1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com> 4 <http://rt2x00.serialmonkey.com> 5 6 */ 7 8 /* 9 Module: rt2500pci 10 Abstract: Data structures and registers for the rt2500pci module. 11 Supported chipsets: RT2560. 12 */ 13 14 #ifndef RT2500PCI_H 15 #define RT2500PCI_H 16 17 /* 18 * RF chip defines. 19 */ 20 #define RF2522 0x0000 21 #define RF2523 0x0001 22 #define RF2524 0x0002 23 #define RF2525 0x0003 24 #define RF2525E 0x0004 25 #define RF5222 0x0010 26 27 /* 28 * RT2560 version 29 */ 30 #define RT2560_VERSION_B 2 31 #define RT2560_VERSION_C 3 32 #define RT2560_VERSION_D 4 33 34 /* 35 * Signal information. 36 * Default offset is required for RSSI <-> dBm conversion. 37 */ 38 #define DEFAULT_RSSI_OFFSET 121 39 40 /* 41 * Register layout information. 42 */ 43 #define CSR_REG_BASE 0x0000 44 #define CSR_REG_SIZE 0x0174 45 #define EEPROM_BASE 0x0000 46 #define EEPROM_SIZE 0x0200 47 #define BBP_BASE 0x0000 48 #define BBP_SIZE 0x0040 49 #define RF_BASE 0x0004 50 #define RF_SIZE 0x0010 51 52 /* 53 * Number of TX queues. 54 */ 55 #define NUM_TX_QUEUES 2 56 57 /* 58 * Control/Status Registers(CSR). 59 * Some values are set in TU, whereas 1 TU == 1024 us. 60 */ 61 62 /* 63 * CSR0: ASIC revision number. 64 */ 65 #define CSR0 0x0000 66 #define CSR0_REVISION FIELD32(0x0000ffff) 67 68 /* 69 * CSR1: System control register. 70 * SOFT_RESET: Software reset, 1: reset, 0: normal. 71 * BBP_RESET: Hardware reset, 1: reset, 0, release. 72 * HOST_READY: Host ready after initialization. 73 */ 74 #define CSR1 0x0004 75 #define CSR1_SOFT_RESET FIELD32(0x00000001) 76 #define CSR1_BBP_RESET FIELD32(0x00000002) 77 #define CSR1_HOST_READY FIELD32(0x00000004) 78 79 /* 80 * CSR2: System admin status register (invalid). 81 */ 82 #define CSR2 0x0008 83 84 /* 85 * CSR3: STA MAC address register 0. 86 */ 87 #define CSR3 0x000c 88 #define CSR3_BYTE0 FIELD32(0x000000ff) 89 #define CSR3_BYTE1 FIELD32(0x0000ff00) 90 #define CSR3_BYTE2 FIELD32(0x00ff0000) 91 #define CSR3_BYTE3 FIELD32(0xff000000) 92 93 /* 94 * CSR4: STA MAC address register 1. 95 */ 96 #define CSR4 0x0010 97 #define CSR4_BYTE4 FIELD32(0x000000ff) 98 #define CSR4_BYTE5 FIELD32(0x0000ff00) 99 100 /* 101 * CSR5: BSSID register 0. 102 */ 103 #define CSR5 0x0014 104 #define CSR5_BYTE0 FIELD32(0x000000ff) 105 #define CSR5_BYTE1 FIELD32(0x0000ff00) 106 #define CSR5_BYTE2 FIELD32(0x00ff0000) 107 #define CSR5_BYTE3 FIELD32(0xff000000) 108 109 /* 110 * CSR6: BSSID register 1. 111 */ 112 #define CSR6 0x0018 113 #define CSR6_BYTE4 FIELD32(0x000000ff) 114 #define CSR6_BYTE5 FIELD32(0x0000ff00) 115 116 /* 117 * CSR7: Interrupt source register. 118 * Write 1 to clear. 119 * TBCN_EXPIRE: Beacon timer expired interrupt. 120 * TWAKE_EXPIRE: Wakeup timer expired interrupt. 121 * TATIMW_EXPIRE: Timer of atim window expired interrupt. 122 * TXDONE_TXRING: Tx ring transmit done interrupt. 123 * TXDONE_ATIMRING: Atim ring transmit done interrupt. 124 * TXDONE_PRIORING: Priority ring transmit done interrupt. 125 * RXDONE: Receive done interrupt. 126 * DECRYPTION_DONE: Decryption done interrupt. 127 * ENCRYPTION_DONE: Encryption done interrupt. 128 * UART1_TX_TRESHOLD: UART1 TX reaches threshold. 129 * UART1_RX_TRESHOLD: UART1 RX reaches threshold. 130 * UART1_IDLE_TRESHOLD: UART1 IDLE over threshold. 131 * UART1_TX_BUFF_ERROR: UART1 TX buffer error. 132 * UART1_RX_BUFF_ERROR: UART1 RX buffer error. 133 * UART2_TX_TRESHOLD: UART2 TX reaches threshold. 134 * UART2_RX_TRESHOLD: UART2 RX reaches threshold. 135 * UART2_IDLE_TRESHOLD: UART2 IDLE over threshold. 136 * UART2_TX_BUFF_ERROR: UART2 TX buffer error. 137 * UART2_RX_BUFF_ERROR: UART2 RX buffer error. 138 * TIMER_CSR3_EXPIRE: TIMECSR3 timer expired (802.1H quiet period). 139 140 */ 141 #define CSR7 0x001c 142 #define CSR7_TBCN_EXPIRE FIELD32(0x00000001) 143 #define CSR7_TWAKE_EXPIRE FIELD32(0x00000002) 144 #define CSR7_TATIMW_EXPIRE FIELD32(0x00000004) 145 #define CSR7_TXDONE_TXRING FIELD32(0x00000008) 146 #define CSR7_TXDONE_ATIMRING FIELD32(0x00000010) 147 #define CSR7_TXDONE_PRIORING FIELD32(0x00000020) 148 #define CSR7_RXDONE FIELD32(0x00000040) 149 #define CSR7_DECRYPTION_DONE FIELD32(0x00000080) 150 #define CSR7_ENCRYPTION_DONE FIELD32(0x00000100) 151 #define CSR7_UART1_TX_TRESHOLD FIELD32(0x00000200) 152 #define CSR7_UART1_RX_TRESHOLD FIELD32(0x00000400) 153 #define CSR7_UART1_IDLE_TRESHOLD FIELD32(0x00000800) 154 #define CSR7_UART1_TX_BUFF_ERROR FIELD32(0x00001000) 155 #define CSR7_UART1_RX_BUFF_ERROR FIELD32(0x00002000) 156 #define CSR7_UART2_TX_TRESHOLD FIELD32(0x00004000) 157 #define CSR7_UART2_RX_TRESHOLD FIELD32(0x00008000) 158 #define CSR7_UART2_IDLE_TRESHOLD FIELD32(0x00010000) 159 #define CSR7_UART2_TX_BUFF_ERROR FIELD32(0x00020000) 160 #define CSR7_UART2_RX_BUFF_ERROR FIELD32(0x00040000) 161 #define CSR7_TIMER_CSR3_EXPIRE FIELD32(0x00080000) 162 163 /* 164 * CSR8: Interrupt mask register. 