supply = <&buck7_reg>; 75 }; 76 77 vcc33mhl: voltage-regulator-4 { 78 compatible = "regulator-fixed"; 79 regulator-name = "VCC_3.3_MHL"; 80 regulator-min-microvolt = <3300000>; 81 regulator-max-microvolt = <3300000>; 82 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; 83 enable-active-high; 84 }; 85 86 vcc18mhl: voltage-regulator-5 { 87 compatible = "regulator-fixed"; 88 regulator-name = "VCC_1.8_MHL"; 89 regulator-min-microvolt = <1800000>; 90 regulator-max-microvolt = <1800000>; 91 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; 92 enable-active-high; 93 }; 94 95 gpio-keys { 96 compatible = "gpio-keys"; 97 pinctrl-names = "default"; 98 pinctrl-0 = <&gpio_keys>; 99 100 key-down { 101 gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; 102 linux,code = <114>; 103 label = "volume down"; 104 debounce-interval = <10>; 105 }; 106 107 key-up { 108 gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; 109 linux,code = <115>; 110 label = "volume up"; 111 debounce-interval = <10>; 112 }; 113 114 key-power { 115 gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; 116 linux,code = <116>; 117 label = "power"; 118 debounce-interval = <10>; 119 wakeup-source; 120 }; 121 122 key-ok { 123 gpios = <&gpx0 1 GPIO_ACTIVE_LOW>; 124 linux,code = <139>; 125 label = "ok"; 126 debounce-interval = <10>; 127 wakeup-source; 128 }; 129 }; 130 131 i2c_max77693: i2c-gpio-1 { 132 compatible = "i2c-gpio"; 133 gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>; 134 i2c-gpio,delay-us = <2>; 135 #address-cells = <1>; 136 #size-cells = <0>; 137 status = "okay"; 138 139 max77693@66 { 140 compatible = "maxim,max77693"; 141 interrupt-parent = <&gpx1>; 142 interrupts = <5 IRQ_TYPE_EDGE_FALLING>; 143 pinctrl-names = "default"; 144 pinctrl-0 = <&max77693_irq>; 145 reg = <0x66>; 146 147 regulators { 148 esafeout1_reg: ESAFEOUT1 { 149 regulator-name = "ESAFEOUT1"; 150 }; 151 esafeout2_reg: ESAFEOUT2 { 152 regulator-name = "ESAFEOUT2"; 153 }; 154 charger_reg: CHARGER { 155 regulator-name = "CHARGER"; 156 regulator-min-microamp = <60000>; 157 regulator-max-microamp = <2580000>; 158 }; 159 }; 160 161 max77693_haptic { 162 compatible = "maxim,max77693-haptic"; 163 haptic-supply = <&ldo26_reg>; 164 pwms = <&pwm 0 38022 0>; 165 }; 166 167 charger { 168 compatible = "maxim,max77693-charger"; 169 170 maxim,constant-microvolt = <4350000>; 171 maxim,min-system-microvolt = <3600000>; 172 maxim,thermal-regulation-celsius = <100>; 173 maxim,battery-overcurrent-microamp = <3500000>; 174 maxim,charge-input-threshold-microvolt = <4300000>; 175 }; 176 }; 177 }; 178 179 i2c_max77693_fuel: i2c-gpio-3 { 180 compatible = "i2c-gpio"; 181 gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>, <&gpf1 4 GPIO_ACTIVE_HIGH>; 182 i2c-gpio,delay-us = <2>; 183 #address-cells = <1>; 184 #size-cells = <0>; 185 status = "okay"; 186 187 max77693-fuel-gauge@36 { 188 compatible = "maxim,max17047"; 189 interrupt-parent = <&gpx2>; 190 interrupts = <3 IRQ_TYPE_EDGE_FALLING>; 191 pinctrl-names = "default"; 192 pinctrl-0 = <&max77693_fuel_irq>; 193 reg = <0x36>; 194 195 maxim,over-heat-temp = <700>; 196 maxim,over-volt = <4500>; 197 }; 198 }; 199 200 i2c-mhl { 201 compatible = "i2c-gpio"; 202 gpios = <&gpf0 4 GPIO_ACTIVE_HIGH>, <&gpf0 6 GPIO_ACTIVE_HIGH>; 203 i2c-gpio,delay-us = <100>; 204 #address-cells = <1>; 205 #size-cells = <0>; 206 207 pinctrl-0 = <&i2c_mhl_bus>; 208 pinctrl-names = "default"; 209 status = "okay"; 210 211 sii9234: hdmi-bridge@39 { 212 compatible = "sil,sii9234"; 213 avcc33-supply = <&vcc33mhl>; 214 iovcc18-supply = <&vcc18mhl>; 215 avcc12-supply = <&vsil12>; 216 cvcc12-supply = <&vsil12>; 217 reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>; 218 interrupt-parent = <&gpf3>; 219 interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; 220 reg = <0x39>; 221 222 port { 223 mhl_to_hdmi: endpoint { 224 remote-endpoint = <&hdmi_to_mhl>; 225 }; 226 }; 227 }; 228 }; 229 230 wlan_pwrseq: sdhci3-pwrseq { 231 compatible = "mmc-pwrseq-simple"; 232 