Lines Matching refs:console
14 the console before standard serial driver is probed. The console is
33 bool "Support for console on AMBA serial port"
38 console (the system console is the device which receives all kernel
41 Even if you say Y here, the currently visible framebuffer console
42 (/dev/tty0) will still be used as the system console by default, but
44 "console=ttyAM0". (Try "man bootparam" or see the documentation of
60 bool "Support for console on AMBA serial port"
66 console (the system console is the device which receives all kernel
69 Even if you say Y here, the currently visible framebuffer console
70 (/dev/tty0) will still be used as the system console by default, but
72 "console=ttyAMA0". (Try "man bootparam" or see the documentation of
77 bool "Early console using ARM semihosting"
83 Support for early debug console using ARM semihosting. This enables
84 the console before standard serial driver is probed. This is enabled
85 with "earlycon=smh" on the kernel command line. The console is
89 bool "Early console using RISC-V SBI"
95 Support for early debug console using RISC-V SBI. This enables
96 the console before standard serial driver is probed. This is enabled
97 with "earlycon=sbi" on the kernel command line. The console is
116 bool "Support for console on a BCM1xxx DUART serial port"
122 system console (the system console is the device which receives all
139 bool "Support for console on AT91 serial port"
144 AT91 processor as the system console (the system
145 console is the device which receives all kernel messages and
176 /dev/, and pass "console=ttyATn" to the kernel.
181 bool "Serial console over KGDB NMI debugger port"
185 as a normal console (assuming that the port is attached to KGDB).
189 This is because this console driver processes the input in NMI
192 Note that since the console interprets input and uses polling
195 use raw console.
208 bool "Support for console on meson"
214 system console (the system console is the device which
228 bool "Support for console on CLPS711X serial port"
232 Even if you say Y here, the currently visible virtual console
233 (/dev/tty0) will still be used as the system console by default, but
235 "console=ttyCL1".
264 bool "Support for console on Samsung SoC serial port"
270 an virtual console.
272 Even if you say Y here, the currently visible virtual console
273 (/dev/tty0) will still be used as the system console by default, but
275 "console=ttySACx". (Try "man bootparam" or see the documentation of
290 bool "Support for console on SiRF SoC serial port"
294 Even if you say Y here, the currently visible virtual console
295 (/dev/tty0) will still be used as the system console by default, but
297 "console=ttySiRFx". (Try "man bootparam" or see the documentation of
322 bool "Support for console on a Tegra TCU serial port"
328 system console (the system console is the device which receives all
364 bool "Support console on DECstation DZ serial driver"
370 system console (the system console is the device which receives all
374 Note that the firmware uses ttyS3 as the serial console on
394 bool "Support for console on a DECstation Z85C30 serial port"
400 system console (the system console is the device which receives all
404 Note that the firmware uses ttyS1 as the serial console on the
424 make it the console by answering Y to this option.
426 Even if you say Y here, the currently visible virtual console
427 (/dev/tty0) will still be used as the system console by default, but
429 "console=ttyFB". (Try "man bootparam" or see the documentation of
457 CPU you can make it the console by answering Y to this option.
459 Even if you say Y here, the currently visible virtual console
460 (/dev/tty0) will still be used as the system console by default, but
462 "console=ttySA0". (Try "man bootparam" or see the documentation of
486 CPU you can make it the console by answering Y to this option.
488 Even if you say Y here, the currently visible virtual console
489 (/dev/tty0) will still be used as the system console by default, but
491 "console=ttySA0". (Try "man bootparam" or see the documentation of
511 CPU you can make it the console by answering Y/M to this option.
513 Even if you say Y/M here, the currently visible virtual console
514 (/dev/tty0) will still be used as the system console by default, but
516 "console=ttymxc0". (Try "man bootparam" or see the documentation of
541 bool "Support for console on Xilinx uartlite serial port"
547 console (the system console is the device which receives all kernel
578 on your Sparc system as the console, you can do so by answering
594 on your Sparc system as the console, you can do so by answering
607 software console. The following steps need to be completed to use
613 root on this console.)