165 * Write 1 to mask interrupt. 166 * TBCN_EXPIRE: Beacon timer expired interrupt. 167 * TWAKE_EXPIRE: Wakeup timer expired interrupt. 168 * TATIMW_EXPIRE: Timer of atim window expired interrupt. 169 * TXDONE_TXRING: Tx ring transmit done interrupt. 170 * TXDONE_ATIMRING: Atim ring transmit done interrupt. 171 * TXDONE_PRIORING: Priority ring transmit done interrupt. 172 * RXDONE: Receive done interrupt. 173 * DECRYPTION_DONE: Decryption done interrupt. 174 * ENCRYPTION_DONE: Encryption done interrupt. 175 * UART1_TX_TRESHOLD: UART1 TX reaches threshold. 176 * UART1_RX_TRESHOLD: UART1 RX reaches threshold. 177 * UART1_IDLE_TRESHOLD: UART1 IDLE over threshold. 178 * UART1_TX_BUFF_ERROR: UART1 TX buffer error. 179 * UART1_RX_BUFF_ERROR: UART1 RX buffer error. 180 * UART2_TX_TRESHOLD: UART2 TX reaches threshold. 181 * UART2_RX_TRESHOLD: UART2 RX reaches threshold. 182 * UART2_IDLE_TRESHOLD: UART2 IDLE over threshold. 183 * UART2_TX_BUFF_ERROR: UART2 TX buffer error. 184 * UART2_RX_BUFF_ERROR: UART2 RX buffer error. 185 * TIMER_CSR3_EXPIRE: TIMECSR3 timer expired (802.1H quiet period). 186 */ 187 #define CSR8 0x0020 188 #define CSR8_TBCN_EXPIRE FIELD32(0x00000001) 189 #define CSR8_TWAKE_EXPIRE FIELD32(0x00000002) 190 #define CSR8_TATIMW_EXPIRE FIELD32(0x00000004) 191 #define CSR8_TXDONE_TXRING FIELD32(0x00000008) 192 #define CSR8_TXDONE_ATIMRING FIELD32(0x00000010) 193 #define CSR8_TXDONE_PRIORING FIELD32(0x00000020) 194 #define CSR8_RXDONE FIELD32(0x00000040) 195 #define CSR8_DECRYPTION_DONE FIELD32(0x00000080) 196 #define CSR8_ENCRYPTION_DONE FIELD32(0x00000100) 197 #define CSR8_UART1_TX_TRESHOLD FIELD32(0x00000200) 198 #define CSR8_UART1_RX_TRESHOLD FIELD32(0x00000400) 199 #define CSR8_UART1_IDLE_TRESHOLD FIELD32(0x00000800) 200 #define CSR8_UART1_TX_BUFF_ERROR FIELD32(0x00001000) 201 #define CSR8_UART1_RX_BUFF_ERROR FIELD32(0x00002000) 202 #define CSR8_UART2_TX_TRESHOLD FIELD32(0x00004000) 203 #define CSR8_UART2_RX_TRESHOLD FIELD32(0x00008000) 204 #define CSR8_UART2_IDLE_TRESHOLD FIELD32(0x00010000) 205 #define CSR8_UART2_TX_BUFF_ERROR FIELD32(0x00020000) 206 #define CSR8_UART2_RX_BUFF_ERROR FIELD32(0x00040000) 207 #define CSR8_TIMER_CSR3_EXPIRE FIELD32(0x00080000) 208 209 /* 210 * CSR9: Maximum frame length register. 211 * MAX_FRAME_UNIT: Maximum frame length in 128b unit, default: 12. 212 */ 213 #define CSR9 0x0024 214 #define CSR9_MAX_FRAME_UNIT FIELD32(0x00000f80) 215 216 /* 217 * SECCSR0: WEP control register. 218 * KICK_DECRYPT: Kick decryption engine, self-clear. 219 * ONE_SHOT: 0: ring mode, 1: One shot only mode. 220 * DESC_ADDRESS: Descriptor physical address of frame. 221 */ 222 #define SECCSR0 0x0028 223 #define SECCSR0_KICK_DECRYPT FIELD32(0x00000001) 224 #define SECCSR0_ONE_SHOT FIELD32(0x00000002) 225 #define SECCSR0_DESC_ADDRESS FIELD32(0xfffffffc) 226 227 /* 228 * CSR11: Back-off control register. 229 * CWMIN: CWmin. Default cwmin is 31 (2^5 - 1). 230 * CWMAX: CWmax. Default cwmax is 1023 (2^10 - 1). 231 * SLOT_TIME: Slot time, default is 20us for 802.11b 232 * CW_SELECT: CWmin/CWmax selection, 1: Register, 0: TXD. 233 * LONG_RETRY: Long retry count. 234 * SHORT_RETRY: Short retry count. 235 */ 236 #define CSR11 0x002c 237 #define CSR11_CWMIN FIELD32(0x0000000f) 238 #define CSR11_CWMAX FIELD32(0x000000f0) 239 #define CSR11_SLOT_TIME FIELD32(0x00001f00) 240 #define CSR11_CW_SELECT FIELD32(0x00002000) 241 #define CSR11_LONG_RETRY FIELD32(0x00ff0000) 242 #define CSR11_SHORT_RETRY FIELD32(0xff000000) 243 244 /* 245 * CSR12: Synchronization configuration register 0. 246 * All units in 1/16 TU. 247 * BEACON_INTERVAL: Beacon interval, default is 100 TU. 248 * CFP_MAX_DURATION: Cfp maximum duration, default is 100 TU. 249 */ 250 #define CSR12 0x0030 251 #define CSR12_BEACON_INTERVAL FIELD32(0x0000ffff) 252 #define CSR12_CFP_MAX_DURATION FIELD32(0xffff0000) 253 254 /* 255 * CSR13: Synchronization configuration register 1. 256 * All units in 1/16 TU. 257 * ATIMW_DURATION: Atim window duration. 258 * CFP_PERIOD: Cfp period, default is 0 TU. 259 */ 260 #define CSR13 0x0034 261 #define CSR13_ATIMW_DURATION FIELD32(0x0000ffff) 262 #define CSR13_CFP_PERIOD FIELD32(0x00ff0000) 263 264 /* 265 * CSR14: Synchronization control register. 266 * TSF_COUNT: Enable tsf auto counting. 267 * TSF_SYNC: Tsf sync, 0: disable, 1: infra, 2: ad-hoc/master mode. 268 * TBCN: Enable tbcn with reload value. 269 * TCFP: Enable tcfp & cfp / cp switching. 270 * TATIMW: Enable tatimw & atim window switching. 271 * BEACON_GEN: Enable beacon generator. 272 * CFP_COUNT_PRELOAD: Cfp count preload value. 273 * TBCM_PRELOAD: Tbcn preload value in units of 64us. 274 */ 275 #define CSR14 0x0038 276 #define CSR14_TSF_COUNT FIELD32(0x00000001) 277 #define CSR14_TSF_SYNC FIELD32(0x00000006) 278 #define CSR14_TBCN FIELD32(0x00000008) 279 #define CSR14_TCFP FIELD32(0x00000010) 280 #define CSR14_TATIMW FIELD32(0x00000020) 281 #define CSR14_BEACON_GEN FIELD32(0x00000040) 282 #define CSR14_CFP_COUNT_PRELOAD FIELD32(0x0000ff00) 283 #define CSR14_TBCM_PRELOAD FIELD32(0xffff0000) 284 285 /* 286 * CSR15: Synchronization status register. 