| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra20-hsuart.txt | 33 Ex: <9600 115200 200>
34 Increase baud rate by 2% when set baud rate falls within range 9600 to 115200
50 0 to 9600 has 1% deviation
51 9600 to 115200 2% deviation
56 nvidia,adjust-baud-rates = <0 9600 100>,
57 <9600 115200 200>;
|
| /kernel/linux/linux-5.10/Documentation/networking/ |
| D | eql.rst | 282 9600 301.3
341 4 9600 900 94.7 38400 30547.4 79
342 4 9600 400 106 38400 27290.9 71
343 4 9600 600 110 38400 26298.5 68
344 3 9600 900 118 28800 24515.6 85
345 3 9600 600 120 28800 24107 83
346 3 9600 400 131 28800 22082.7 76
350 2 9600 600 176 19200 16436.6 85
351 2 9600 900 180 19200 16071.3 83
352 2 9600 400 181 19200 15982.5 83
[all …]
|
| /kernel/linux/linux-5.10/Documentation/admin-guide/ |
| D | serial-console.rst | 33 9600n8. The maximum baudrate is 115200.
39 console=ttyS1,9600 console=tty0
43 console and the 2nd serial port (ttyS1 or COM2) at 9600 baud.
74 serial = 1,9600n8 (ttyS1, 9600 bd, no parity, 8 bits)
79 append = "console=ttyS1,9600"
85 S1:23:respawn:/sbin/getty -L ttyS1 9600 vt100
|
| /kernel/linux/linux-5.10/drivers/tty/serial/ |
| D | suncore.c | 100 mode = "9600,8,n,1,-"; in sunserial_console_termios()
114 mode = "9600,8,n,1,-"; in sunserial_console_termios()
138 case 9600: cflag |= B9600; break; in sunserial_console_termios()
145 default: baud = 9600; cflag |= B9600; break; in sunserial_console_termios()
178 { 9600, B9600 },
|
| D | dz.c | 536 case 9600: in dz_encode_baud_rate()
593 baud = uart_get_baud_rate(uport, termios, old_termios, 50, 9600); in dz_set_termios()
596 baud = uart_get_baud_rate(uport, old_termios, NULL, 50, 9600); in dz_set_termios()
598 if (bflag < 0) { /* Resort to 9600. */ in dz_set_termios()
599 baud = 9600; in dz_set_termios()
865 int baud = 9600; in dz_console_setup()
|
| /kernel/linux/linux-5.10/drivers/gpu/drm/radeon/ |
| D | radeon_agp.c | 49 /* Intel E7505 Memory Controller Hub / RV350 AR [Radeon 9600XT] Needs AGPMode 4 (deb #515326) */
59 /* Intel 82855PM host bridge / Mobility 9600 M10 RV350 Needs AGPMode 1 (lp #195051) */
86 /* Intel 82852/82855 host bridge / Mobility 9600 M10 RV350 Needs AGPMode 1 (deb #467460) */
89 /* Intel 82852/82855 host bridge / Mobility 9600 M10 RV350 Needs AGPMode 1 (lp #203007) */
92 /* Intel 82852/82855 host bridge / Mobility 9600 M10 RV350 Needs AGPMode 1 (lp #141551) */
95 /* Intel 82852/82855 host bridge / Mobility 9600/9700 Needs AGPMode 1 (deb #510208) */
|
| /kernel/linux/linux-5.10/arch/arc/boot/dts/ |
| D | abilis_tb101_dvk.dts | 17 bootargs = "earlycon=uart8250,mmio32,0xff100000,9600n8 console=ttyS0,9600n8";
|
| D | abilis_tb100_dvk.dts | 17 bootargs = "earlycon=uart8250,mmio32,0xff100000,9600n8 console=ttyS0,9600n8";
|
| /kernel/linux/linux-5.10/drivers/usb/serial/ |
| D | upd78f0730.c | 17 * - baud rates: 0, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 153600
289 0, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 153600 in upd78f0730_get_baud_rate()