reset-gpios = <&gpj0 0 GPIO_ACTIVE_LOW>; 233 clocks = <&max77686 MAX77686_CLK_PMIC>; 234 clock-names = "ext_clock"; 235 }; 236 237 sound { 238 compatible = "samsung,trats2-audio"; 239 samsung,i2s-controller = <&i2s0>; 240 samsung,model = "Trats2"; 241 samsung,audio-codec = <&wm1811>; 242 samsung,audio-routing = 243 "SPK", "SPKOUTLN", 244 "SPK", "SPKOUTLP", 245 "SPK", "SPKOUTRN", 246 "SPK", "SPKOUTRP"; 247 }; 248 249 thermistor-ap { 250 compatible = "murata,ncp15wb473"; 251 pullup-uv = <1800000>; /* VCC_1.8V_AP */ 252 pullup-ohm = <100000>; /* 100K */ 253 pulldown-ohm = <100000>; /* 100K */ 254 io-channels = <&adc 1>; /* AP temperature */ 255 }; 256 257 thermistor-battery { 258 compatible = "murata,ncp15wb473"; 259 pullup-uv = <1800000>; /* VCC_1.8V_AP */ 260 pullup-ohm = <100000>; /* 100K */ 261 pulldown-ohm = <100000>; /* 100K */ 262 io-channels = <&adc 2>; /* Battery temperature */ 263 }; 264 265 thermal-zones { 266 cpu_thermal: cpu-thermal { 267 cooling-maps { 268 map0 { 269 /* Corresponds to 800MHz at freq_table */ 270 cooling-device = <&cpu0 7 7>; 271 }; 272 map1 { 273 /* Corresponds to 200MHz at freq_table */ 274 cooling-device = <&cpu0 13 13>; 275 }; 276 }; 277 }; 278 }; 279}; 280 281&adc { 282 vdd-supply = <&ldo3_reg>; 283 status = "okay"; 284}; 285 286&bus_dmc { 287 devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; 288 vdd-supply = <&buck1_reg>; 289 status = "okay"; 290}; 291 292&bus_acp { 293 devfreq = <&bus_dmc>; 294 status = "okay"; 295}; 296 297&bus_c2c { 298 devfreq = <&bus_dmc>; 299 status = "okay"; 300}; 301 302&bus_leftbus { 303 devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; 304 vdd-supply = <&buck3_reg>; 305 status = "okay"; 306}; 307 308&bus_rightbus { 309 devfreq = <&bus_leftbus>; 310 status = "okay"; 311}; 312 313&bus_display { 314 devfreq = <&bus_leftbus>; 315 status = "okay"; 316}; 317 318&bus_fsys { 319 devfreq = <&bus_leftbus>; 320 status = "okay"; 321}; 322 323&bus_peri { 324 devfreq = <&bus_leftbus>; 325 status = "okay"; 326}; 327 328&bus_mfc { 329 devfreq = <&bus_leftbus>; 330 status = "okay"; 331}; 332 333&camera { 334 pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>; 335 pinctrl-names = "default"; 336 status = "okay"; 337 assigned-clocks = <&clock CLK_MOUT_CAM0>, 338 <&clock CLK_MOUT_CAM1>; 339 assigned-clock-parents = <&clock CLK_XUSBXTI>, 340 <&clock CLK_XUSBXTI>; 341}; 342 343&cpu0 { 344 cpu0-supply = <&buck2_reg>; 345}; 346 347&csis_0 { 348 status = "okay"; 349 vddcore-supply = <&ldo8_reg>; 350 vddio-supply = <&ldo10_reg>; 351 assigned-clocks = <&clock CLK_MOUT_CSIS0>, 352 <&clock CLK_SCLK_CSIS0>; 353 assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; 354 assigned-clock-rates = <0>, <176000000>; 355 356 /* Camera C (3) MIPI CSI-2 (CSIS0) */ 357 port@3 { 358 reg = <3>; 359 csis0_ep: endpoint { 360 remote-endpoint = <&s5c73m3_ep>; 361 data-lanes = <1 2 3 4>; 362 samsung,csis-hs-settle = <12>; 363 }; 364 }; 365}; 366 367&csis_1 { 368 status = "okay"; 369 vddcore-supply = <&ldo8_reg>; 370 vddio-supply = <&ldo10_reg>; 371 assigned-clocks = <&clock CLK_MOUT_CSIS1>, 372 <&clock CLK_SCLK_CSIS1>; 373 assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; 374 assigned-clock-rates = <0>, <176000000>; 375 376 /* Camera D (4) MIPI CSI-2 (CSIS1) */ 377 port@4 { 378 reg = <4>; 379 csis1_ep: endpoint { 380 remote-endpoint = <&is_s5k6a3_ep>; 381 data-lanes = <1>; 382 samsung,csis-hs-settle = <18>; 383 samsung,csis-wclk; 384 }; 385 }; 386}; 387 388&dsi_0 { 389 vddcore-supply = <&ldo8_reg>; 390 vddio-supply = <&ldo10_reg>; 391 samsung,burst-clock-frequency = <500000000>; 392 samsung,esc-clock-frequency = <20000000>; 393 samsung,pll-clock-frequency = <24000000>; 394}; 395 396&exynos_usbphy { 397 vbus-supply = <&esafeout1_reg>; 398 status = "okay"; 399}; 400 401&fimc_0 { 402 status = "okay"; 403 assigned-clocks = <&clock CLK_MOUT_FIMC0>, 404 <&clock CLK_SCLK_FIMC0>; 405 assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; 406 assigned-clock-rates = <0>, <176000000>; 