287 * CFP: ASIC is in contention-free period. 288 * ATIMW: ASIC is in ATIM window. 289 * BEACON_SENT: Beacon is send. 290 */ 291 #define CSR15 0x003c 292 #define CSR15_CFP FIELD32(0x00000001) 293 #define CSR15_ATIMW FIELD32(0x00000002) 294 #define CSR15_BEACON_SENT FIELD32(0x00000004) 295 296 /* 297 * CSR16: TSF timer register 0. 298 */ 299 #define CSR16 0x0040 300 #define CSR16_LOW_TSFTIMER FIELD32(0xffffffff) 301 302 /* 303 * CSR17: TSF timer register 1. 304 */ 305 #define CSR17 0x0044 306 #define CSR17_HIGH_TSFTIMER FIELD32(0xffffffff) 307 308 /* 309 * CSR18: IFS timer register 0. 310 * SIFS: Sifs, default is 10 us. 311 * PIFS: Pifs, default is 30 us. 312 */ 313 #define CSR18 0x0048 314 #define CSR18_SIFS FIELD32(0x000001ff) 315 #define CSR18_PIFS FIELD32(0x001f0000) 316 317 /* 318 * CSR19: IFS timer register 1. 319 * DIFS: Difs, default is 50 us. 320 * EIFS: Eifs, default is 364 us. 321 */ 322 #define CSR19 0x004c 323 #define CSR19_DIFS FIELD32(0x0000ffff) 324 #define CSR19_EIFS FIELD32(0xffff0000) 325 326 /* 327 * CSR20: Wakeup timer register. 328 * DELAY_AFTER_TBCN: Delay after tbcn expired in units of 1/16 TU. 329 * TBCN_BEFORE_WAKEUP: Number of beacon before wakeup. 330 * AUTOWAKE: Enable auto wakeup / sleep mechanism. 331 */ 332 #define CSR20 0x0050 333 #define CSR20_DELAY_AFTER_TBCN FIELD32(0x0000ffff) 334 #define CSR20_TBCN_BEFORE_WAKEUP FIELD32(0x00ff0000) 335 #define CSR20_AUTOWAKE FIELD32(0x01000000) 336 337 /* 338 * CSR21: EEPROM control register. 339 * RELOAD: Write 1 to reload eeprom content. 340 * TYPE_93C46: 1: 93c46, 0:93c66. 341 */ 342 #define CSR21 0x0054 343 #define CSR21_RELOAD FIELD32(0x00000001) 344 #define CSR21_EEPROM_DATA_CLOCK FIELD32(0x00000002) 345 #define CSR21_EEPROM_CHIP_SELECT FIELD32(0x00000004) 346 #define CSR21_EEPROM_DATA_IN FIELD32(0x00000008) 347 #define CSR21_EEPROM_DATA_OUT FIELD32(0x00000010) 348 #define CSR21_TYPE_93C46 FIELD32(0x00000020) 349 350 /* 351 * CSR22: CFP control register. 352 * CFP_DURATION_REMAIN: Cfp duration remain, in units of TU. 353 * RELOAD_CFP_DURATION: Write 1 to reload cfp duration remain. 354 */ 355 #define CSR22 0x0058 356 #define CSR22_CFP_DURATION_REMAIN FIELD32(0x0000ffff) 357 #define CSR22_RELOAD_CFP_DURATION FIELD32(0x00010000) 358 359 /* 360 * Transmit related CSRs. 361 * Some values are set in TU, whereas 1 TU == 1024 us. 362 */ 363 364 /* 365 * TXCSR0: TX Control Register. 366 * KICK_TX: Kick tx ring. 367 * KICK_ATIM: Kick atim ring. 368 * KICK_PRIO: Kick priority ring. 369 * ABORT: Abort all transmit related ring operation. 370 */ 371 #define TXCSR0 0x0060 372 #define TXCSR0_KICK_TX FIELD32(0x00000001) 373 #define TXCSR0_KICK_ATIM FIELD32(0x00000002) 374 #define TXCSR0_KICK_PRIO FIELD32(0x00000004) 375 #define TXCSR0_ABORT FIELD32(0x00000008) 376 377 /* 378 * TXCSR1: TX Configuration Register. 379 * ACK_TIMEOUT: Ack timeout, default = sifs + 2*slottime + acktime @ 1mbps. 380 * ACK_CONSUME_TIME: Ack consume time, default = sifs + acktime @ 1mbps. 381 * TSF_OFFSET: Insert tsf offset. 382 * AUTORESPONDER: Enable auto responder which include ack & cts. 383 */ 384 #define TXCSR1 0x0064 385 #define TXCSR1_ACK_TIMEOUT FIELD32(0x000001ff) 386 #define TXCSR1_ACK_CONSUME_TIME FIELD32(0x0003fe00) 387 #define TXCSR1_TSF_OFFSET FIELD32(0x00fc0000) 388 #define TXCSR1_AUTORESPONDER FIELD32(0x01000000) 389 390 /* 391 * TXCSR2: Tx descriptor configuration register. 392 * TXD_SIZE: Tx descriptor size, default is 48. 393 * NUM_TXD: Number of tx entries in ring. 394 * NUM_ATIM: Number of atim entries in ring. 395 * NUM_PRIO: Number of priority entries in ring. 396 */ 397 #define TXCSR2 0x0068 398 #define TXCSR2_TXD_SIZE FIELD32(0x000000ff) 399 #define TXCSR2_NUM_TXD FIELD32(0x0000ff00) 400 #define TXCSR2_NUM_ATIM FIELD32(0x00ff0000) 401 #define TXCSR2_NUM_PRIO FIELD32(0xff000000) 402 403 /* 404 * TXCSR3: TX Ring Base address register. 405 */ 406 #define TXCSR3 0x006c 407 #define TXCSR3_TX_RING_REGISTER FIELD32(0xffffffff) 408 409 /* 410 * TXCSR4: TX Atim Ring Base address register. 411 */ 412 #define TXCSR4 0x0070 413 #define TXCSR4_ATIM_RING_REGISTER FIELD32(0xffffffff) 414 415 /* 416 * TXCSR5: TX Prio Ring Base address register. 417 */ 418 #define TXCSR5 0x0074 419 #define TXCSR5_PRIO_RING_REGISTER FIELD32(0xffffffff) 420 421 /* 422 * TXCSR6: Beacon Base address register. 423 */ 424 #define TXCSR6 0x0078 425 #define TXCSR6_BEACON_RING_REGISTER FIELD32(0xffffffff) 426 427 /* 428 * TXCSR7: Auto responder control register. 429 * AR_POWERMANAGEMENT: Auto responder power management bit. 430 */ 431 #define TXCSR7 0x007c 432 #define TXCSR7_AR_POWERMANAGEMENT FIELD32(0x00000001) 433 434 /* 435 * TXCSR8: CCK Tx BBP register. 