614 4. Change the kernel command console parameter to: console=ttyB0
617 bool "Support for console on serial MUX"
623 bool "PDC software console support"
626 Saying Y here will enable the software based PDC console to be
627 used as the system console. This is useful for machines in
628 which the hardware based console has not been written yet. The
629 following steps must be completed to use the PDC console:
634 root on this console.)
635 4. Change the kernel command console parameter to: console=ttyB0
650 on your Sparc system as the console, you can do so by answering
657 This driver supports the console device found on SUN4V Sparc
690 bool "Support for console on SuperH SCI(F)" if EXPERT
696 bool "Support for early console on SuperH SCI(F)" if EXPERT
716 bool "Enable PNX8XX0 serial console"
721 to use serial console, say Y. Otherwise, say N.
735 bool "Enable LPC32XX high speed UART serial console"
740 ports on the LPC32XX as the console, you can do so by answering
769 bool "Coldfire serial console support"
773 Enable a ColdFire internal serial port to be the system console.
815 on your (Power)Mac as the console, you can do so by answering
827 bool "Support for console on CPM SCC/SMC serial port"
832 console (the system console is the device which receives all kernel
835 Even if you say Y here, the currently visible framebuffer console
836 (/dev/tty0) will still be used as the system console by default, but
838 "console=ttyCPM0". (Try "man bootparam" or see the documentation of
850 to use a serial port as a console, this must be included in kernel and
854 bool "PIC32 serial console support"
858 If you have a PIC32, this driver supports the putting a console on one
861 Say Y to use the PIC32 console, otherwise say N.
870 for use as console, it must be included in kernel and not as a
879 of the Freescale MPC52xx family as a console.
886 Select the MPC52xx console baud rate.
888 console baudrate
936 bool "Enable NEC VR4100 series Serial Interface Unit console"
941 a console on a serial port, say Y. Otherwise, say N.
965 bool "MSM serial console support"
982 Serial console driver for Qualcomm Technologies Inc's GENI based
991 bool "VIA VT8500 serial console support"
1013 console.
1015 Even if you say Y here, the currently visible virtual console
1016 (/dev/tty0) will still be used as the system console by default, but
1018 "console=ttyOx". (Try "man bootparam" or see the documentation of
1038 system console.
1040 Even if you say Y here, the currently visible virtual console
1041 (/dev/tty0) will still be used as the system console by default, but
1043 "console=ttySIFx". (Try "man bootparam" or see the documentation of
1063 system console.
1087 Support for console on SCCNXP serial ports.
1144 BCM7xxx (STB) - DOCSIS console
1153 you can make it the console by answering Y to this option.
1167 Support for running a console on the GRLIB APBUART
1176 bool "Altera JTAG UART console support"
1181 Enable a Altera JTAG UART port to be the system console.
1188 Bypass console output and keep going even if there is no
1216 bool "Altera UART console support"
1221 Enable a Altera UART port to be the system console.
1247 bool "Support for console on Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
1251 Say Y here if you wish to use the PCH UART as the system console
1252 (the system console is the device which receives all kernel messages and
1265 bool "MXS AUART console support"
1269 Enable a MXS AUART port to be the system console.
1280 bool "Cadence UART console support"
1285 Enable a Cadence UART port to be the system console.
1304 Enable a built-in UART port of the AR933X to be the system console.
1323 bool "MPS2 UART console support"
1336 bool "EFM32 UART/USART console support"
1402 you can make it the console by answering Y to this option.
1418 SoCs, you can make it the console by answering Y to this option.
1433 SoCs, you can make it the console by answering Y to this option.
1448 bool "Support for console on ST ASC"
1471 bool "Spreadtrum UART console support"
1476 Support for early debug console using Spreadtrum's serial. This enables
1477 the console before standard serial driver is probed. This is enabled
1478 with "earlycon" on the kernel command line. The console is
1495 bool "Support for console on STM32"
1517 Say 'Y' here if you wish to use Armada-3700 UART as the system console.
1518 (the system console is the device which receives all kernel messages
1539 as the system console.
1558 console. Only earlycon is implemented currently.
1575 bool "Support for console on MILBEAUT USIO/UART serial port"
1582 SoCs as the system console (the system console is the device which