407}; 408 409&fimc_1 { 410 status = "okay"; 411 assigned-clocks = <&clock CLK_MOUT_FIMC1>, 412 <&clock CLK_SCLK_FIMC1>; 413 assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; 414 assigned-clock-rates = <0>, <176000000>; 415}; 416 417&fimc_2 { 418 status = "okay"; 419 assigned-clocks = <&clock CLK_MOUT_FIMC2>, 420 <&clock CLK_SCLK_FIMC2>; 421 assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; 422 assigned-clock-rates = <0>, <176000000>; 423}; 424 425&fimc_3 { 426 status = "okay"; 427 assigned-clocks = <&clock CLK_MOUT_FIMC3>, 428 <&clock CLK_SCLK_FIMC3>; 429 assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; 430 assigned-clock-rates = <0>, <176000000>; 431}; 432 433&fimc_is { 434 pinctrl-0 = <&fimc_is_uart>; 435 pinctrl-names = "default"; 436 status = "okay"; 437 438 }; 439 440&fimc_lite_0 { 441 status = "okay"; 442}; 443 444&fimc_lite_1 { 445 status = "okay"; 446}; 447 448&fimd { 449 status = "okay"; 450}; 451 452&hdmi { 453 hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>; 454 pinctrl-names = "default"; 455 pinctrl-0 = <&hdmi_hpd>; 456 vdd-supply = <&ldo3_reg>; 457 vdd_osc-supply = <&ldo4_reg>; 458 vdd_pll-supply = <&ldo3_reg>; 459 ddc = <&i2c_5>; 460 status = "okay"; 461 462 ports { 463 #address-cells = <1>; 464 #size-cells = <0>; 465 466 port@1 { 467 reg = <1>; 468 hdmi_to_mhl: endpoint { 469 remote-endpoint = <&mhl_to_hdmi>; 470 }; 471 }; 472 }; 473}; 474 475&hsotg { 476 vusb_d-supply = <&ldo15_reg>; 477 vusb_a-supply = <&ldo12_reg>; 478 dr_mode = "peripheral"; 479 status = "okay"; 480}; 481 482&i2c_0 { 483 samsung,i2c-sda-delay = <100>; 484 samsung,i2c-slave-addr = <0x10>; 485 samsung,i2c-max-bus-freq = <400000>; 486 pinctrl-0 = <&i2c0_bus>; 487 pinctrl-names = "default"; 488 status = "okay"; 489 490 s5c73m3: s5c73m3@3c { 491 compatible = "samsung,s5c73m3"; 492 reg = <0x3c>; 493 xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */ 494 vdd-int-supply = <&buck9_reg>; 495 vddio-cis-supply = <&ldo9_reg>; 496 vddio-host-supply = <&ldo18_reg>; 497 vdd-af-supply = <&cam_af_reg>; 498 vdd-reg-supply = <&cam_io_reg>; 499 clock-frequency = <24000000>; 500 /* CAM_A_CLKOUT */ 501 clocks = <&camera 0>; 502 clock-names = "cis_extclk"; 503 status = "disabled"; 504 port { 505 s5c73m3_ep: endpoint { 506 remote-endpoint = <&csis0_ep>; 507 data-lanes = <1 2 3 4>; 508 }; 509 }; 510 }; 511}; 512 513&i2c1_isp { 514 pinctrl-0 = <&fimc_is_i2c1>; 515 pinctrl-names = "default"; 516 517 s5k6a3@10 { 518 compatible = "samsung,s5k6a3"; 519 reg = <0x10>; 520 svdda-supply = <&cam_io_reg>; 521 svddio-supply = <&ldo19_reg>; 522 afvdd-supply = <&ldo19_reg>; 523 clock-frequency = <24000000>; 524 /* CAM_B_CLKOUT */ 525 clocks = <&camera 1>; 526 clock-names = "extclk"; 527 samsung,camclk-out = <1>; 528 gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>; 529 530 port { 531 is_s5k6a3_ep: endpoint { 532 remote-endpoint = <&csis1_ep>; 533 data-lanes = <1>; 534 }; 535 }; 536 }; 537}; 538 539&i2c_3 { 540 samsung,i2c-sda-delay = <100>; 541 samsung,i2c-slave-addr = <0x10>; 542 samsung,i2c-max-bus-freq = <400000>; 543 pinctrl-0 = <&i2c3_bus>; 544 pinctrl-names = "default"; 545 status = "okay"; 546}; 547 548&i2c_4 { 549 samsung,i2c-sda-delay = <100>; 550 samsung,i2c-slave-addr = <0x10>; 551 samsung,i2c-max-bus-freq = <100000>; 552 pinctrl-0 = <&i2c4_bus>; 553 pinctrl-names = "default"; 554 status = "okay"; 555 556 wm1811: wm1811@1a { 557 compatible = "wlf,wm1811"; 558 reg = <0x1a>; 559 clocks = <&pmu_system_controller 0>; 560 clock-names = "MCLK1"; 561 DCVDD-supply = <&ldo3_reg>; 562 DBVDD1-supply = <&ldo3_reg>; 563 wlf,ldo1ena = <&gpj0 4 0>; 564 }; 565}; 566 567&i2c_5 { 568 status = "okay"; 569}; 570 571&i2c_7 { 572 samsung,i2c-sda-delay = <100>; 573 samsung,i2c-slave-addr = <0x10>; 574 samsung,i2c-max-bus-freq = <100000>; 575 pinctrl-0 = <&i2c7_bus>; 576 pinctrl-names = "default"; 577 status = "okay"; 578 579 max77686: max77686_pmic@9 { 580 compatible = "maxim,max77686"; 581 interrupt-parent = <&gpx0>; 582 