Searched refs:INIT_ZONE (Results 1 – 8 of 8) sorted by relevance
| /kernel/linux/linux-5.10/drivers/net/wireless/rsi/ |
| D | rsi_91x_sdio_ops.c | 39 rsi_dbg(INIT_ZONE, in rsi_sdio_master_access_msword()
55 rsi_dbg(INIT_ZONE, "%s:MASTER_ACCESS_LSBYTE:0x%x\n", __func__, byte); in rsi_sdio_master_access_msword()
171 rsi_dbg(INIT_ZONE, "%s: Enabling SDIO High speed\n", __func__); in rsi_init_sdio_slave_regs()
187 rsi_dbg(INIT_ZONE, "%s: Initializing SDIO read start level\n", __func__); in rsi_init_sdio_slave_regs()
200 rsi_dbg(INIT_ZONE, "%s: Initializing FIFO ctrl registers\n", __func__); in rsi_init_sdio_slave_regs()
|
| D | rsi_91x_usb.c | 663 rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__); in rsi_init_usb_interface()
791 rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__); in rsi_probe()
811 rsi_dbg(INIT_ZONE, "%s: 9113 module detected\n", __func__); in rsi_probe()
814 rsi_dbg(INIT_ZONE, "%s: 9116 module detected\n", __func__); in rsi_probe()
832 rsi_dbg(INIT_ZONE, "Loading firmware...\n"); in rsi_probe()
839 rsi_dbg(INIT_ZONE, "%s: Device Init Done\n", __func__); in rsi_probe()
|
| D | rsi_91x_sdio.c | 364 rsi_dbg(INIT_ZONE, "%s: Setting the block length\n", __func__); in rsi_setblocklength()
856 rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__); in rsi_init_sdio_interface()
869 rsi_dbg(INIT_ZONE, "%s: Setup card successfully\n", __func__); in rsi_init_sdio_interface()
934 rsi_dbg(INIT_ZONE, "%s: Bring TA out of reset\n", __func__); in rsi_sdio_ta_reset()
981 rsi_dbg(INIT_ZONE, "***** TA Reset done *****\n"); in rsi_sdio_ta_reset()
1017 rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__); in rsi_probe()
1065 rsi_dbg(INIT_ZONE, "%s: Registered Interrupt handler\n", __func__); in rsi_probe()
1550 rsi_dbg(INIT_ZONE, "%s: Registering driver\n", __func__); in rsi_module_init()
|
| D | rsi_91x_main.c | 438 rsi_dbg(INIT_ZONE, "%s: Module init called\n", __func__); in rsi_91x_hal_module_init()
452 rsi_dbg(INIT_ZONE, "%s: Module exit called\n", __func__); in rsi_91x_hal_module_exit()
|
| D | rsi_91x_hal.c | 713 rsi_dbg(INIT_ZONE, "Flash capacity: %d KiloBytes\n", flash_sz); in read_flash_capacity()
915 rsi_dbg(INIT_ZONE, "%s: Loading file %s\n", __func__, metadata_p->name); in rsi_load_9113_firmware()
1019 rsi_dbg(INIT_ZONE, "***** Load 9116 TA Instructions *****\n"); in rsi_load_9116_firmware()
1038 rsi_dbg(INIT_ZONE, "%s: loading file %s\n", __func__, metadata_p->name); in rsi_load_9116_firmware()
1113 rsi_dbg(INIT_ZONE, "%s: Successfully loaded %s instructions\n", in rsi_load_9116_firmware()
|
| D | rsi_91x_mgmt.c | 2010 rsi_dbg(INIT_ZONE, "Dual band supported\n"); in rsi_handle_ta_confirm_type()
2014 rsi_dbg(INIT_ZONE, in rsi_handle_ta_confirm_type()
2134 rsi_dbg(INIT_ZONE, "Card ready indication from Common HAL\n"); in rsi_handle_card_ready()
2141 rsi_dbg(INIT_ZONE, "Card ready indication from WLAN HAL\n"); in rsi_handle_card_ready()
2152 rsi_dbg(INIT_ZONE, "MAC Addr %pM", common->mac_addr); in rsi_handle_card_ready()
|
| D | rsi_main.h | 38 #define INIT_ZONE BIT(2) /* For Driver Init Seq Msgs */ macro
|
| D | rsi_91x_mac80211.c | 1985 rsi_dbg(INIT_ZONE, "%s: Performing mac80211 attach\n", __func__); in rsi_mac80211_attach()
|