Searched refs:CRT (Results 1 – 15 of 15) sorted by relevance
| /kernel/linux/linux-5.10/Documentation/fb/ |
| D | viafb.rst | 16 Device: CRT, LCD, DVI
20 CRT:
42 viafb_active_dev=CRT+DVI viafb_dvi_port=DVP1
109 This option is used to specify active devices.(CRT, DVI, CRT+LCD...)
121 To enable two devices, such as CRT+DVI::
123 modprobe viafb viafb_active_dev=CRT+DVI;
127 modprobe viafb viafb_active_dev=CRT+DVI
131 modprobe viafb viafb_active_dev=DVI+CRT...
135 If CRT is primary and DVI is secondary, we should use::
137 modprobe viafb viafb_active_dev=CRT+DVI viafb_SAMM_ON=1...
[all …]
|
| D | modedb.rst | 94 The GTF is limited by the fact that it is designed mainly for CRT displays.
100 The CVT addresses these limitations. If used with CRT's, the formula used
107 new CRT displays and probably with most flatpanels, if 'reduced blanking'
|
| /kernel/linux/linux-5.10/Documentation/ABI/testing/ |
| D | sysfs-platform-eeepc-laptop | 9 - 2 = CRT
10 - 3 = LCD+CRT
|
| D | sysfs-platform-asus-laptop | 11 ||`-- CRT
17 - 3 (0011b) CRT+LCD.
|
| /kernel/linux/linux-5.10/drivers/gpu/drm/nouveau/nvkm/engine/disp/ |
| D | dacgf119.c | 41 case 0: state->proto = CRT; break; in gf119_dac_state()
|
| D | dacnv50.c | 92 case 0: state->proto = CRT; break; in nv50_dac_state()
|
| D | ior.h | 26 CRT, enumerator
|
| D | outp.c | 65 case DCB_OUTPUT_ANALOG: *type = DAC; return CRT; in nvkm_outp_xlat()
|
| /kernel/linux/linux-5.10/arch/sh/cchips/ |
| D | Kconfig | 17 CRT color controller, IrDA up to 4 Mbps, and a
|
| /kernel/linux/linux-5.10/Documentation/admin-guide/laptops/ |
| D | asus-laptop.rst | 123 | Bin | Val | DVI | TV | CRT | LCD |
|
| D | thinkpad-acpi.rst | 655 LCD, CRT or DVI (if available). The following commands are available::
|
| /kernel/linux/linux-5.10/drivers/video/fbdev/ |
| D | cirrusfb.c | 348 CRT, enumerator
2829 case CRT: in cirrusfb_dbg_print_regs()
2863 cirrusfb_dbg_print_regs(info, regbase, CRT, in cirrusfb_dbg_reg_dump()
|
| D | Kconfig | 1916 Frame buffer driver for the CRT and LCD controllers in the Silicon
|
| /kernel/linux/linux-5.10/drivers/pinctrl/tegra/ |
| D | pinctrl-tegra20.c | 2056 MUX_PG(crtp, CRT, RSVD2, RSVD3, RSVD4, 0x20, 14, 0x98, 20, 0xa4, 24),
2113 MUX_PG(lm1, DISPLAYA, DISPLAYB, RSVD3, CRT, 0x1c, 25, 0x90, 28, -1, -1),
|
| D | pinctrl-tegra30.c | 2348 …PINGROUP(crt_hsync_pv6, CRT, RSVD2, RSVD3, RSVD4, 0x311c, N, …
2349 …PINGROUP(crt_vsync_pv7, CRT, RSVD2, RSVD3, RSVD4, 0x3120, N, …
|