interrupts = <7 IRQ_TYPE_NONE>; 583 pinctrl-0 = <&max77686_irq>; 584 pinctrl-names = "default"; 585 reg = <0x09>; 586 #clock-cells = <1>; 587 588 voltage-regulators { 589 ldo1_reg: LDO1 { 590 regulator-name = "VALIVE_1.0V_AP"; 591 regulator-min-microvolt = <1000000>; 592 regulator-max-microvolt = <1000000>; 593 regulator-always-on; 594 }; 595 596 ldo2_reg: LDO2 { 597 regulator-name = "VM1M2_1.2V_AP"; 598 regulator-min-microvolt = <1200000>; 599 regulator-max-microvolt = <1200000>; 600 regulator-always-on; 601 regulator-state-mem { 602 regulator-on-in-suspend; 603 }; 604 }; 605 606 ldo3_reg: LDO3 { 607 regulator-name = "VCC_1.8V_AP"; 608 regulator-min-microvolt = <1800000>; 609 regulator-max-microvolt = <1800000>; 610 regulator-always-on; 611 }; 612 613 ldo4_reg: LDO4 { 614 regulator-name = "VCC_2.8V_AP"; 615 regulator-min-microvolt = <2800000>; 616 regulator-max-microvolt = <2800000>; 617 regulator-always-on; 618 }; 619 620 ldo5_reg: LDO5 { 621 regulator-name = "VCC_1.8V_IO"; 622 regulator-min-microvolt = <1800000>; 623 regulator-max-microvolt = <1800000>; 624 regulator-always-on; 625 }; 626 627 ldo6_reg: LDO6 { 628 regulator-name = "VMPLL_1.0V_AP"; 629 regulator-min-microvolt = <1000000>; 630 regulator-max-microvolt = <1000000>; 631 regulator-always-on; 632 regulator-state-mem { 633 regulator-on-in-suspend; 634 }; 635 }; 636 637 ldo7_reg: LDO7 { 638 regulator-name = "VPLL_1.0V_AP"; 639 regulator-min-microvolt = <1000000>; 640 regulator-max-microvolt = <1000000>; 641 regulator-always-on; 642 regulator-state-mem { 643 regulator-on-in-suspend; 644 }; 645 }; 646 647 ldo8_reg: LDO8 { 648 regulator-name = "VMIPI_1.0V"; 649 regulator-min-microvolt = <1000000>; 650 regulator-max-microvolt = <1000000>; 651 regulator-state-mem { 652 regulator-off-in-suspend; 653 }; 654 }; 655 656 ldo9_reg: LDO9 { 657 regulator-name = "CAM_ISP_MIPI_1.2V"; 658 regulator-min-microvolt = <1200000>; 659 regulator-max-microvolt = <1200000>; 660 }; 661 662 ldo10_reg: LDO10 { 663 regulator-name = "VMIPI_1.8V"; 664 regulator-min-microvolt = <1800000>; 665 regulator-max-microvolt = <1800000>; 666 regulator-state-mem { 667 regulator-off-in-suspend; 668 }; 669 }; 670 671 ldo11_reg: LDO11 { 672 regulator-name = "VABB1_1.95V"; 673 regulator-min-microvolt = <1950000>; 674 regulator-max-microvolt = <1950000>; 675 regulator-always-on; 676 regulator-state-mem { 677 regulator-off-in-suspend; 678 }; 679 }; 680 681 ldo12_reg: LDO12 { 682 regulator-name = "VUOTG_3.0V"; 683 regulator-min-microvolt = <3000000>; 684 regulator-max-microvolt = <3000000>; 685 regulator-state-mem { 686 regulator-off-in-suspend; 687 }; 688 }; 689 690 ldo13_reg: LDO13 { 691 regulator-name = "NFC_AVDD_1.8V"; 692 regulator-min-microvolt = <1800000>; 693 regulator-max-microvolt = <1800000>; 694 }; 695 696 ldo14_reg: LDO14 { 697 regulator-name = "VABB2_1.95V"; 698 regulator-min-microvolt = <1950000>; 699 regulator-max-microvolt = <1950000>; 700 regulator-always-on; 701 regulator-state-mem { 702 regulator-off-in-suspend; 703 }; 704 }; 705 706 ldo15_reg: LDO15 { 707 regulator-name = "VHSIC_1.0V"; 708 regulator-min-microvolt = <1000000>; 709 regulator-max-microvolt = <1000000>; 710 regulator-state-mem { 711 regulator-on-in-suspend; 712 }; 713 }; 714 715 ldo16_reg: LDO16 { 716 regulator-name = "VHSIC_1.8V"; 717 regulator-min-microvolt = <1800000>; 718 regulator-max-microvolt = <1800000>; 719 regulator-state-mem { 720 regulator-on-in-suspend; 721 }; 722 }; 723 724 ldo17_reg: LDO17 { 725 regulator-name = "CAM_SENSOR_CORE_1.2V"; 726 regulator-min-microvolt = <1200000>; 727 regulator-max-microvolt = <1200000>; 728 }; 729 730 ldo18_reg: LDO18 { 731 regulator-name = "CAM_ISP_SEN_IO_1.8V"; 732 regulator-min-microvolt = <1800000>; 733 regulator-max-microvolt = <1800000>; 734 }; 735 736 ldo19_reg: LDO19 { 737 regulator-name = "VT_CAM_1.8V"; 738 regulator-min-microvolt = <1800000>; 739 regulator-max-microvolt = <1800000>; 740 }; 741 742 ldo20_reg: LDO20 { 743 regulator-name = "VDDQ_PRE_1.8V"; 744 