436 */ 437 #define TXCSR8 0x0098 438 #define TXCSR8_BBP_ID0 FIELD32(0x0000007f) 439 #define TXCSR8_BBP_ID0_VALID FIELD32(0x00000080) 440 #define TXCSR8_BBP_ID1 FIELD32(0x00007f00) 441 #define TXCSR8_BBP_ID1_VALID FIELD32(0x00008000) 442 #define TXCSR8_BBP_ID2 FIELD32(0x007f0000) 443 #define TXCSR8_BBP_ID2_VALID FIELD32(0x00800000) 444 #define TXCSR8_BBP_ID3 FIELD32(0x7f000000) 445 #define TXCSR8_BBP_ID3_VALID FIELD32(0x80000000) 446 447 /* 448 * TXCSR9: OFDM TX BBP registers 449 * OFDM_SIGNAL: BBP rate field address for OFDM. 450 * OFDM_SERVICE: BBP service field address for OFDM. 451 * OFDM_LENGTH_LOW: BBP length low byte address for OFDM. 452 * OFDM_LENGTH_HIGH: BBP length high byte address for OFDM. 453 */ 454 #define TXCSR9 0x0094 455 #define TXCSR9_OFDM_RATE FIELD32(0x000000ff) 456 #define TXCSR9_OFDM_SERVICE FIELD32(0x0000ff00) 457 #define TXCSR9_OFDM_LENGTH_LOW FIELD32(0x00ff0000) 458 #define TXCSR9_OFDM_LENGTH_HIGH FIELD32(0xff000000) 459 460 /* 461 * Receive related CSRs. 462 * Some values are set in TU, whereas 1 TU == 1024 us. 463 */ 464 465 /* 466 * RXCSR0: RX Control Register. 467 * DISABLE_RX: Disable rx engine. 468 * DROP_CRC: Drop crc error. 469 * DROP_PHYSICAL: Drop physical error. 470 * DROP_CONTROL: Drop control frame. 471 * DROP_NOT_TO_ME: Drop not to me unicast frame. 472 * DROP_TODS: Drop frame tods bit is true. 473 * DROP_VERSION_ERROR: Drop version error frame. 474 * PASS_CRC: Pass all packets with crc attached. 475 * PASS_CRC: Pass all packets with crc attached. 476 * PASS_PLCP: Pass all packets with 4 bytes PLCP attached. 477 * DROP_MCAST: Drop multicast frames. 478 * DROP_BCAST: Drop broadcast frames. 479 * ENABLE_QOS: Accept QOS data frame and parse QOS field. 480 */ 481 #define RXCSR0 0x0080 482 #define RXCSR0_DISABLE_RX FIELD32(0x00000001) 483 #define RXCSR0_DROP_CRC FIELD32(0x00000002) 484 #define RXCSR0_DROP_PHYSICAL FIELD32(0x00000004) 485 #define RXCSR0_DROP_CONTROL FIELD32(0x00000008) 486 #define RXCSR0_DROP_NOT_TO_ME FIELD32(0x00000010) 487 #define RXCSR0_DROP_TODS FIELD32(0x00000020) 488 #define RXCSR0_DROP_VERSION_ERROR FIELD32(0x00000040) 489 #define RXCSR0_PASS_CRC FIELD32(0x00000080) 490 #define RXCSR0_PASS_PLCP FIELD32(0x00000100) 491 #define RXCSR0_DROP_MCAST FIELD32(0x00000200) 492 #define RXCSR0_DROP_BCAST FIELD32(0x00000400) 493 #define RXCSR0_ENABLE_QOS FIELD32(0x00000800) 494 495 /* 496 * RXCSR1: RX descriptor configuration register. 497 * RXD_SIZE: Rx descriptor size, default is 32b. 498 * NUM_RXD: Number of rx entries in ring. 499 */ 500 #define RXCSR1 0x0084 501 #define RXCSR1_RXD_SIZE FIELD32(0x000000ff) 502 #define RXCSR1_NUM_RXD FIELD32(0x0000ff00) 503 504 /* 505 * RXCSR2: RX Ring base address register. 506 */ 507 #define RXCSR2 0x0088 508 #define RXCSR2_RX_RING_REGISTER FIELD32(0xffffffff) 509 510 /* 511 * RXCSR3: BBP ID register for Rx operation. 512 * BBP_ID#: BBP register # id. 513 * BBP_ID#_VALID: BBP register # id is valid or not. 514 */ 515 #define RXCSR3 0x0090 516 #define RXCSR3_BBP_ID0 FIELD32(0x0000007f) 517 #define RXCSR3_BBP_ID0_VALID FIELD32(0x00000080) 518 #define RXCSR3_BBP_ID1 FIELD32(0x00007f00) 519 #define RXCSR3_BBP_ID1_VALID FIELD32(0x00008000) 520 #define RXCSR3_BBP_ID2 FIELD32(0x007f0000) 521 #define RXCSR3_BBP_ID2_VALID FIELD32(0x00800000) 522 #define RXCSR3_BBP_ID3 FIELD32(0x7f000000) 523 #define RXCSR3_BBP_ID3_VALID FIELD32(0x80000000) 524 525 /* 526 * ARCSR1: Auto Responder PLCP config register 1. 527 * AR_BBP_DATA#: Auto responder BBP register # data. 528 * AR_BBP_ID#: Auto responder BBP register # Id. 529 */ 530 #define ARCSR1 0x009c 531 #define ARCSR1_AR_BBP_DATA2 FIELD32(0x000000ff) 532 #define ARCSR1_AR_BBP_ID2 FIELD32(0x0000ff00) 533 #define ARCSR1_AR_BBP_DATA3 FIELD32(0x00ff0000) 534 #define ARCSR1_AR_BBP_ID3 FIELD32(0xff000000) 535 536 /* 537 * Miscellaneous Registers. 538 * Some values are set in TU, whereas 1 TU == 1024 us. 539 540 */ 541 542 /* 543 * PCICSR: PCI control register. 544 * BIG_ENDIAN: 1: big endian, 0: little endian. 545 * RX_TRESHOLD: Rx threshold in dw to start pci access 546 * 0: 16dw (default), 1: 8dw, 2: 4dw, 3: 32dw. 547 * TX_TRESHOLD: Tx threshold in dw to start pci access 548 * 0: 0dw (default), 1: 1dw, 2: 4dw, 3: forward. 549 * BURST_LENTH: Pci burst length 0: 4dw (default, 1: 8dw, 2: 16dw, 3:32dw. 550 * ENABLE_CLK: Enable clk_run, pci clock can't going down to non-operational. 551 * READ_MULTIPLE: Enable memory read multiple. 552 * WRITE_INVALID: Enable memory write & invalid. 553 */ 554 #define PCICSR 0x008c 555 #define PCICSR_BIG_ENDIAN FIELD32(0x00000001) 556 #define PCICSR_RX_TRESHOLD FIELD32(0x00000006) 557 #define PCICSR_TX_TRESHOLD FIELD32(0x00000018) 558 #define PCICSR_BURST_LENTH FIELD32(0x00000060) 559 #define PCICSR_ENABLE_CLK FIELD32(0x00000080) 560 #define PCICSR_READ_MULTIPLE FIELD32(0x00000100) 561 #define PCICSR_WRITE_INVALID FIELD32(0x00000200) 562 563 /* 564 * CNT0: FCS error count. 