1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * include/linux/mmc/sdio.h 4 * 5 * Copyright 2006-2007 Pierre Ossman 6 */ 7 8 #ifndef LINUX_MMC_SDIO_H 9 #define LINUX_MMC_SDIO_H 10 11 /* SDIO commands type argument response */ 12 #define SD_IO_SEND_OP_COND 5 /* bcr [23:0] OCR R4 */ 13 #define SD_IO_RW_DIRECT 52 /* ac [31:0] See below R5 */ 14 #define SD_IO_RW_EXTENDED 53 /* adtc [31:0] See below R5 */ 15 16 /* 17 * SD_IO_RW_DIRECT argument format: 18 * 19 * [31] R/W flag 20 * [30:28] Function number 21 * [27] RAW flag 22 * [25:9] Register address 23 * [7:0] Data 24 */ 25 26 /* 27 * SD_IO_RW_EXTENDED argument format: 28 * 29 * [31] R/W flag 30 * [30:28] Function number 31 * [27] Block mode 32 * [26] Increment address 33 * [25:9] Register address 34 * [8:0] Byte/block count 35 */ 36 37 #define R4_18V_PRESENT (1<<24) 38 #define R4_MEMORY_PRESENT (1 << 27) 39 40 /* 41 SDIO status in R5 42 Type 43 e : error bit 44 s : status bit 45 r : detected and set for the actual command response 46 x : detected and set during command execution. the host must poll 47 the card by sending status command in order to read these bits. 48 Clear condition 49 a : according to the card state 50 b : always related to the previous command. Reception of 51 a valid command will clear it (with a delay of one command) 52 c : clear by read 53 */ 54 55 #define R5_COM_CRC_ERROR (1 << 15) /* er, b */ 56 #define R5_ILLEGAL_COMMAND (1 << 14) /* er, b */ 57 #define R5_ERROR (1 << 11) /* erx, c */ 58 #define R5_FUNCTION_NUMBER (1 << 9) /* er, c */ 59 #define R5_OUT_OF_RANGE (1 << 8) /* er, c */ 60 #define R5_STATUS(x) (x & 0xCB00) 61 #define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */ 62 63 /* 64 * Card Common Control Registers (CCCR) 65 */ 66 67 #define SDIO_CCCR_CCCR 0x00 68 69 #define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */ 70 #define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */ 71 #define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */ 72 #define SDIO_CCCR_REV_3_00 3 /* CCCR/FBR Version 3.00 */ 73 74 #define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */ 75 #define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */ 76 #define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */ 77 #define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */ 78 #define SDIO_SDIO_REV_3_00 4 /* SDIO Spec Version 3.00 */ 79 80 #define SDIO_CCCR_SD 0x01 81 82 #define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */ 83 #define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */ 84 #define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */ 85 #define SDIO_SD_REV_3_00 3 /* SD Physical Spev Version 3.00 */ 86 87 #define SDIO_CCCR_IOEx 0x02 88 #define SDIO_CCCR_IORx 0x03 89 90 #define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */ 91 #define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */ 92 93 #define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */ 94 95 #define SDIO_CCCR_IF 0x07 /* bus interface controls */ 96 97 #define SDIO_BUS_WIDTH_MASK 0x03 /* data bus width setting */ 98 #define SDIO_BUS_WIDTH_1BIT 0x00 99 #define SDIO_BUS_WIDTH_RESERVED 0x01 100 #define SDIO_BUS_WIDTH_4BIT 0x02 101 #define SDIO_BUS_ECSI 0x20 /* Enable continuous SPI interrupt */ 102 #define SDIO_BUS_SCSI 0x40 /* Support continuous SPI interrupt */ 103 104 #define SDIO_BUS_ASYNC_INT 0x20 105 106 #define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */ 107 108 #define SDIO_CCCR_CAPS 0x08 109 110 #define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */ 111 #define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */ 112 #define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */ 113 #define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */ 114 #define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */ 115 #define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */ 116 #define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */ 117 #define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */ 118 119 #define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */ 120 121 /* Following 4 regs are valid only if SBS is set */ 122 #define SDIO_CCCR_SUSPEND 0x0c 123 #define SDIO_CCCR_SELx 0x0d 124 #define SDIO_CCCR_EXECx 0x0e 125 #define SDIO_CCCR_READYx 0x0f 126 127 #define SDIO_CCCR_BLKSIZE 0x10 128 129 #define SDIO_CCCR_POWER 0x12 130 131 #define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */ 132 #define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */ 133 134 #define SDIO_CCCR_SPEED 0x13 135 136 #define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */ 137 #define SDIO_SPEED_BSS_SHIFT 1 138 #define SDIO_SPEED_BSS_MASK (7<<SDIO_SPEED_BSS_SHIFT) 139 #define SDIO_SPEED_SDR12 (0<<SDIO_SPEED_BSS_SHIFT) 140 #define SDIO_SPEED_SDR25 (1<<SDIO_SPEED_BSS_SHIFT) 141 #define SDIO_SPEED_SDR50 (2<<SDIO_SPEED_BSS_SHIFT) 142 #define SDIO_SPEED_SDR104 (3<<SDIO_SPEED_BSS_SHIFT) 143 #define SDIO_SPEED_DDR50 (4<<SDIO_SPEED_BSS_SHIFT) 144 #define SDIO_SPEED_EHS SDIO_SPEED_SDR25 /* Enable High-Speed */ 145 146 #define SDIO_CCCR_UHS 0x14 147 #define SDIO_UHS_SDR50 0x01 148 #define SDIO_UHS_SDR104 0x02 149 #define SDIO_UHS_DDR50 0x04 150 151 #define SDIO_CCCR_DRIVE_STRENGTH 0x15 152 #define SDIO_SDTx_MASK 0x07 153 #define SDIO_DRIVE_SDTA (1<<0) 154 #define SDIO_DRIVE_SDTC (1<<1) 155 #define SDIO_DRIVE_SDTD (1<<2) 156 #define SDIO_DRIVE_DTSx_MASK 0x03 157 #define SDIO_DRIVE_DTSx_SHIFT 4 158 #define SDIO_DTSx_SET_TYPE_B (0 << SDIO_DRIVE_DTSx_SHIFT) 159 #define SDIO_DTSx_SET_TYPE_A (1 << SDIO_DRIVE_DTSx_SHIFT) 160 #define SDIO_DTSx_SET_TYPE_C (2 << SDIO_DRIVE_DTSx_SHIFT) 161 #define SDIO_DTSx_SET_TYPE_D (3 << SDIO_DRIVE_DTSx_SHIFT) 162 /* 163 * Function Basic Registers (FBR) 164 */ 165 166 #define SDIO_FBR_BASE(f) ((f) * 0x100) /* base of function f's FBRs */ 167 168 #define SDIO_FBR_STD_IF 0x00 169 170 #define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */ 171 #define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */ 172 173 #define SDIO_FBR_STD_IF_EXT 0x01 174 175 #define SDIO_FBR_POWER 0x02 176 177 #define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */ 178 #define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */ 179 180 #define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */ 181 182 183 #define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */ 184 185 #define SDIO_FBR_CSA_DATA 0x0F 186 187 #define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */ 188 189 #endif /* LINUX_MMC_SDIO_H */ 190