regulator-min-microvolt = <1800000>; 745 regulator-max-microvolt = <1800000>; 746 }; 747 748 ldo21_reg: LDO21 { 749 regulator-name = "VTF_2.8V"; 750 regulator-min-microvolt = <2800000>; 751 regulator-max-microvolt = <2800000>; 752 maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; 753 }; 754 755 ldo22_reg: LDO22 { 756 regulator-name = "VMEM_VDD_2.8V"; 757 regulator-min-microvolt = <2800000>; 758 regulator-max-microvolt = <2800000>; 759 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; 760 }; 761 762 ldo23_reg: LDO23 { 763 regulator-name = "TSP_AVDD_3.3V"; 764 regulator-min-microvolt = <3300000>; 765 regulator-max-microvolt = <3300000>; 766 }; 767 768 ldo24_reg: LDO24 { 769 regulator-name = "TSP_VDD_1.8V"; 770 regulator-min-microvolt = <1800000>; 771 regulator-max-microvolt = <1800000>; 772 }; 773 774 ldo25_reg: LDO25 { 775 regulator-name = "LDO25"; 776 }; 777 778 ldo26_reg: LDO26 { 779 regulator-name = "MOTOR_VCC_3.0V"; 780 regulator-min-microvolt = <3000000>; 781 regulator-max-microvolt = <3000000>; 782 }; 783 784 buck1_reg: BUCK1 { 785 regulator-name = "vdd_mif"; 786 regulator-min-microvolt = <850000>; 787 regulator-max-microvolt = <1100000>; 788 regulator-always-on; 789 regulator-boot-on; 790 regulator-state-mem { 791 regulator-off-in-suspend; 792 }; 793 }; 794 795 buck2_reg: BUCK2 { 796 regulator-name = "vdd_arm"; 797 regulator-min-microvolt = <850000>; 798 regulator-max-microvolt = <1500000>; 799 regulator-always-on; 800 regulator-boot-on; 801 regulator-state-mem { 802 regulator-on-in-suspend; 803 }; 804 }; 805 806 buck3_reg: BUCK3 { 807 regulator-name = "vdd_int"; 808 regulator-min-microvolt = <850000>; 809 regulator-max-microvolt = <1150000>; 810 regulator-always-on; 811 regulator-boot-on; 812 regulator-state-mem { 813 regulator-off-in-suspend; 814 }; 815 }; 816 817 buck4_reg: BUCK4 { 818 regulator-name = "vdd_g3d"; 819 regulator-min-microvolt = <850000>; 820 regulator-max-microvolt = <1150000>; 821 regulator-boot-on; 822 regulator-state-mem { 823 regulator-off-in-suspend; 824 }; 825 }; 826 827 buck5_reg: BUCK5 { 828 regulator-name = "VMEM_1.2V_AP"; 829 regulator-min-microvolt = <1200000>; 830 regulator-max-microvolt = <1200000>; 831 regulator-always-on; 832 }; 833 834 buck6_reg: BUCK6 { 835 regulator-name = "VCC_SUB_1.35V"; 836 regulator-min-microvolt = <1350000>; 837 regulator-max-microvolt = <1350000>; 838 regulator-always-on; 839 }; 840 841 buck7_reg: BUCK7 { 842 regulator-name = "VCC_SUB_2.0V"; 843 regulator-min-microvolt = <2000000>; 844 regulator-max-microvolt = <2000000>; 845 regulator-always-on; 846 }; 847 848 buck8_reg: BUCK8 { 849 regulator-name = "VMEM_VDDF_3.0V"; 850 regulator-min-microvolt = <2850000>; 851 regulator-max-microvolt = <2850000>; 852 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; 853 }; 854 855 buck9_reg: BUCK9 { 856 regulator-name = "CAM_ISP_CORE_1.2V"; 857 regulator-min-microvolt = <1000000>; 858 regulator-max-microvolt = <1200000>; 859 }; 860 }; 861 }; 862}; 863 864&i2c_8 { 865 status = "okay"; 866}; 867 868&i2s0 { 869 pinctrl-0 = <&i2s0_bus>; 870 pinctrl-names = "default"; 871 status = "okay"; 872}; 873 874&mixer { 875 status = "okay"; 876}; 877 878&mshc_0 { 879 broken-cd; 880 non-removable; 881 card-detect-delay = <200>; 882 vmmc-supply = <&ldo22_reg>; 883 clock-frequency = <400000000>; 884 samsung,dw-mshc-ciu-div = <0>; 885 samsung,dw-mshc-sdr-timing = <2 3>; 886 samsung,dw-mshc-ddr-timing = <1 2>; 887 pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; 888 pinctrl-names = "default"; 889 status = "okay"; 890 bus-width = <8>; 891 cap-mmc-highspeed; 892}; 893 894&pmu_system_controller { 895 assigned-clocks = <&pmu_system_controller 0>; 896 assigned-clock-parents = <&clock CLK_XUSBXTI>; 897}; 898 899&pinctrl_0 { 900 pinctrl-names = "default"; 901 pinctrl-0 = <&sleep0>; 902 903 mhl_int: mhl-int { 904 samsung,pins = "gpf3-5"; 905 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; 906 }; 907 908 i2c_mhl_bus: i2c-mhl-bus { 909 samsung,pins = "gpf0-4", "gpf0-6"; 