1 /* SPDX-License-Identifier: GPL-2.0 */
2
3 /*
4 * xHCI host controller driver
5 *
6 * Copyright (C) 2008 Intel Corp.
7 *
8 * Author: Sarah Sharp
9 * Some code borrowed from the Linux EHCI driver.
10 */
11
12 #ifndef __LINUX_XHCI_HCD_H
13 #define __LINUX_XHCI_HCD_H
14
15 #include <linux/usb.h>
16 #include <linux/timer.h>
17 #include <linux/kernel.h>
18 #include <linux/usb/hcd.h>
19 #include <linux/io-64-nonatomic-lo-hi.h>
20
21 /* Code sharing between pci-quirks and xhci hcd */
22 #include "xhci-ext-caps.h"
23 #include "pci-quirks.h"
24
25 /* max buffer size for trace and debug messages */
26 #define XHCI_MSG_MAX 500
27
28 /* xHCI PCI Configuration Registers */
29 #define XHCI_SBRN_OFFSET (0x60)
30
31 /* Max number of USB devices for any host controller - limit in section 6.1 */
32 #define MAX_HC_SLOTS 256
33 /* Section 5.3.3 - MaxPorts */
34 #define MAX_HC_PORTS 127
35
36 /*
37 * xHCI register interface.
38 * This corresponds to the eXtensible Host Controller Interface (xHCI)
39 * Revision 0.95 specification
40 */
41
42 /**
43 * struct xhci_cap_regs - xHCI Host Controller Capability Registers.
44 * @hc_capbase: length of the capabilities register and HC version number
45 * @hcs_params1: HCSPARAMS1 - Structural Parameters 1
46 * @hcs_params2: HCSPARAMS2 - Structural Parameters 2
47 * @hcs_params3: HCSPARAMS3 - Structural Parameters 3
48 * @hcc_params: HCCPARAMS - Capability Parameters
49 * @db_off: DBOFF - Doorbell array offset
50 * @run_regs_off: RTSOFF - Runtime register space offset
51 * @hcc_params2: HCCPARAMS2 Capability Parameters 2, xhci 1.1 only
52 */
53 struct xhci_cap_regs {
54 __le32 hc_capbase;
55 __le32 hcs_params1;
56 __le32 hcs_params2;
57 __le32 hcs_params3;
58 __le32 hcc_params;
59 __le32 db_off;
60 __le32 run_regs_off;
61 __le32 hcc_params2; /* xhci 1.1 */
62 /* Reserved up to (CAPLENGTH - 0x1C) */
63 };
64
65 /* hc_capbase bitmasks */
66 /* bits 7:0 - how long is the Capabilities register */
67 #define HC_LENGTH(p) XHCI_HC_LENGTH(p)
68 /* bits 31:16 */
69 #define HC_VERSION(p) (((p) >> 16) & 0xffff)
70
71 /* HCSPARAMS1 - hcs_params1 - bitmasks */
72 /* bits 0:7, Max Device Slots */
73 #define HCS_MAX_SLOTS(p) (((p) >> 0) & 0xff)
74 #define HCS_SLOTS_MASK 0xff
75 /* bits 8:18, Max Interrupters */
76 #define HCS_MAX_INTRS(p) (((p) >> 8) & 0x7ff)
77 /* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
78 #define HCS_MAX_PORTS(p) (((p) >> 24) & 0x7f)
79
80 /* HCSPARAMS2 - hcs_params2 - bitmasks */
81 /* bits 0:3, frames or uframes that SW needs to queue transactions
82 * ahead of the HW to meet periodic deadlines */
83 #define HCS_IST(p) (((p) >> 0) & 0xf)
84 /* bits 4:7, max number of Event Ring segments */
85 #define HCS_ERST_MAX(p) (((p) >> 4) & 0xf)
86 /* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
87 /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
88 /* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
89 #define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
90
91 /* HCSPARAMS3 - hcs_params3 - bitmasks */
92 /* bits 0:7, Max U1 to U0 latency for the roothub ports */
93 #define HCS_U1_LATENCY(p) (((p) >> 0) & 0xff)
94 /* bits 16:31, Max U2 to U0 latency for the roothub ports */
95 #define HCS_U2_LATENCY(p) (((p) >> 16) & 0xffff)
96
97 /* HCCPARAMS - hcc_params - bitmasks */
98 /* true: HC can use 64-bit address pointers */
99 #define HCC_64BIT_ADDR(p) ((p) & (1 << 0))
100 /* true: HC can do bandwidth negotiation */
101 #define HCC_BANDWIDTH_NEG(p) ((p) & (1 << 1))
102 /* true: HC uses 64-byte Device Context structures
103 * FIXME 64-byte context structures aren't supported yet.
