Home
last modified time | relevance | path

Searched full:sw3 (Results 1 – 25 of 74) sorted by relevance

123

/kernel/linux/linux-5.10/Documentation/devicetree/bindings/regulator/
Dltc3676.txt8 - regulators: Contains eight regulator child nodes sw1, sw2, sw3, sw4,
13 nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify
20 Regulators sw1, sw2, sw3, sw4 can regulate the feedback reference from:
54 sw3_reg: sw3 {
Dltc3589.txt8 - regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out,
13 nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify
20 Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from
54 sw3_reg: sw3 {
Dpv88060.txt11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
97 SW3 {
98 regulator-name = "sw3";
Dpfuze100.yaml19 sw1a,sw1b,sw2,sw3,swbst,vsnvs,vrefddr,vldo1,vldo2,vccsd,v33,vldo3,vldo4
21 sw1,sw2,sw3,vsnvs,vldo1,vldo2,vccsd,v33,vldo3,vldo4
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/mfd/
Dmc13xxx.txt59 sw3 : regulator SW3 (register 29, bit 20)
88 sw3 : regulator SW3 (register 26, bit 0)
/kernel/linux/linux-5.10/arch/arm/boot/dts/
Dimx28-eukrea-mbmx28lc.dtsi22 button-sw3 {
27 sw3 {
28 label = "SW3";
192 gpio_button_sw3_pins_mbmx28lc: gpio-button-sw3-mbmx28lc@0 {
Dimx53-qsrb.dts58 sw3_reg: sw3 {
59 regulator-name = "SW3";
Dat91-kizbox3-hs.dts85 SW3 {
86 label = "SW3";
Darmada-388-clearfog-base.dts23 /* The rear SW3 button */
Dpm9g45.dts180 label = "SW3";
Darmada-388-clearfog.dts39 /* The rear SW3 button */
Dimx7-tqma7.dtsi59 sw3a_reg: sw3 {
Dqcom-ipq8064-rb3011.dts78 label = "sw3";
Dimx53-usbarmory.dts168 sw3_reg: sw3 {
/kernel/linux/linux-5.10/Documentation/hid/
Dhid-alps.rst114 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
164 Byte1 1 1 1 0 1 SW3 SW2 SW1
173 SW1-SW3:
/kernel/linux/linux-5.10/drivers/media/dvb-frontends/
Ddib0090.h87 extern int dib0090_set_switch(struct dvb_frontend *fe, u8 sw1, u8 sw2, u8 sw3);
157 u8 sw1, u8 sw2, u8 sw3) in dib0090_set_switch() argument
/kernel/linux/linux-5.10/drivers/regulator/
Dltc3676.c172 /* SW1, SW2, SW3, SW4 linear 0.8V-3.3V with scalar via R1/R2 feeback res */
227 LTC3676_LINEAR_REG(SW3, sw3, BUCK3, DVB3A),
Dltc3589.c144 /* SW1, SW2, SW3, LDO2 */
255 LTC3589_LINEAR_REG(SW3, sw3, B3DTV1),
Dpcap-regulator.c133 /* SW3 STBY is on PCAP_REG_AUXVREG */
134 VREG_INFO(SW3, PCAP_REG_SWCTRL, 11, 12, 24, NA),
Dpfuze100-regulator.c418 PFUZE3000_SW3_REG(PFUZE3000, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
433 PFUZE3000_SW3_REG(PFUZE3001, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
489 { .name = "sw3", },
506 { .name = "sw3", },
Dmc13783-regulator.c253 MC13783_DEFINE_SW(SW3, sw3, SWITCHERS5, SWITCHERS5, mc13783_sw3_val),
/kernel/linux/linux-5.10/arch/sh/boards/mach-rsk/
Ddevices-rsk7203.c101 .desc = "SW3",
/kernel/linux/linux-5.10/arch/mips/boot/dts/pic32/
Dpic32mzda_sk.dts70 button@sw3 {
/kernel/linux/linux-5.10/Documentation/networking/
Darcnet-hardware.rst832 SW3 1-8: Node ID Select
848 The eight switches in group SW3 are used to set the node ID. Each node
1998 SW3 1-5: IRQ Select
2008 The eight switches in SW3 are used to set the node ID. Each node attached
2072 *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON.
2080 Switches 1-5 of the switch block SW3 control the IRQ level::
2095 The switches 6-7 of the switch block SW3 are used to determine the timeout
2851 | SW3 | || | |
2870 SW3 1-5: IRQ Select
2876 Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not
[all …]
/kernel/linux/linux-5.10/arch/arm64/boot/dts/rockchip/
Drk3326-odroid-go2.dts38 * | sw3 sw4 | | sw7 sw5 |
56 sw3 {

123