910 samsung,pin-function = <EXYNOS_PIN_FUNC_2>; 911 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; 912 samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; 913 }; 914 915 sleep0: sleep-states { 916 PIN_SLP(gpa0-0, INPUT, NONE); 917 PIN_SLP(gpa0-1, OUT0, NONE); 918 PIN_SLP(gpa0-2, INPUT, NONE); 919 PIN_SLP(gpa0-3, INPUT, UP); 920 PIN_SLP(gpa0-4, INPUT, NONE); 921 PIN_SLP(gpa0-5, INPUT, DOWN); 922 PIN_SLP(gpa0-6, INPUT, DOWN); 923 PIN_SLP(gpa0-7, INPUT, UP); 924 925 PIN_SLP(gpa1-0, INPUT, DOWN); 926 PIN_SLP(gpa1-1, INPUT, DOWN); 927 PIN_SLP(gpa1-2, INPUT, DOWN); 928 PIN_SLP(gpa1-3, INPUT, DOWN); 929 PIN_SLP(gpa1-4, INPUT, DOWN); 930 PIN_SLP(gpa1-5, INPUT, DOWN); 931 932 PIN_SLP(gpb-0, INPUT, NONE); 933 PIN_SLP(gpb-1, INPUT, NONE); 934 PIN_SLP(gpb-2, INPUT, NONE); 935 PIN_SLP(gpb-3, INPUT, NONE); 936 PIN_SLP(gpb-4, INPUT, DOWN); 937 PIN_SLP(gpb-5, INPUT, UP); 938 PIN_SLP(gpb-6, INPUT, DOWN); 939 PIN_SLP(gpb-7, INPUT, DOWN); 940 941 PIN_SLP(gpc0-0, INPUT, DOWN); 942 PIN_SLP(gpc0-1, INPUT, DOWN); 943 PIN_SLP(gpc0-2, INPUT, DOWN); 944 PIN_SLP(gpc0-3, INPUT, DOWN); 945 PIN_SLP(gpc0-4, INPUT, DOWN); 946 947 PIN_SLP(gpc1-0, INPUT, NONE); 948 PIN_SLP(gpc1-1, PREV, NONE); 949 PIN_SLP(gpc1-2, INPUT, NONE); 950 PIN_SLP(gpc1-3, INPUT, NONE); 951 PIN_SLP(gpc1-4, INPUT, NONE); 952 953 PIN_SLP(gpd0-0, INPUT, DOWN); 954 PIN_SLP(gpd0-1, INPUT, DOWN); 955 PIN_SLP(gpd0-2, INPUT, NONE); 956 PIN_SLP(gpd0-3, INPUT, NONE); 957 958 PIN_SLP(gpd1-0, INPUT, DOWN); 959 PIN_SLP(gpd1-1, INPUT, DOWN); 960 PIN_SLP(gpd1-2, INPUT, NONE); 961 PIN_SLP(gpd1-3, INPUT, NONE); 962 963 PIN_SLP(gpf0-0, INPUT, NONE); 964 PIN_SLP(gpf0-1, INPUT, NONE); 965 PIN_SLP(gpf0-2, INPUT, DOWN); 966 PIN_SLP(gpf0-3, INPUT, DOWN); 967 PIN_SLP(gpf0-4, INPUT, NONE); 968 PIN_SLP(gpf0-5, INPUT, DOWN); 969 PIN_SLP(gpf0-6, INPUT, NONE); 970 PIN_SLP(gpf0-7, INPUT, DOWN); 971 972 PIN_SLP(gpf1-0, INPUT, DOWN); 973 PIN_SLP(gpf1-1, INPUT, DOWN); 974 PIN_SLP(gpf1-2, INPUT, DOWN); 975 PIN_SLP(gpf1-3, INPUT, DOWN); 976 PIN_SLP(gpf1-4, INPUT, NONE); 977 PIN_SLP(gpf1-5, INPUT, NONE); 978 PIN_SLP(gpf1-6, INPUT, DOWN); 979 PIN_SLP(gpf1-7, PREV, NONE); 980 981 PIN_SLP(gpf2-0, PREV, NONE); 982 PIN_SLP(gpf2-1, INPUT, DOWN); 983 PIN_SLP(gpf2-2, INPUT, DOWN); 984 PIN_SLP(gpf2-3, INPUT, DOWN); 985 PIN_SLP(gpf2-4, INPUT, DOWN); 986 PIN_SLP(gpf2-5, INPUT, DOWN); 987 PIN_SLP(gpf2-6, INPUT, NONE); 988 PIN_SLP(gpf2-7, INPUT, NONE); 989 990 PIN_SLP(gpf3-0, INPUT, NONE); 991 PIN_SLP(gpf3-1, PREV, NONE); 992 PIN_SLP(gpf3-2, PREV, NONE); 993 PIN_SLP(gpf3-3, PREV, NONE); 994 PIN_SLP(gpf3-4, OUT1, NONE); 995 PIN_SLP(gpf3-5, INPUT, DOWN); 996 997 PIN_SLP(gpj0-0, PREV, NONE); 998 PIN_SLP(gpj0-1, PREV, NONE); 999 PIN_SLP(gpj0-2, PREV, NONE); 1000 PIN_SLP(gpj0-3, INPUT, DOWN); 1001 PIN_SLP(gpj0-4, PREV, NONE); 1002 PIN_SLP(gpj0-5, PREV, NONE); 1003 PIN_SLP(gpj0-6, INPUT, DOWN); 1004 PIN_SLP(gpj0-7, INPUT, DOWN); 1005 1006 PIN_SLP(gpj1-0, INPUT, DOWN); 1007 PIN_SLP(gpj1-1, PREV, NONE); 1008 PIN_SLP(gpj1-2, PREV, NONE); 1009 PIN_SLP(gpj1-3, INPUT, DOWN); 1010 PIN_SLP(gpj1-4, INPUT, DOWN); 1011 }; 1012}; 1013 1014&pinctrl_1 { 1015 pinctrl-names = "default"; 1016 pinctrl-0 = <&sleep1>; 1017 1018 gpio_keys: gpio-keys { 1019 samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3"; 1020 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; 1021 }; 1022 1023 max77686_irq: max77686-irq { 1024 samsung,pins = "gpx0-7"; 1025 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; 1026 }; 1027 1028 max77693_irq: max77693-irq { 1029 samsung,pins = "gpx1-5"; 1030 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; 1031 }; 1032 1033 max77693_fuel_irq: max77693-fuel-irq { 1034 samsung,pins = "gpx2-3"; 1035 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; 1036 }; 1037 1038 sdhci2_cd: sdhci2-cd-irq { 1039 samsung,pins = "gpx3-4"; 1040 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; 1041 }; 1042 1043 hdmi_hpd: hdmi-hpd { 1044 samsung,pins = "gpx3-7"; 1045 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; 