| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/gpio/ |
| D | gpio-axp209.txt | 46 pins = "GPIO0";
59 Each GPIO is independent from the other (i.e. GPIO0 in gpio_in function does
66 GPIO0 | gpio_in, gpio_out, ldo, adc
74 GPIO0 | gpio_in, gpio_out, ldo, adc
|
| D | ibm,ppc4xx-gpio.txt | 19 GPIO0: gpio@ef600b00 {
|
| /kernel/linux/linux-5.10/drivers/net/wireless/realtek/rtl818x/rtl8187/ |
| D | rfkill.c | 24 gpio = rtl818x_ioread8(priv, &priv->map->GPIO0); in rtl8187_is_radio_enabled()
25 rtl818x_iowrite8(priv, &priv->map->GPIO0, gpio & ~priv->rfkill_mask); in rtl8187_is_radio_enabled()
|
| D | leds.c | 42 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0x01); in led_turn_on()
80 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0x01); in led_turn_off()
|
| /kernel/linux/linux-5.10/drivers/pinctrl/ |
| D | pinctrl-xway.c | 116 MFP_XWAY(GPIO0, GPIO, EXIN, NONE, TDM),
203 static const unsigned xway_exin_pin_map[] = {GPIO0, GPIO1, GPIO2, GPIO39, GPIO46, GPIO9};
205 static const unsigned pins_exin0[] = {GPIO0};
352 MFP_XWAY(GPIO0, GPIO, EXIN, MII, TDM),
386 static const unsigned ase_exin_pin_map[] = {GPIO6, GPIO29, GPIO0};
390 static const unsigned ase_pins_exin2[] = {GPIO0};
480 MFP_XWAY(GPIO0, GPIO, EXIN, SDIO, TDM),
514 static const unsigned danube_exin_pin_map[] = {GPIO0, GPIO1, GPIO2};
516 static const unsigned danube_pins_exin0[] = {GPIO0};
655 MFP_XWAY(GPIO0, GPIO, EXIN, SDIO, TDM),
[all …]
|
| D | pinctrl-lantiq.h | 106 GPIO0 = 0, enumerator
|
| /kernel/linux/linux-5.10/drivers/media/usb/dvb-usb/ |
| D | dib07x0.h | 6 GPIO0 = 0, enumerator
|
| D | dib0700_devices.c | 95 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in bristol_frontend_attach()
97 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 0); in bristol_frontend_attach()
323 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk7700d_frontend_attach()
475 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk7700ph_frontend_attach()
721 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk7700p_frontend_attach()
1008 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk7070p_frontend_attach()
1066 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk7770p_frontend_attach()
1363 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk807x_frontend_attach()
1397 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk807xpvr_frontend_attach0()
1770 dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1); in stk809x_frontend_attach()
[all …]
|
| /kernel/linux/linux-5.10/arch/sh/kernel/cpu/sh4a/ |
| D | setup-shx3.c | 185 GPIO0, GPIO1, GPIO2, GPIO3, enumerator
232 INTC_VECT(GPIO0, 0xe40), INTC_VECT(GPIO1, 0xe60),
267 DU, GPIO3, GPIO2, GPIO1, GPIO0, PAM, 0, 0,
303 GPIO2, GPIO1, GPIO0, IRM } },
|
| D | setup-sh7786.c | 496 GPIO0, GPIO1, enumerator
541 INTC_VECT(GPIO0, 0xea0), INTC_VECT(GPIO1, 0xec0),
611 HSPI, GPIO0, GPIO1, Thermal,
650 { 0xfe410858, 0, 32, 8, /* INT2PRI22 */ { HSPI, GPIO0,
|
| /kernel/linux/linux-5.10/arch/mips/boot/dts/ralink/ |
| D | gardena_smart_gateway_mt7688.dts | 45 * <&pinmux_i2s_gpio> (covers GPIO0..3) is needed here as
178 pinctrl-0 = <&pinmux_i2s_gpio>; /* GPIO0..3 */
|
| /kernel/linux/linux-5.10/arch/arm/mach-pxa/ |
| D | pxa320.c | 25 MFP_ADDR_X(GPIO0, GPIO4, 0x0124),
|
| D | pxa300.c | 25 MFP_ADDR_X(GPIO0, GPIO2, 0x00b4),
|
| D | mfp-pxa2xx.h | 61 #define GPIO0_GPIO MFP_CFG_IN(GPIO0, AF0)
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | ste,nomadik.txt | 114 pins = "GPIO0", "GPIO2";
125 pins = "GPIO0", "GPIO2";
|
| D | nuvoton,npcm7xx-pinctrl.txt | 44 "GPIO0/IOX1DI", "GPIO1/IOX1LD", "GPIO2/IOX1CK", "GPIO3/IOX1D0",
126 pins = "GPIO0/IOX1DI";
197 pins = "GPIO0/IOX1DI";
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | bcm2837-rpi-cm3-io3.dts | 20 gpio-line-names = "GPIO0",
|
| D | bcm2835-rpi-cm1-io1.dts | 20 gpio-line-names = "GPIO0",
|
| D | sun5i-a13-q8-tablet.dts | 54 enable-gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; /* AXP GPIO0 */
|
| /kernel/linux/linux-5.10/arch/arm64/boot/dts/allwinner/ |
| D | sun50i-a64-oceanic-5205-5inmfd.dts | 44 AVDD28-supply = <®_ldo_io0>; /* VDD_CTP: GPIO0-LDO */
|
| D | axp803.dtsi | 30 pins = "GPIO0";
|
| /kernel/linux/linux-5.10/arch/arm/mach-mmp/ |
| D | pxa168.c | 36 MFP_ADDR_X(GPIO0, GPIO36, 0x04c),
|
| D | pxa910.c | 34 MFP_ADDR_X(GPIO0, GPIO54, 0xdc),
|
| D | mmp2.c | 36 MFP_ADDR_X(GPIO0, GPIO58, 0x54),
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/interrupt-controller/ |
| D | brcm,bcm2835-armctrl-ic.txt | 96 17: GPIO0
|