104 */
105 #define HCC_64BYTE_CONTEXT(p) ((p) & (1 << 2))
106 /* true: HC has port power switches */
107 #define HCC_PPC(p) ((p) & (1 << 3))
108 /* true: HC has port indicators */
109 #define HCS_INDICATOR(p) ((p) & (1 << 4))
110 /* true: HC has Light HC Reset Capability */
111 #define HCC_LIGHT_RESET(p) ((p) & (1 << 5))
112 /* true: HC supports latency tolerance messaging */
113 #define HCC_LTC(p) ((p) & (1 << 6))
114 /* true: no secondary Stream ID Support */
115 #define HCC_NSS(p) ((p) & (1 << 7))
116 /* true: HC supports Stopped - Short Packet */
117 #define HCC_SPC(p) ((p) & (1 << 9))
118 /* true: HC has Contiguous Frame ID Capability */
119 #define HCC_CFC(p) ((p) & (1 << 11))
120 /* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
121 #define HCC_MAX_PSA(p) (1 << ((((p) >> 12) & 0xf) + 1))
122 /* Extended Capabilities pointer from PCI base - section 5.3.6 */
123 #define HCC_EXT_CAPS(p) XHCI_HCC_EXT_CAPS(p)
124
125 #define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
126
127 /* db_off bitmask - bits 0:1 reserved */
128 #define DBOFF_MASK (~0x3)
129
130 /* run_regs_off bitmask - bits 0:4 reserved */
131 #define RTSOFF_MASK (~0x1f)
132
133 /* HCCPARAMS2 - hcc_params2 - bitmasks */
134 /* true: HC supports U3 entry Capability */
135 #define HCC2_U3C(p) ((p) & (1 << 0))
136 /* true: HC supports Configure endpoint command Max exit latency too large */
137 #define HCC2_CMC(p) ((p) & (1 << 1))
138 /* true: HC supports Force Save context Capability */
139 #define HCC2_FSC(p) ((p) & (1 << 2))
140 /* true: HC supports Compliance Transition Capability */
141 #define HCC2_CTC(p) ((p) & (1 << 3))
142 /* true: HC support Large ESIT payload Capability > 48k */
143 #define HCC2_LEC(p) ((p) & (1 << 4))
144 /* true: HC support Configuration Information Capability */
145 #define HCC2_CIC(p) ((p) & (1 << 5))
146 /* true: HC support Extended TBC Capability, Isoc burst count > 65535 */
147 #define HCC2_ETC(p) ((p) & (1 << 6))
148
149 /* Number of registers per port */
150 #define NUM_PORT_REGS 4
151
152 #define PORTSC 0
153 #define PORTPMSC 1
154 #define PORTLI 2
155 #define PORTHLPMC 3
156
157 /**
158 * struct xhci_op_regs - xHCI Host Controller Operational Registers.
159 * @command: USBCMD - xHC command register
160 * @status: USBSTS - xHC status register
161 * @page_size: This indicates the page size that the host controller
162 * supports. If bit n is set, the HC supports a page size
163 * of 2^(n+12), up to a 128MB page size.
164 * 4K is the minimum page size.
165 * @cmd_ring: CRP - 64-bit Command Ring Pointer
166 * @dcbaa_ptr: DCBAAP - 64-bit Device Context Base Address Array Pointer
167 * @config_reg: CONFIG - Configure Register
168 * @port_status_base: PORTSCn - base address for Port Status and Control
169 * Each port has a Port Status and Control register,
170 * followed by a Port Power Management Status and Control
171 * register, a Port Link Info register, and a reserved
172 * register.
173 * @port_power_base: PORTPMSCn - base address for
174 * Port Power Management Status and Control
175 * @port_link_base: PORTLIn - base address for Port Link Info (current
176 * Link PM state and control) for USB 2.1 and USB 3.0
177 * devices.