1046 }; 1047 1048 sleep1: sleep-states { 1049 PIN_SLP(gpk0-0, PREV, NONE); 1050 PIN_SLP(gpk0-1, PREV, NONE); 1051 PIN_SLP(gpk0-2, OUT0, NONE); 1052 PIN_SLP(gpk0-3, PREV, NONE); 1053 PIN_SLP(gpk0-4, PREV, NONE); 1054 PIN_SLP(gpk0-5, PREV, NONE); 1055 PIN_SLP(gpk0-6, PREV, NONE); 1056 1057 PIN_SLP(gpk1-0, INPUT, DOWN); 1058 PIN_SLP(gpk1-1, INPUT, DOWN); 1059 PIN_SLP(gpk1-2, INPUT, DOWN); 1060 PIN_SLP(gpk1-3, PREV, NONE); 1061 PIN_SLP(gpk1-4, PREV, NONE); 1062 PIN_SLP(gpk1-5, PREV, NONE); 1063 PIN_SLP(gpk1-6, PREV, NONE); 1064 1065 PIN_SLP(gpk2-0, INPUT, DOWN); 1066 PIN_SLP(gpk2-1, INPUT, DOWN); 1067 PIN_SLP(gpk2-2, INPUT, DOWN); 1068 PIN_SLP(gpk2-3, INPUT, DOWN); 1069 PIN_SLP(gpk2-4, INPUT, DOWN); 1070 PIN_SLP(gpk2-5, INPUT, DOWN); 1071 PIN_SLP(gpk2-6, INPUT, DOWN); 1072 1073 PIN_SLP(gpk3-0, OUT0, NONE); 1074 PIN_SLP(gpk3-1, INPUT, NONE); 1075 PIN_SLP(gpk3-2, INPUT, DOWN); 1076 PIN_SLP(gpk3-3, INPUT, NONE); 1077 PIN_SLP(gpk3-4, INPUT, NONE); 1078 PIN_SLP(gpk3-5, INPUT, NONE); 1079 PIN_SLP(gpk3-6, INPUT, NONE); 1080 1081 PIN_SLP(gpl0-0, INPUT, DOWN); 1082 PIN_SLP(gpl0-1, INPUT, DOWN); 1083 PIN_SLP(gpl0-2, INPUT, DOWN); 1084 PIN_SLP(gpl0-3, INPUT, DOWN); 1085 PIN_SLP(gpl0-4, PREV, NONE); 1086 PIN_SLP(gpl0-6, PREV, NONE); 1087 1088 PIN_SLP(gpl1-0, INPUT, DOWN); 1089 PIN_SLP(gpl1-1, INPUT, DOWN); 1090 PIN_SLP(gpl2-0, INPUT, DOWN); 1091 PIN_SLP(gpl2-1, INPUT, DOWN); 1092 PIN_SLP(gpl2-2, INPUT, DOWN); 1093 PIN_SLP(gpl2-3, INPUT, DOWN); 1094 PIN_SLP(gpl2-4, INPUT, DOWN); 1095 PIN_SLP(gpl2-5, INPUT, DOWN); 1096 PIN_SLP(gpl2-6, PREV, NONE); 1097 PIN_SLP(gpl2-7, INPUT, DOWN); 1098 1099 PIN_SLP(gpm0-0, INPUT, DOWN); 1100 PIN_SLP(gpm0-1, INPUT, DOWN); 1101 PIN_SLP(gpm0-2, INPUT, DOWN); 1102 PIN_SLP(gpm0-3, INPUT, DOWN); 1103 PIN_SLP(gpm0-4, INPUT, DOWN); 1104 PIN_SLP(gpm0-5, INPUT, DOWN); 1105 PIN_SLP(gpm0-6, INPUT, DOWN); 1106 PIN_SLP(gpm0-7, INPUT, DOWN); 1107 1108 PIN_SLP(gpm1-0, INPUT, DOWN); 1109 PIN_SLP(gpm1-1, INPUT, DOWN); 1110 PIN_SLP(gpm1-2, INPUT, NONE); 1111 PIN_SLP(gpm1-3, INPUT, NONE); 1112 PIN_SLP(gpm1-4, INPUT, NONE); 1113 PIN_SLP(gpm1-5, INPUT, NONE); 1114 PIN_SLP(gpm1-6, INPUT, DOWN); 1115 1116 PIN_SLP(gpm2-0, INPUT, NONE); 1117 PIN_SLP(gpm2-1, INPUT, NONE); 1118 PIN_SLP(gpm2-2, INPUT, DOWN); 1119 PIN_SLP(gpm2-3, INPUT, DOWN); 1120 PIN_SLP(gpm2-4, INPUT, DOWN); 1121 1122 PIN_SLP(gpm3-0, PREV, NONE); 1123 PIN_SLP(gpm3-1, PREV, NONE); 1124 PIN_SLP(gpm3-2, PREV, NONE); 1125 PIN_SLP(gpm3-3, OUT1, NONE); 1126 PIN_SLP(gpm3-4, INPUT, DOWN); 1127 PIN_SLP(gpm3-5, INPUT, DOWN); 1128 PIN_SLP(gpm3-6, INPUT, DOWN); 1129 PIN_SLP(gpm3-7, INPUT, DOWN); 1130 1131 PIN_SLP(gpm4-0, INPUT, DOWN); 1132 PIN_SLP(gpm4-1, INPUT, DOWN); 1133 PIN_SLP(gpm4-2, INPUT, DOWN); 1134 PIN_SLP(gpm4-3, INPUT, DOWN); 1135 PIN_SLP(gpm4-4, INPUT, DOWN); 1136 PIN_SLP(gpm4-5, INPUT, DOWN); 1137 PIN_SLP(gpm4-6, INPUT, DOWN); 1138 PIN_SLP(gpm4-7, INPUT, DOWN); 1139 1140 PIN_SLP(gpy0-0, INPUT, DOWN); 1141 PIN_SLP(gpy0-1, INPUT, DOWN); 1142 PIN_SLP(gpy0-2, INPUT, DOWN); 1143 PIN_SLP(gpy0-3, INPUT, DOWN); 1144 PIN_SLP(gpy0-4, INPUT, DOWN); 1145 PIN_SLP(gpy0-5, INPUT, DOWN); 1146 1147 PIN_SLP(gpy1-0, INPUT, DOWN); 1148 PIN_SLP(gpy1-1, INPUT, DOWN); 1149 PIN_SLP(gpy1-2, INPUT, DOWN); 1150 PIN_SLP(gpy1-3, INPUT, DOWN); 1151 1152 PIN_SLP(gpy2-0, PREV, NONE); 1153 PIN_SLP(gpy2-1, INPUT, DOWN); 1154 PIN_SLP(gpy2-2, INPUT, NONE); 1155 PIN_SLP(gpy2-3, INPUT, NONE); 1156 PIN_SLP(gpy2-4, INPUT, NONE); 1157 PIN_SLP(gpy2-5, INPUT, NONE); 1158 1159 PIN_SLP(gpy3-0, INPUT, DOWN); 1160 PIN_SLP(gpy3-1, INPUT, DOWN); 1161 PIN_SLP(gpy3-2, INPUT, DOWN); 1162 PIN_SLP(gpy3-3, INPUT, DOWN); 1163 PIN_SLP(gpy3-4, INPUT, DOWN); 1164 PIN_SLP(gpy3-5, INPUT, DOWN); 1165 PIN_SLP(gpy3-6, INPUT, DOWN); 1166 PIN_SLP(gpy3-7, INPUT, DOWN); 1167 1168 PIN_SLP(gpy4-0, INPUT, DOWN); 1169 PIN_SLP(gpy4-1, INPUT, DOWN); 1170 PIN_SLP(gpy4-2, INPUT, DOWN); 1171 PIN_SLP(gpy4-3, INPUT, DOWN); 1172 PIN_SLP(gpy4-4, INPUT, DOWN); 1173 PIN_SLP(gpy4-5, INPUT, DOWN); 1174 PIN_SLP(gpy4-6, INPUT, DOWN); 