565 * FCS_ERROR: FCS error count, cleared when read. 566 */ 567 #define CNT0 0x00a0 568 #define CNT0_FCS_ERROR FIELD32(0x0000ffff) 569 570 /* 571 * Statistic Register. 572 * CNT1: PLCP error count. 573 * CNT2: Long error count. 574 */ 575 #define TIMECSR2 0x00a8 576 #define CNT1 0x00ac 577 #define CNT2 0x00b0 578 #define TIMECSR3 0x00b4 579 580 /* 581 * CNT3: CCA false alarm count. 582 */ 583 #define CNT3 0x00b8 584 #define CNT3_FALSE_CCA FIELD32(0x0000ffff) 585 586 /* 587 * Statistic Register. 588 * CNT4: Rx FIFO overflow count. 589 * CNT5: Tx FIFO underrun count. 590 */ 591 #define CNT4 0x00bc 592 #define CNT5 0x00c0 593 594 /* 595 * Baseband Control Register. 596 */ 597 598 /* 599 * PWRCSR0: Power mode configuration register. 600 */ 601 #define PWRCSR0 0x00c4 602 603 /* 604 * Power state transition time registers. 605 */ 606 #define PSCSR0 0x00c8 607 #define PSCSR1 0x00cc 608 #define PSCSR2 0x00d0 609 #define PSCSR3 0x00d4 610 611 /* 612 * PWRCSR1: Manual power control / status register. 613 * Allowed state: 0 deep_sleep, 1: sleep, 2: standby, 3: awake. 614 * SET_STATE: Set state. Write 1 to trigger, self cleared. 615 * BBP_DESIRE_STATE: BBP desired state. 616 * RF_DESIRE_STATE: RF desired state. 617 * BBP_CURR_STATE: BBP current state. 618 * RF_CURR_STATE: RF current state. 619 * PUT_TO_SLEEP: Put to sleep. Write 1 to trigger, self cleared. 620 */ 621 #define PWRCSR1 0x00d8 622 #define PWRCSR1_SET_STATE FIELD32(0x00000001) 623 #define PWRCSR1_BBP_DESIRE_STATE FIELD32(0x00000006) 624 #define PWRCSR1_RF_DESIRE_STATE FIELD32(0x00000018) 625 #define PWRCSR1_BBP_CURR_STATE FIELD32(0x00000060) 626 #define PWRCSR1_RF_CURR_STATE FIELD32(0x00000180) 627 #define PWRCSR1_PUT_TO_SLEEP FIELD32(0x00000200) 628 629 /* 630 * TIMECSR: Timer control register. 631 * US_COUNT: 1 us timer count in units of clock cycles. 632 * US_64_COUNT: 64 us timer count in units of 1 us timer. 633 * BEACON_EXPECT: Beacon expect window. 634 */ 635 #define TIMECSR 0x00dc 636 #define TIMECSR_US_COUNT FIELD32(0x000000ff) 637 #define TIMECSR_US_64_COUNT FIELD32(0x0000ff00) 638 #define TIMECSR_BEACON_EXPECT FIELD32(0x00070000) 639 640 /* 641 * MACCSR0: MAC configuration register 0. 642 */ 643 #define MACCSR0 0x00e0 644 645 /* 646 * MACCSR1: MAC configuration register 1. 647 * KICK_RX: Kick one-shot rx in one-shot rx mode. 648 * ONESHOT_RXMODE: Enable one-shot rx mode for debugging. 649 * BBPRX_RESET_MODE: Ralink bbp rx reset mode. 650 * AUTO_TXBBP: Auto tx logic access bbp control register. 651 * AUTO_RXBBP: Auto rx logic access bbp control register. 652 * LOOPBACK: Loopback mode. 0: normal, 1: internal, 2: external, 3:rsvd. 653 * INTERSIL_IF: Intersil if calibration pin. 654 */ 655 #define MACCSR1 0x00e4 656 #define MACCSR1_KICK_RX FIELD32(0x00000001) 657 #define MACCSR1_ONESHOT_RXMODE FIELD32(0x00000002) 658 #define MACCSR1_BBPRX_RESET_MODE FIELD32(0x00000004) 659 #define MACCSR1_AUTO_TXBBP FIELD32(0x00000008) 660 #define MACCSR1_AUTO_RXBBP FIELD32(0x00000010) 661 #define MACCSR1_LOOPBACK FIELD32(0x00000060) 662 #define MACCSR1_INTERSIL_IF FIELD32(0x00000080) 663 664 /* 665 * RALINKCSR: Ralink Rx auto-reset BBCR. 666 * AR_BBP_DATA#: Auto reset BBP register # data. 667 * AR_BBP_ID#: Auto reset BBP register # id. 668 */ 669 #define RALINKCSR 0x00e8 670 #define RALINKCSR_AR_BBP_DATA0 FIELD32(0x000000ff) 671 #define RALINKCSR_AR_BBP_ID0 FIELD32(0x00007f00) 672 #define RALINKCSR_AR_BBP_VALID0 FIELD32(0x00008000) 673 #define RALINKCSR_AR_BBP_DATA1 FIELD32(0x00ff0000) 674 #define RALINKCSR_AR_BBP_ID1 FIELD32(0x7f000000) 675 #define RALINKCSR_AR_BBP_VALID1 FIELD32(0x80000000) 676 677 /* 678 * BCNCSR: Beacon interval control register. 679 * CHANGE: Write one to change beacon interval. 680 * DELTATIME: The delta time value. 681 * NUM_BEACON: Number of beacon according to mode. 682 * MODE: Please refer to asic specs. 683 * PLUS: Plus or minus delta time value. 684 */ 685 #define BCNCSR 0x00ec 686 #define BCNCSR_CHANGE FIELD32(0x00000001) 687 #define BCNCSR_DELTATIME FIELD32(0x0000001e) 688 #define BCNCSR_NUM_BEACON FIELD32(0x00001fe0) 689 #define BCNCSR_MODE FIELD32(0x00006000) 690 #define BCNCSR_PLUS FIELD32(0x00008000) 691 692 /* 693 * BBP / RF / IF Control Register. 694 */ 695 696 /* 697 * BBPCSR: BBP serial control register. 698 * VALUE: Register value to program into BBP. 699 * REGNUM: Selected BBP register. 700 * BUSY: 1: asic is busy execute BBP programming. 701 * WRITE_CONTROL: 1: write BBP, 0: read BBP. 702 */ 703 #define BBPCSR 0x00f0 704 #define BBPCSR_VALUE FIELD32(0x000000ff) 705 #define BBPCSR_REGNUM FIELD32(0x00007f00) 706 #define BBPCSR_BUSY FIELD32(0x00008000) 707 #define BBPCSR_WRITE_CONTROL FIELD32(0x00010000) 708 709 /* 710 * RFCSR: RF serial control register. 711 * VALUE: Register value + id to program into rf/if. 712 * NUMBER_OF_BITS: Number of bits used in value (i:20, rfmd:22). 