178 */
179 struct xhci_op_regs {
180 __le32 command;
181 __le32 status;
182 __le32 page_size;
183 __le32 reserved1;
184 __le32 reserved2;
185 __le32 dev_notification;
186 __le64 cmd_ring;
187 /* rsvd: offset 0x20-2F */
188 __le32 reserved3[4];
189 __le64 dcbaa_ptr;
190 __le32 config_reg;
191 /* rsvd: offset 0x3C-3FF */
192 __le32 reserved4[241];
193 /* port 1 registers, which serve as a base address for other ports */
194 __le32 port_status_base;
195 __le32 port_power_base;
196 __le32 port_link_base;
197 __le32 reserved5;
198 /* registers for ports 2-255 */
199 __le32 reserved6[NUM_PORT_REGS*254];
200 };
201
202 /* USBCMD - USB command - command bitmasks */
203 /* start/stop HC execution - do not write unless HC is halted*/
204 #define CMD_RUN XHCI_CMD_RUN
205 /* Reset HC - resets internal HC state machine and all registers (except
206 * PCI config regs). HC does NOT drive a USB reset on the downstream ports.
207 * The xHCI driver must reinitialize the xHC after setting this bit.
208 */
209 #define CMD_RESET (1 << 1)
210 /* Event Interrupt Enable - a '1' allows interrupts from the host controller */
211 #define CMD_EIE XHCI_CMD_EIE
212 /* Host System Error Interrupt Enable - get out-of-band signal for HC errors */
213 #define CMD_HSEIE XHCI_CMD_HSEIE
214 /* bits 4:6 are reserved (and should be preserved on writes). */
215 /* light reset (port status stays unchanged) - reset completed when this is 0 */
216 #define CMD_LRESET (1 << 7)
217 /* host controller save/restore state. */
218 #define CMD_CSS (1 << 8)
219 #define CMD_CRS (1 << 9)
220 /* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
221 #define CMD_EWE XHCI_CMD_EWE
222 /* MFINDEX power management - '1' means xHC can stop MFINDEX counter if all root
223 * hubs are in U3 (selective suspend), disconnect, disabled, or powered-off.
224 * '0' means the xHC can power it off if all ports are in the disconnect,
225 * disabled, or powered-off state.
226 */
227 #define CMD_PM_INDEX (1 << 11)
228 /* bit 14 Extended TBC Enable, changes Isoc TRB fields to support larger TBC */
229 #define CMD_ETE (1 << 14)
230 /* bits 15:31 are reserved (and should be preserved on writes). */
231
232 #define XHCI_RESET_LONG_USEC (10 * 1000 * 1000)
233 #define XHCI_RESET_SHORT_USEC (250 * 1000)
234
235 /* IMAN - Interrupt Management Register */
236 #define IMAN_IE (1 << 1)
237 #define IMAN_IP (1 << 0)
238
239 /* USBSTS - USB status - status bitmasks */
240 /* HC not running - set to 1 when run/stop bit is cleared. */
241 #define STS_HALT XHCI_STS_HALT
242 /* serious error, e.g. PCI parity error. The HC will clear the run/stop bit. */
243 #define STS_FATAL (1 << 2)
244 /* event interrupt - clear this prior to clearing any IP flags in IR set*/
245 #define STS_EINT (1 << 3)
246 /* port change detect */
247 #define STS_PORT (1 << 4)
248 /* bits 5:7 reserved and zeroed */
249 /* save state status - '1' means xHC is saving state */
250 #define STS_SAVE (1 << 8)
251 /* restore state status - '1' means xHC is restoring state */
252 #define STS_RESTORE (1 << 9)
253 /* true: save or restore error */
254 #define STS_SRE (1 << 10)
255 /* true: Controller Not Ready to accept doorbell or op reg writes after reset */
256 #define STS_CNR XHCI_STS_CNR
257 /* true: internal Host Controller Error - SW needs to reset and reinitialize */
258 #define STS_HCE (1 << 12)
259 /* bits 13:31 reserved and should be preserved */
260
261 /*
262 * DNCTRL - Device Notification Control Register - dev_notification bitmasks
263 * Generate a device notification event when the HC sees a transaction with a
264 * notification type that matches a bit set in this bit field.
265 */
266 #define DEV_NOTE_MASK (0xffff)
267 #define ENABLE_DEV_NOTE(x) (1 << (x))
268 /* Most of the device notification types should only be used for debug.