299 tty_encode_baud_rate(tty, 9600, 9600); in upd78f0730_get_baud_rate()
|
| D | mct_u232.c | 137 case 9600: in mct_u232_calculate_baud_rate()
148 *result = 9600; in mct_u232_calculate_baud_rate()
161 case 9600: break; in mct_u232_calculate_baud_rate()
167 value = 9600; in mct_u232_calculate_baud_rate()
168 *result = 9600; in mct_u232_calculate_baud_rate()
|
| D | ir-usb.c | 215 (rates & USB_IRDA_BR_9600) ? " 9600" : "", in ir_startup()
400 case 9600: in ir_set_termios()
426 baud = 9600; in ir_set_termios()
|
| /kernel/linux/linux-5.10/arch/powerpc/platforms/embedded6xx/ |
| D | ls_uart.c | 56 #define AVR_QUOT(clock) ((clock) + 8 * 9600) / (16 * 9600)
|
| /kernel/linux/linux-5.10/drivers/acpi/ |
| D | acpi_pnp.c | 227 {"PNPC001"}, /* Compaq 2400/9600 Modem */
230 {"PNPC100"}, /* Standard 9600 bps Modem */
234 {"PNPC104"}, /* Standard 9600 bps Modem */
238 {"PNPC108"}, /* Standard 9600 bps Modem */
242 {"PNPC10C"}, /* Standard 9600 bps Modem */
|
| /kernel/linux/linux-5.10/drivers/tty/serial/8250/ |
| D | 8250_pnp.c | 210 /* Compaq 2400/9600 Modem */
216 /* Standard 9600 bps Modem */
224 /* Standard 9600 bps Modem*/
232 /* Standard 9600 bps Modem */
240 /* Standard 9600 bps Modem */
|
| D | 8250_early.c | 17 * earlycon=uart8250,io,0x3f8,9600n8
21 * console=uart8250,io,0x3f8,9600n8
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/power/reset/ |
| D | qnap-poweroff.txt | 9 9600, and a different character, '1'.
|
| /kernel/linux/linux-5.10/arch/powerpc/platforms/powermac/ |
| D | Kconfig | 31 including the 7500, 8500, 9500, 9600. Support exists for
|
| /kernel/linux/linux-5.10/arch/arm/configs/ |
| D | shannon_defconfig | 11 CONFIG_CMDLINE="console=ttySA0,9600 console=tty1 root=/dev/mtdblock2 init=/linuxrc"
|
| D | pleb_defconfig | 13 CONFIG_CMDLINE="console=ttySA0,9600 mem=16M@0xc0000000 mem=16M@0xc8000000 root=/dev/ram initrd=0xc0…
|
| D | lart_defconfig | 11 CONFIG_CMDLINE="console=ttySA0,9600 root=/dev/ram"
|
| /kernel/linux/linux-5.10/arch/powerpc/boot/dts/ |
| D | mvme5100.dts | 60 current-speed = <9600>;
71 current-speed = <9600>;
|
| /kernel/linux/linux-5.10/arch/m68k/atari/ |
| D | debug.c | 175 baud = B9600; /* use default 9600bps for non-implemented rates */ in atari_init_mfp_port()
224 baud = B9600; /* use default 9600bps for non-implemented rates */ in atari_init_scc_port()
271 /* 4800 selects 7812.5, 115200 selects 500000, all other (incl. 9600 as in atari_init_midi_port()
|
| /kernel/linux/linux-5.10/arch/powerpc/kernel/ |
| D | udbg_16550.c | 105 speed = 9600; in udbg_uart_setup()
153 speed = 9600; in udbg_probe_uart_speed()
|
| /kernel/linux/linux-5.10/Documentation/networking/device_drivers/ethernet/neterion/ |
| D | s2io.rst | 55 a. Jumbo frames. Xframe I/II supports MTU up to 9600 bytes,
119 a. Set MTU to maximum(9000 for switch setup, 9600 in back-to-back configuration)
|
| /kernel/linux/linux-5.10/Documentation/hwmon/ |
| D | coretemp.rst | 136 T9900/9800/9600/9550/9500/9400/9300/8300/8100 105
142 P9700/9600/9500/8800/8700/8600/8400/7570 105
|