713 * IF_SELECT: Chip to program: 0: rf, 1: if. 714 * PLL_LD: Rf pll_ld status. 715 * BUSY: 1: asic is busy execute rf programming. 716 */ 717 #define RFCSR 0x00f4 718 #define RFCSR_VALUE FIELD32(0x00ffffff) 719 #define RFCSR_NUMBER_OF_BITS FIELD32(0x1f000000) 720 #define RFCSR_IF_SELECT FIELD32(0x20000000) 721 #define RFCSR_PLL_LD FIELD32(0x40000000) 722 #define RFCSR_BUSY FIELD32(0x80000000) 723 724 /* 725 * LEDCSR: LED control register. 726 * ON_PERIOD: On period, default 70ms. 727 * OFF_PERIOD: Off period, default 30ms. 728 * LINK: 0: linkoff, 1: linkup. 729 * ACTIVITY: 0: idle, 1: active. 730 * LINK_POLARITY: 0: active low, 1: active high. 731 * ACTIVITY_POLARITY: 0: active low, 1: active high. 732 * LED_DEFAULT: LED state for "enable" 0: ON, 1: OFF. 733 */ 734 #define LEDCSR 0x00f8 735 #define LEDCSR_ON_PERIOD FIELD32(0x000000ff) 736 #define LEDCSR_OFF_PERIOD FIELD32(0x0000ff00) 737 #define LEDCSR_LINK FIELD32(0x00010000) 738 #define LEDCSR_ACTIVITY FIELD32(0x00020000) 739 #define LEDCSR_LINK_POLARITY FIELD32(0x00040000) 740 #define LEDCSR_ACTIVITY_POLARITY FIELD32(0x00080000) 741 #define LEDCSR_LED_DEFAULT FIELD32(0x00100000) 742 743 /* 744 * SECCSR3: AES control register. 745 */ 746 #define SECCSR3 0x00fc 747 748 /* 749 * ASIC pointer information. 750 * RXPTR: Current RX ring address. 751 * TXPTR: Current Tx ring address. 752 * PRIPTR: Current Priority ring address. 753 * ATIMPTR: Current ATIM ring address. 754 */ 755 #define RXPTR 0x0100 756 #define TXPTR 0x0104 757 #define PRIPTR 0x0108 758 #define ATIMPTR 0x010c 759 760 /* 761 * TXACKCSR0: TX ACK timeout. 762 */ 763 #define TXACKCSR0 0x0110 764 765 /* 766 * ACK timeout count registers. 767 * ACKCNT0: TX ACK timeout count. 768 * ACKCNT1: RX ACK timeout count. 769 */ 770 #define ACKCNT0 0x0114 771 #define ACKCNT1 0x0118 772 773 /* 774 * GPIO and others. 775 */ 776 777 /* 778 * GPIOCSR: GPIO control register. 779 * GPIOCSR_VALx: GPIO value 780 * GPIOCSR_DIRx: GPIO direction: 0 = output; 1 = input 781 */ 782 #define GPIOCSR 0x0120 783 #define GPIOCSR_VAL0 FIELD32(0x00000001) 784 #define GPIOCSR_VAL1 FIELD32(0x00000002) 785 #define GPIOCSR_VAL2 FIELD32(0x00000004) 786 #define GPIOCSR_VAL3 FIELD32(0x00000008) 787 #define GPIOCSR_VAL4 FIELD32(0x00000010) 788 #define GPIOCSR_VAL5 FIELD32(0x00000020) 789 #define GPIOCSR_VAL6 FIELD32(0x00000040) 790 #define GPIOCSR_VAL7 FIELD32(0x00000080) 791 #define GPIOCSR_DIR0 FIELD32(0x00000100) 792 #define GPIOCSR_DIR1 FIELD32(0x00000200) 793 #define GPIOCSR_DIR2 FIELD32(0x00000400) 794 #define GPIOCSR_DIR3 FIELD32(0x00000800) 795 #define GPIOCSR_DIR4 FIELD32(0x00001000) 796 #define GPIOCSR_DIR5 FIELD32(0x00002000) 797 #define GPIOCSR_DIR6 FIELD32(0x00004000) 798 #define GPIOCSR_DIR7 FIELD32(0x00008000) 799 800 /* 801 * FIFO pointer registers. 802 * FIFOCSR0: TX FIFO pointer. 803 * FIFOCSR1: RX FIFO pointer. 804 */ 805 #define FIFOCSR0 0x0128 806 #define FIFOCSR1 0x012c 807 808 /* 809 * BCNCSR1: Tx BEACON offset time control register. 810 * PRELOAD: Beacon timer offset in units of usec. 811 * BEACON_CWMIN: 2^CwMin. 812 */ 813 #define BCNCSR1 0x0130 814 #define BCNCSR1_PRELOAD FIELD32(0x0000ffff) 815 #define BCNCSR1_BEACON_CWMIN FIELD32(0x000f0000) 816 817 /* 818 * MACCSR2: TX_PE to RX_PE turn-around time control register 819 * DELAY: RX_PE low width, in units of pci clock cycle. 820 */ 821 #define MACCSR2 0x0134 822 #define MACCSR2_DELAY FIELD32(0x000000ff) 823 824 /* 825 * TESTCSR: TEST mode selection register. 826 */ 827 #define TESTCSR 0x0138 828 829 /* 830 * ARCSR2: 1 Mbps ACK/CTS PLCP. 831 */ 832 #define ARCSR2 0x013c 833 #define ARCSR2_SIGNAL FIELD32(0x000000ff) 834 #define ARCSR2_SERVICE FIELD32(0x0000ff00) 835 #define ARCSR2_LENGTH FIELD32(0xffff0000) 836 837 /* 838 * ARCSR3: 2 Mbps ACK/CTS PLCP. 839 */ 840 #define ARCSR3 0x0140 841 #define ARCSR3_SIGNAL FIELD32(0x000000ff) 842 #define ARCSR3_SERVICE FIELD32(0x0000ff00) 843 #define ARCSR3_LENGTH FIELD32(0xffff0000) 844 845 /* 846 * ARCSR4: 5.5 Mbps ACK/CTS PLCP. 847 */ 848 #define ARCSR4 0x0144 849 #define ARCSR4_SIGNAL FIELD32(0x000000ff) 850 #define ARCSR4_SERVICE FIELD32(0x0000ff00) 851 #define ARCSR4_LENGTH FIELD32(0xffff0000) 852 853 /* 854 * ARCSR5: 11 Mbps ACK/CTS PLCP. 855 */ 856 #define ARCSR5 0x0148 857 #define ARCSR5_SIGNAL FIELD32(0x000000ff) 858 #define ARCSR5_SERVICE FIELD32(0x0000ff00) 859 #define ARCSR5_LENGTH FIELD32(0xffff0000) 860 861 /* 862 * ARTCSR0: CCK ACK/CTS payload consumed time for 1/2/5.5/11 mbps. 863 */ 864 #define ARTCSR0 0x014c 865 #define ARTCSR0_ACK_CTS_11MBS FIELD32(0x000000ff) 866 #define ARTCSR0_ACK_CTS_5_5MBS FIELD32(0x0000ff00) 867 #define ARTCSR0_ACK_CTS_2MBS FIELD32(0x00ff0000) 868 #define ARTCSR0_ACK_CTS_1MBS FIELD32(0xff000000) 869 870 871 /* 872 * ARTCSR1: OFDM ACK/CTS payload consumed time for 6/9/12/18 mbps. 873 */ 874 #define ARTCSR1 0x0150 875 #define ARTCSR1_ACK_CTS_6MBS FIELD32(0x000000ff) 876 #define ARTCSR1_ACK_CTS_9MBS FIELD32(0x0000ff00) 877 #define ARTCSR1_ACK_CTS_12MBS FIELD32(0x00ff0000) 878 #define ARTCSR1_ACK_CTS_18MBS FIELD32(0xff000000) 879 880 /* 881 * ARTCSR2: OFDM ACK/CTS payload consumed time for 24/36/48/54 mbps. 882 */ 883 #define ARTCSR2 0x0154 884 #define ARTCSR2_ACK_CTS_24MBS FIELD32(0x000000ff) 885 #define ARTCSR2_ACK_CTS_36MBS FIELD32(0x0000ff00) 886 #define ARTCSR2_ACK_CTS_48MBS FIELD32(0x00ff0000) 887 #define ARTCSR2_ACK_CTS_54MBS FIELD32(0xff000000) 888 889 /* 890 * SECCSR1: WEP control register. 