Lines Matching +full:threshold +full:- +full:detector
5 .. See scripts/check-sysctl-docs to keep this up to date
14 ------------------------------------------------------------------------------
38 If BSD-style process accounting is enabled these values control
123 Ctrl-Alt-Delete). Writing a value to this file which doesn't
124 correspond to a running process will result in ``-ESRCH``.
126 See also `ctrl-alt-del`_.
216 ctrl-alt-del
219 When the value in this file is 0, ctrl-alt-del is trapped and
227 mode, the ctrl-alt-del is intercepted by the program before it
272 See :doc:`/driver-api/firmware/fallback-mechanisms`.
306 This value controls the hard lockup detector behavior when a hard
308 debug information. If enabled, arch-specific all-CPU stack dumping
328 See :doc:`/admin-guide/lockup-watchdogs` for more information.
349 1: Will non-maskably interrupt all CPUs and dump their backtraces when
406 -1: report an infinite number of warnings.
412 Controls whether the panic kmsg data should be reported to Hyper-V.
420 ignore-unaligned-usertrap
434 See also `unaligned-trap`_ and `unaligned-dump-stack`_. On ``ia64``,
472 The correct long-term solution is to do the permission checks at
544 By default they are equal to -1, which means generic allocation logic.
550 2) Toggle with non-default value will be set back to -1 by kernel after
552 fails, it is undefined if the value remains unmodified or is reset to -1.
567 (i.e. the hard lockup detector) on x86 systems.
570 0 Disable the hard lockup detector.
571 1 Enable the hard lockup detector.
574 The hard lockup detector monitors each CPU for its ability to respond to
576 that are programmed to generate Non-Maskable Interrupts (NMIs) periodically
584 to the guest kernel command line (see :doc:`/admin-guide/kernel-parameters`).
662 1: Will non-maskably interrupt all CPUs and dump their backtraces when
683 The only way to tune these values is to rebuild the kernel :-)
689 if your architecture did not always support 32-bit UIDs (i.e. arm,
691 applications that use the old 16-bit UID/GID system calls, if the
735 1 Panic immediately. If the `panic` sysctl is also non-zero then the
827 1-100 Attempt to throttle perf's sample rate to this
850 -1 Allow use of (almost) all events by all users.
871 '``perf record -g``' or '``perf trace --call-graph fp``'.
874 enabled, otherwise writing to this file will return ``-EBUSY``.
882 Control size of per-cpu ring buffer not counted agains mlock limit.
892 instance, when using '``perf record -g``' or '``perf trace --call-graph fp``'.
895 enabled, otherwise writing to this file will return ``-EBUSY``.
916 powersave-nap (PPC only)
919 If set, Linux-PPC will use the 'nap' mode of powersaving,
952 Value from 0 - 10000 is allowed.
988 a one-time setting until next reboot: once set, it cannot be changed by
1046 loaded to random addresses. Also for PIE-linked binaries, the
1057 non-legacy applications that would be broken this way, so for most
1066 real-root-dev
1069 See :doc:`/admin-guide/initrd`.
1072 reboot-cmd (SPARC only)
1156 See :doc:`/userspace-api/seccomp_filter`.
1159 sg-big-buff
1229 -1 Legacy per-write sysctl value handling, with no printk warnings.
1246 This value controls the soft lockup detector thread's behavior
1277 This parameter can be used to control the soft lockup detector.
1280 0 Disable the soft lockup detector.
1281 1 Enable the soft lockup detector.
1284 The soft lockup detector monitors CPUs for threads that are hogging the CPUs
1310 stop-a (SPARC only)
1313 Controls Stop-A:
1316 0 Stop-A has no effect.
1317 1 Stop-A breaks to the PROM (default).
1320 Stop-A is always enabled on a panic, so that the user can return to
1327 See :doc:`/admin-guide/sysrq`.
1333 Non-zero if the kernel has been tainted. Numeric values, which can be
1349 4096 `(O)` externally-built ("out-of-tree") module was loaded
1357 See :doc:`/admin-guide/tainted-kernels` for more information.
1364 See :doc:`/admin-guide/kernel-parameters` for more details on that particular
1367 threads-max
1377 The minimum value that can be written to ``threads-max`` is 1.
1379 The maximum value that can be written to ``threads-max`` is given by the
1382 If a value outside of this range is written to ``threads-max`` an
1409 See :doc:`/admin-guide/kernel-parameters` and
1410 :doc:`/trace/boottime-trace`.
1413 .. _unaligned-dump-stack:
1415 unaligned-dump-stack (ia64)
1426 See also `ignore-unaligned-usertrap`_.
1429 unaligned-trap
1442 See also `ignore-unaligned-usertrap`_.
1449 value is non-zero, unknown NMI is trapped and then panic occurs. At
1461 will return ``-EPERM``. Once set to 1, this can't be cleared from the
1480 This parameter can be used to disable or enable the soft lockup detector
1481 *and* the NMI watchdog (i.e. the hard lockup detector) at the same time.
1488 The soft lockup detector and the NMI watchdog can also be disabled or
1510 to re-enable cores that by default were not running the watchdog,
1517 echo 0,2-4 > /proc/sys/kernel/watchdog_cpumask
1524 events and the soft and hard lockup thresholds. The default threshold
1527 The softlockup threshold is (``2 * watchdog_thresh``). Setting this