Searched refs:SW2 (Results 1 – 25 of 26) sorted by relevance
12
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | r8a7792-blanche.dts | 117 label = "SW2-1";
124 label = "SW2-2";
131 label = "SW2-3";
138 label = "SW2-4";
|
| D | sh73a0-kzm9g.dts | 113 label = "SW2-R";
119 label = "SW2-L";
125 label = "SW2-P";
131 label = "SW2-U";
137 label = "SW2-D";
|
| D | at91-kizbox3-hs.dts | 78 SW2 {
79 label = "SW2";
|
| D | r8a7793-gose.dts | 73 label = "SW2-1";
80 label = "SW2-2";
87 label = "SW2-3";
94 label = "SW2-4";
|
| D | r8a7791-koelsch.dts | 87 label = "SW2-1";
94 label = "SW2-2";
101 label = "SW2-3";
108 label = "SW2-4";
|
| D | r8a7790-lager.dts | 86 label = "SW2-1";
93 label = "SW2-2";
100 label = "SW2-3";
107 label = "SW2-4";
|
| D | imx53-qsrb.dts | 51 regulator-name = "SW2";
|
| D | r7s72100-rskrza1.dts | 50 label = "SW2";
|
| D | r8a7792-wheat.dts | 62 label = "SW2";
|
| D | r8a7742-iwg21d-q7.dts | 219 /* SW2[6] determines which connector is activated
|
| D | exynos5422-odroidxu3-common.dtsi | 23 * The power button (SW2) is connected to the PWRON
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/regulator/ |
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
90 SW2 {
|
| /kernel/linux/linux-5.10/drivers/regulator/ |
| D | pcap-regulator.c | 132 VREG_INFO(SW2, PCAP_REG_SWCTRL, 6, 7, NA, NA),
228 VREG(VAUX4), VREG(VSIM), VREG(VSIM2), VREG(VVIB), VREG(SW1), VREG(SW2),
|
| D | pfuze100-regulator.c | 381 PFUZE100_SW_REG(PFUZE100, SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000),
399 PFUZE100_SW_REG(PFUZE200, SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000),
417 PFUZE3000_SW_REG(PFUZE3000, SW2, PFUZE100_SW2VOL, 0x7, pfuze3000_sw2lo),
432 PFUZE3000_SW_REG(PFUZE3001, SW2, PFUZE100_SW2VOL, 0x7, pfuze3000_sw2lo),
|
| D | cpcap-regulator.c | 341 CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2,
417 CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2,
|
| D | pv88060-regulator.c | 218 PV88060_SW(PV88060, SW2, 5000000),
|
| D | ltc3676.c | 226 LTC3676_LINEAR_REG(SW2, sw2, BUCK2, DVB2A),
|
| D | ltc3589.c | 254 LTC3589_LINEAR_REG(SW2, sw2, B2DTV1),
|
| D | mc13892-regulator.c | 268 MC13892_SW_DEFINE(SW2, sw2, SWITCHERS1, SWITCHERS1, mc13892_sw),
|
| /kernel/linux/linux-5.10/Documentation/hid/ |
| D | hid-alps.rst | 114 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
164 Byte1 1 1 1 0 1 SW3 SW2 SW1
|
| /kernel/linux/linux-5.10/Documentation/networking/ |
| D | arcnet-hardware.rst | 803 < | SW1 | | SW2 | |
831 SW2 1-6: Reserved for Future Use
1051 | | | SW2 |
1064 SW2: DIP-Switches for Memory Base and I/O Base addresses
1087 The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
1104 DIP Switches 1-5 of SW2 encode the RAM and ROM Address Range:
1377 The eight switches in SW2 are used to set the node ID. Each node attached
1575 SW2 1-8: Node ID Select (ID0-ID7)
1588 The eight switches in SW2 are used to set the node ID. Each node attached
1833 | |SW2| |
[all …]
|
| /kernel/linux/linux-5.10/include/linux/mfd/ |
| D | ezx-pcap.h | 131 #define SW2 18 macro
|
| /kernel/linux/linux-5.10/arch/powerpc/boot/dts/ |
| D | sbc8548-altflash.dts | 6 * Requires switching JP12 jumpers and changing SW2.8 setting.
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/mfd/ |
| D | mc13xxx.txt | 87 sw2 : regulator SW2 (register 25, bit 0)
|
| /kernel/linux/linux-5.10/Documentation/networking/device_drivers/appletalk/ |
| D | ltpc.rst | 84 SW2 IRQ 3
|
12