891 * KICK_ENCRYPT: Kick encryption engine, self-clear. 892 * ONE_SHOT: 0: ring mode, 1: One shot only mode. 893 * DESC_ADDRESS: Descriptor physical address of frame. 894 */ 895 #define SECCSR1 0x0158 896 #define SECCSR1_KICK_ENCRYPT FIELD32(0x00000001) 897 #define SECCSR1_ONE_SHOT FIELD32(0x00000002) 898 #define SECCSR1_DESC_ADDRESS FIELD32(0xfffffffc) 899 900 /* 901 * BBPCSR1: BBP TX configuration. 902 */ 903 #define BBPCSR1 0x015c 904 #define BBPCSR1_CCK FIELD32(0x00000003) 905 #define BBPCSR1_CCK_FLIP FIELD32(0x00000004) 906 #define BBPCSR1_OFDM FIELD32(0x00030000) 907 #define BBPCSR1_OFDM_FLIP FIELD32(0x00040000) 908 909 /* 910 * Dual band configuration registers. 911 * DBANDCSR0: Dual band configuration register 0. 912 * DBANDCSR1: Dual band configuration register 1. 913 */ 914 #define DBANDCSR0 0x0160 915 #define DBANDCSR1 0x0164 916 917 /* 918 * BBPPCSR: BBP Pin control register. 919 */ 920 #define BBPPCSR 0x0168 921 922 /* 923 * MAC special debug mode selection registers. 924 * DBGSEL0: MAC special debug mode selection register 0. 925 * DBGSEL1: MAC special debug mode selection register 1. 926 */ 927 #define DBGSEL0 0x016c 928 #define DBGSEL1 0x0170 929 930 /* 931 * BISTCSR: BBP BIST register. 932 */ 933 #define BISTCSR 0x0174 934 935 /* 936 * Multicast filter registers. 937 * MCAST0: Multicast filter register 0. 938 * MCAST1: Multicast filter register 1. 939 */ 940 #define MCAST0 0x0178 941 #define MCAST1 0x017c 942 943 /* 944 * UART registers. 945 * UARTCSR0: UART1 TX register. 946 * UARTCSR1: UART1 RX register. 947 * UARTCSR3: UART1 frame control register. 948 * UARTCSR4: UART1 buffer control register. 949 * UART2CSR0: UART2 TX register. 950 * UART2CSR1: UART2 RX register. 951 * UART2CSR3: UART2 frame control register. 952 * UART2CSR4: UART2 buffer control register. 953 */ 954 #define UARTCSR0 0x0180 955 #define UARTCSR1 0x0184 956 #define UARTCSR3 0x0188 957 #define UARTCSR4 0x018c 958 #define UART2CSR0 0x0190 959 #define UART2CSR1 0x0194 960 #define UART2CSR3 0x0198 961 #define UART2CSR4 0x019c 962 963 /* 964 * BBP registers. 965 * The wordsize of the BBP is 8 bits. 966 */ 967 968 /* 969 * R2: TX antenna control 970 */ 971 #define BBP_R2_TX_ANTENNA FIELD8(0x03) 972 #define BBP_R2_TX_IQ_FLIP FIELD8(0x04) 973 974 /* 975 * R14: RX antenna control 976 */ 977 #define BBP_R14_RX_ANTENNA FIELD8(0x03) 978 #define BBP_R14_RX_IQ_FLIP FIELD8(0x04) 979 980 /* 981 * BBP_R70 982 */ 983 #define BBP_R70_JAPAN_FILTER FIELD8(0x08) 984 985 /* 986 * RF registers 987 */ 988 989 /* 990 * RF 1 991 */ 992 #define RF1_TUNER FIELD32(0x00020000) 993 994 /* 995 * RF 3 996 */ 997 #define RF3_TUNER FIELD32(0x00000100) 998 #define RF3_TXPOWER FIELD32(0x00003e00) 999 1000 /* 1001 * EEPROM content. 1002 * The wordsize of the EEPROM is 16 bits. 1003 */ 1004 1005 /* 1006 * HW MAC address. 1007 */ 1008 #define EEPROM_MAC_ADDR_0 0x0002 1009 #define EEPROM_MAC_ADDR_BYTE0 FIELD16(0x00ff) 1010 #define EEPROM_MAC_ADDR_BYTE1 FIELD16(0xff00) 1011 #define EEPROM_MAC_ADDR1 0x0003 1012 #define EEPROM_MAC_ADDR_BYTE2 FIELD16(0x00ff) 1013 #define EEPROM_MAC_ADDR_BYTE3 FIELD16(0xff00) 1014 #define EEPROM_MAC_ADDR_2 0x0004 1015 #define EEPROM_MAC_ADDR_BYTE4 FIELD16(0x00ff) 1016 #define EEPROM_MAC_ADDR_BYTE5 FIELD16(0xff00) 1017 1018 /* 1019 * EEPROM antenna. 1020 * ANTENNA_NUM: Number of antenna's. 1021 * TX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. 1022 * RX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. 1023 * LED_MODE: 0: default, 1: TX/RX activity,2: Single (ignore link), 3: rsvd. 1024 * DYN_TXAGC: Dynamic TX AGC control. 1025 * HARDWARE_RADIO: 1: Hardware controlled radio. Read GPIO0. 1026 * RF_TYPE: Rf_type of this adapter. 1027 */ 1028 #define EEPROM_ANTENNA 0x10 1029 #define EEPROM_ANTENNA_NUM FIELD16(0x0003) 1030 #define EEPROM_ANTENNA_TX_DEFAULT FIELD16(0x000c) 1031 #define EEPROM_ANTENNA_RX_DEFAULT FIELD16(0x0030) 1032 #define EEPROM_ANTENNA_LED_MODE FIELD16(0x01c0) 1033 #define EEPROM_ANTENNA_DYN_TXAGC FIELD16(0x0200) 1034 #define EEPROM_ANTENNA_HARDWARE_RADIO FIELD16(0x0400) 1035 #define EEPROM_ANTENNA_RF_TYPE FIELD16(0xf800) 1036 1037 /* 1038 * EEPROM NIC config. 1039 * CARDBUS_ACCEL: 0: enable, 1: disable. 1040 * DYN_BBP_TUNE: 0: enable, 1: disable. 1041 * CCK_TX_POWER: CCK TX power compensation. 