1175 PIN_SLP(gpy4-7, INPUT, DOWN); 1176 1177 PIN_SLP(gpy5-0, INPUT, DOWN); 1178 PIN_SLP(gpy5-1, INPUT, DOWN); 1179 PIN_SLP(gpy5-2, INPUT, DOWN); 1180 PIN_SLP(gpy5-3, INPUT, DOWN); 1181 PIN_SLP(gpy5-4, INPUT, DOWN); 1182 PIN_SLP(gpy5-5, INPUT, DOWN); 1183 PIN_SLP(gpy5-6, INPUT, DOWN); 1184 PIN_SLP(gpy5-7, INPUT, DOWN); 1185 1186 PIN_SLP(gpy6-0, INPUT, DOWN); 1187 PIN_SLP(gpy6-1, INPUT, DOWN); 1188 PIN_SLP(gpy6-2, INPUT, DOWN); 1189 PIN_SLP(gpy6-3, INPUT, DOWN); 1190 PIN_SLP(gpy6-4, INPUT, DOWN); 1191 PIN_SLP(gpy6-5, INPUT, DOWN); 1192 PIN_SLP(gpy6-6, INPUT, DOWN); 1193 PIN_SLP(gpy6-7, INPUT, DOWN); 1194 }; 1195}; 1196 1197&pinctrl_2 { 1198 pinctrl-names = "default"; 1199 pinctrl-0 = <&sleep2>; 1200 1201 sleep2: sleep-states { 1202 PIN_SLP(gpz-0, INPUT, DOWN); 1203 PIN_SLP(gpz-1, INPUT, DOWN); 1204 PIN_SLP(gpz-2, INPUT, DOWN); 1205 PIN_SLP(gpz-3, INPUT, DOWN); 1206 PIN_SLP(gpz-4, INPUT, DOWN); 1207 PIN_SLP(gpz-5, INPUT, DOWN); 1208 PIN_SLP(gpz-6, INPUT, DOWN); 1209 }; 1210}; 1211 1212&pinctrl_3 { 1213 pinctrl-names = "default"; 1214 pinctrl-0 = <&sleep3>; 1215 1216 sleep3: sleep-states { 1217 PIN_SLP(gpv0-0, INPUT, DOWN); 1218 PIN_SLP(gpv0-1, INPUT, DOWN); 1219 PIN_SLP(gpv0-2, INPUT, DOWN); 1220 PIN_SLP(gpv0-3, INPUT, DOWN); 1221 PIN_SLP(gpv0-4, INPUT, DOWN); 1222 PIN_SLP(gpv0-5, INPUT, DOWN); 1223 PIN_SLP(gpv0-6, INPUT, DOWN); 1224 PIN_SLP(gpv0-7, INPUT, DOWN); 1225 1226 PIN_SLP(gpv1-0, INPUT, DOWN); 1227 PIN_SLP(gpv1-1, INPUT, DOWN); 1228 PIN_SLP(gpv1-2, INPUT, DOWN); 1229 PIN_SLP(gpv1-3, INPUT, DOWN); 1230 PIN_SLP(gpv1-4, INPUT, DOWN); 1231 PIN_SLP(gpv1-5, INPUT, DOWN); 1232 PIN_SLP(gpv1-6, INPUT, DOWN); 1233 PIN_SLP(gpv1-7, INPUT, DOWN); 1234 1235 PIN_SLP(gpv2-0, INPUT, DOWN); 1236 PIN_SLP(gpv2-1, INPUT, DOWN); 1237 PIN_SLP(gpv2-2, INPUT, DOWN); 1238 PIN_SLP(gpv2-3, INPUT, DOWN); 1239 PIN_SLP(gpv2-4, INPUT, DOWN); 1240 PIN_SLP(gpv2-5, INPUT, DOWN); 1241 PIN_SLP(gpv2-6, INPUT, DOWN); 1242 PIN_SLP(gpv2-7, INPUT, DOWN); 1243 1244 PIN_SLP(gpv3-0, INPUT, DOWN); 1245 PIN_SLP(gpv3-1, INPUT, DOWN); 1246 PIN_SLP(gpv3-2, INPUT, DOWN); 1247 PIN_SLP(gpv3-3, INPUT, DOWN); 1248 PIN_SLP(gpv3-4, INPUT, DOWN); 1249 PIN_SLP(gpv3-5, INPUT, DOWN); 1250 PIN_SLP(gpv3-6, INPUT, DOWN); 1251 PIN_SLP(gpv3-7, INPUT, DOWN); 1252 1253 PIN_SLP(gpv4-0, INPUT, DOWN); 1254 }; 1255}; 1256 1257&pwm { 1258 pinctrl-0 = <&pwm0_out>; 1259 pinctrl-names = "default"; 1260 samsung,pwm-outputs = <0>; 1261 status = "okay"; 1262}; 1263 1264&rtc { 1265 status = "okay"; 1266 clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; 1267 clock-names = "rtc", "rtc_src"; 1268}; 1269 1270&sdhci_2 { 1271 bus-width = <4>; 1272 cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; 1273 cd-inverted; 1274 pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; 1275 pinctrl-names = "default"; 1276 vmmc-supply = <&ldo21_reg>; 1277 status = "okay"; 1278}; 1279 1280&sdhci_3 { 1281 #address-cells = <1>; 1282 #size-cells = <0>; 1283 non-removable; 1284 bus-width = <4>; 1285 1286 mmc-pwrseq = <&wlan_pwrseq>; 1287 pinctrl-names = "default"; 1288 pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; 1289 status = "okay"; 1290 1291 brcmf: wifi@1 { 1292 reg = <1>; 1293 compatible = "brcm,bcm4329-fmac"; 1294 interrupt-parent = <&gpx2>; 1295 interrupts = <5 IRQ_TYPE_NONE>; 1296 interrupt-names = "host-wake"; 1297 }; 1298}; 1299 1300&serial_0 { 1301 status = "okay"; 1302}; 1303 1304&serial_1 { 1305 status = "okay"; 1306}; 1307 1308&serial_2 { 1309 status = "okay"; 1310}; 1311 1312&serial_3 { 1313 status = "okay"; 1314}; 1315 1316&spi_1 { 1317 pinctrl-names = "default"; 1318 pinctrl-0 = <&spi1_bus>; 1319 cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; 1320 status = "okay"; 1321 1322 s5c73m3_spi: s5c73m3@0 { 1323 compatible = "samsung,s5c73m3"; 1324 spi-max-frequency = <50000000>; 1325 reg = <0>; 1326 controller-data { 1327 samsung,spi-feedback-delay = <2>; 1328 }; 1329 }; 1330}; 1331 1332&tmu { 1333 vtmu-supply = <&ldo10_reg>; 1334 status = "okay"; 1335}; 1336