Lines Matching +full:- +full:pins
1 // SPDX-License-Identifier: GPL-2.0-or-later
6 #include "ste-ab8500.dtsi"
12 ab8500-gpiocontroller {
14 pinctrl-names = "default";
15 pinctrl-0 = <&gpio2_default_mode>,
40 * Pins 2, 4, 10, 11, 12, 13, 16, 24, 25, 36, 37, 38, 39 and 42
50 pins = "GPIO2_T9";
51 input-enable;
52 bias-pull-down;
63 pins = "GPIO4_W2";
64 input-enable;
65 bias-pull-down;
76 pins = "GPIO10_U17";
77 input-enable;
78 bias-pull-down;
89 pins = "GPIO11_AA18";
90 input-enable;
91 bias-pull-down;
102 pins = "GPIO12_U16";
103 input-enable;
104 bias-pull-down;
115 pins = "GPIO13_W17";
116 input-enable;
117 bias-pull-down;
128 pins = "GPIO16_F15";
129 input-enable;
130 bias-pull-down;
141 pins = "GPIO24_T14";
142 input-enable;
143 bias-pull-down;
154 pins = "GPIO25_R16";
155 input-enable;
156 bias-pull-down;
167 pins = "GPIO36_A17";
168 input-enable;
169 bias-pull-down;
180 pins = "GPIO37_E15";
181 input-enable;
182 bias-pull-down;
193 pins = "GPIO38_C17";
194 input-enable;
195 bias-pull-down;
206 pins = "GPIO39_E16";
207 input-enable;
208 bias-pull-down;
219 pins = "GPIO42_U2";
220 input-enable;
221 bias-pull-down;
226 * Pins 26 and 35 muxed in as GPIO, and configured as OUTPUT LOW
235 pins = "GPIO26_M16";
236 output-low;
247 pins = "GPIO35_W15";
248 output-low;
253 * This sets up the YCBCR connector pins, i.e. analog video out.
263 pins = "GPIO6_Y18",
267 input-enable;
268 bias-disable;
272 /* This sets up the PWM pins 14 and 15 */
280 pins = "GPIO14_F14",
282 input-enable;
283 bias-pull-down;
295 pins = "GPIO17_P5",
299 input-enable;
300 bias-pull-down;
304 /* This sets up the USB UICC pins */
312 pins = "GPIO21_H19",
315 input-enable;
316 bias-pull-down;
320 /* This sets up the microphone pins */
330 pins = "GPIO27_J6",
336 input-enable;
337 bias-pull-down;
348 pins = "GPIO34_R17";
349 input-enable;
350 bias-pull-down;
354 /* Modem I2C setup (SCL and SDA pins) */
362 pins = "GPIO40_T19",
364 input-enable;
365 bias-pull-down;
370 * Clock output pins associated with regulators.
379 pins = "GPIO1_T10";
380 input-enable;
381 bias-disable;
390 pins = "GPIO1_T10";
391 input-enable;
392 bias-pull-down;
403 pins = "GPIO3_U9";
404 input-enable;
405 bias-disable;
414 pins = "GPIO3_U9";
415 input-enable;
416 bias-pull-down;