1042 */ 1043 #define EEPROM_NIC 0x11 1044 #define EEPROM_NIC_CARDBUS_ACCEL FIELD16(0x0001) 1045 #define EEPROM_NIC_DYN_BBP_TUNE FIELD16(0x0002) 1046 #define EEPROM_NIC_CCK_TX_POWER FIELD16(0x000c) 1047 1048 /* 1049 * EEPROM geography. 1050 * GEO: Default geography setting for device. 1051 */ 1052 #define EEPROM_GEOGRAPHY 0x12 1053 #define EEPROM_GEOGRAPHY_GEO FIELD16(0x0f00) 1054 1055 /* 1056 * EEPROM BBP. 1057 */ 1058 #define EEPROM_BBP_START 0x13 1059 #define EEPROM_BBP_SIZE 16 1060 #define EEPROM_BBP_VALUE FIELD16(0x00ff) 1061 #define EEPROM_BBP_REG_ID FIELD16(0xff00) 1062 1063 /* 1064 * EEPROM TXPOWER 1065 */ 1066 #define EEPROM_TXPOWER_START 0x23 1067 #define EEPROM_TXPOWER_SIZE 7 1068 #define EEPROM_TXPOWER_1 FIELD16(0x00ff) 1069 #define EEPROM_TXPOWER_2 FIELD16(0xff00) 1070 1071 /* 1072 * RSSI <-> dBm offset calibration 1073 */ 1074 #define EEPROM_CALIBRATE_OFFSET 0x3e 1075 #define EEPROM_CALIBRATE_OFFSET_RSSI FIELD16(0x00ff) 1076 1077 /* 1078 * DMA descriptor defines. 1079 */ 1080 #define TXD_DESC_SIZE (11 * sizeof(__le32)) 1081 #define RXD_DESC_SIZE (11 * sizeof(__le32)) 1082 1083 /* 1084 * TX descriptor format for TX, PRIO, ATIM and Beacon Ring. 1085 */ 1086 1087 /* 1088 * Word0 1089 */ 1090 #define TXD_W0_OWNER_NIC FIELD32(0x00000001) 1091 #define TXD_W0_VALID FIELD32(0x00000002) 1092 #define TXD_W0_RESULT FIELD32(0x0000001c) 1093 #define TXD_W0_RETRY_COUNT FIELD32(0x000000e0) 1094 #define TXD_W0_MORE_FRAG FIELD32(0x00000100) 1095 #define TXD_W0_ACK FIELD32(0x00000200) 1096 #define TXD_W0_TIMESTAMP FIELD32(0x00000400) 1097 #define TXD_W0_OFDM FIELD32(0x00000800) 1098 #define TXD_W0_CIPHER_OWNER FIELD32(0x00001000) 1099 #define TXD_W0_IFS FIELD32(0x00006000) 1100 #define TXD_W0_RETRY_MODE FIELD32(0x00008000) 1101 #define TXD_W0_DATABYTE_COUNT FIELD32(0x0fff0000) 1102 #define TXD_W0_CIPHER_ALG FIELD32(0xe0000000) 1103 1104 /* 1105 * Word1 1106 */ 1107 #define TXD_W1_BUFFER_ADDRESS FIELD32(0xffffffff) 1108 1109 /* 1110 * Word2 1111 */ 1112 #define TXD_W2_IV_OFFSET FIELD32(0x0000003f) 1113 #define TXD_W2_AIFS FIELD32(0x000000c0) 1114 #define TXD_W2_CWMIN FIELD32(0x00000f00) 1115 #define TXD_W2_CWMAX FIELD32(0x0000f000) 1116 1117 /* 1118 * Word3: PLCP information 1119 */ 1120 #define TXD_W3_PLCP_SIGNAL FIELD32(0x000000ff) 1121 #define TXD_W3_PLCP_SERVICE FIELD32(0x0000ff00) 1122 #define TXD_W3_PLCP_LENGTH_LOW FIELD32(0x00ff0000) 1123 #define TXD_W3_PLCP_LENGTH_HIGH FIELD32(0xff000000) 1124 1125 /* 1126 * Word4 1127 */ 1128 #define TXD_W4_IV FIELD32(0xffffffff) 1129 1130 /* 1131 * Word5 1132 */ 1133 #define TXD_W5_EIV FIELD32(0xffffffff) 1134 1135 /* 1136 * Word6-9: Key 1137 */ 1138 #define TXD_W6_KEY FIELD32(0xffffffff) 1139 #define TXD_W7_KEY FIELD32(0xffffffff) 1140 #define TXD_W8_KEY FIELD32(0xffffffff) 1141 #define TXD_W9_KEY FIELD32(0xffffffff) 1142 1143 /* 1144 * Word10 1145 */ 1146 #define TXD_W10_RTS FIELD32(0x00000001) 1147 #define TXD_W10_TX_RATE FIELD32(0x000000fe) 1148 1149 /* 1150 * RX descriptor format for RX Ring. 1151 */ 1152 1153 /* 1154 * Word0 1155 */ 1156 #define RXD_W0_OWNER_NIC FIELD32(0x00000001) 1157 #define RXD_W0_UNICAST_TO_ME FIELD32(0x00000002) 1158 #define RXD_W0_MULTICAST FIELD32(0x00000004) 1159 #define RXD_W0_BROADCAST FIELD32(0x00000008) 1160 #define RXD_W0_MY_BSS FIELD32(0x00000010) 1161 #define RXD_W0_CRC_ERROR FIELD32(0x00000020) 1162 #define RXD_W0_OFDM FIELD32(0x00000040) 1163 #define RXD_W0_PHYSICAL_ERROR FIELD32(0x00000080) 1164 #define RXD_W0_CIPHER_OWNER FIELD32(0x00000100) 1165 #define RXD_W0_ICV_ERROR FIELD32(0x00000200) 1166 #define RXD_W0_IV_OFFSET FIELD32(0x0000fc00) 1167 #define RXD_W0_DATABYTE_COUNT FIELD32(0x0fff0000) 1168 #define RXD_W0_CIPHER_ALG FIELD32(0xe0000000) 1169 1170 /* 1171 * Word1 1172 */ 1173 #define RXD_W1_BUFFER_ADDRESS FIELD32(0xffffffff) 1174 1175 /* 1176 * Word2 1177 */ 1178 #define RXD_W2_SIGNAL FIELD32(0x000000ff) 1179 #define RXD_W2_RSSI FIELD32(0x0000ff00) 1180 #define RXD_W2_TA FIELD32(0xffff0000) 1181 1182 /* 1183 * Word3 1184 */ 1185 #define RXD_W3_TA FIELD32(0xffffffff) 1186 1187 /* 1188 * Word4 1189 */ 1190 #define RXD_W4_IV FIELD32(0xffffffff) 1191 1192 /* 1193 * Word5 1194 */ 1195 #define RXD_W5_EIV FIELD32(0xffffffff) 1196 1197 /* 1198 * Word6-9: Key 1199 */ 1200 #define RXD_W6_KEY FIELD32(0xffffffff) 1201 #define RXD_W7_KEY FIELD32(0xffffffff) 1202 #define RXD_W8_KEY FIELD32(0xffffffff) 1203 #define RXD_W9_KEY FIELD32(0xffffffff) 1204 1205 /* 1206 * Word10 1207 */ 1208 #define RXD_W10_DROP FIELD32(0x00000001) 1209 1210 /* 1211 * Macros for converting txpower from EEPROM to mac80211 value 1212 * and from mac80211 value to register value. 1213 */ 1214 #define MIN_TXPOWER 0 1215 #define MAX_TXPOWER 31 1216 #define DEFAULT_TXPOWER 24 1217 1218 #define TXPOWER_FROM_DEV(__txpower) \ 1219 (((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) 1220 1221 #define TXPOWER_TO_DEV(__txpower) \ 1222 clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER) 1223 1224 #endif /* RT2500PCI_H */ 1225