269 * SW does need to pay attention to function wake notifications.
270 */
271 #define DEV_NOTE_FWAKE ENABLE_DEV_NOTE(1)
272
273 /* CRCR - Command Ring Control Register - cmd_ring bitmasks */
274 /* bit 0 is the command ring cycle state */
275 /* stop ring operation after completion of the currently executing command */
276 #define CMD_RING_PAUSE (1 << 1)
277 /* stop ring immediately - abort the currently executing command */
278 #define CMD_RING_ABORT (1 << 2)
279 /* true: command ring is running */
280 #define CMD_RING_RUNNING (1 << 3)
281 /* bits 4:5 reserved and should be preserved */
282 /* Command Ring pointer - bit mask for the lower 32 bits. */
283 #define CMD_RING_RSVD_BITS (0x3f)
284
285 /* CONFIG - Configure Register - config_reg bitmasks */
286 /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
287 #define MAX_DEVS(p) ((p) & 0xff)
288 /* bit 8: U3 Entry Enabled, assert PLC when root port enters U3, xhci 1.1 */
289 #define CONFIG_U3E (1 << 8)
290 /* bit 9: Configuration Information Enable, xhci 1.1 */
291 #define CONFIG_CIE (1 << 9)
292 /* bits 10:31 - reserved and should be preserved */
293
294 /* PORTSC - Port Status and Control Register - port_status_base bitmasks */
295 /* true: device connected */
296 #define PORT_CONNECT (1 << 0)
297 /* true: port enabled */
298 #define PORT_PE (1 << 1)
299 /* bit 2 reserved and zeroed */
300 /* true: port has an over-current condition */
301 #define PORT_OC (1 << 3)
302 /* true: port reset signaling asserted */
303 #define PORT_RESET (1 << 4)
304 /* Port Link State - bits 5:8
305 * A read gives the current link PM state of the port,
306 * a write with Link State Write Strobe set sets the link state.
307 */
308 #define PORT_PLS_MASK (0xf << 5)
309 #define XDEV_U0 (0x0 << 5)
310 #define XDEV_U1 (0x1 << 5)
311 #define XDEV_U2 (0x2 << 5)
312 #define XDEV_U3 (0x3 << 5)
313 #define XDEV_DISABLED (0x4 << 5)
314 #define XDEV_RXDETECT (0x5 << 5)
315 #define XDEV_INACTIVE (0x6 << 5)
316 #define XDEV_POLLING (0x7 << 5)
317 #define XDEV_RECOVERY (0x8 << 5)
318 #define XDEV_HOT_RESET (0x9 << 5)
319 #define XDEV_COMP_MODE (0xa << 5)
320 #define XDEV_TEST_MODE (0xb << 5)
321 #define XDEV_RESUME (0xf << 5)
322
323 /* true: port has power (see HCC_PPC) */
324 #define PORT_POWER (1 << 9)
325 /* bits 10:13 indicate device speed:
326 * 0 - undefined speed - port hasn't be initialized by a reset yet
327 * 1 - full speed
328 * 2 - low speed
329 * 3 - high speed
330 * 4 - super speed
331 * 5-15 reserved
332 */
333 #define DEV_SPEED_MASK (0xf << 10)
334 #define XDEV_FS (0x1 << 10)
335 #define XDEV_LS (0x2 << 10)
336 #define XDEV_HS (0x3 << 10)
337 #define XDEV_SS (0x4 << 10)
338 #define XDEV_SSP (0x5 << 10)
339 #define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
340 #define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
341 #define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
342 #define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
343 #define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
344 #define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
345 #define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
346 #define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
347
348 /* Bits 20:23 in the Slot Context are the speed for the device */
349 #define SLOT_SPEED_FS (XDEV_FS << 10)
350 #define SLOT_SPEED_LS (XDEV_LS << 10)
351 #define SLOT_SPEED_HS (XDEV_HS << 10)
352 #define SLOT_SPEED_SS (XDEV_SS << 10)
353 #define SLOT_SPEED_SSP (XDEV_SSP << 10)
354 /* Port Indicator Control */
355 #define PORT_LED_OFF (0 << 14)
356 #define PORT_LED_AMBER (1 << 14)
357 #define PORT_LED_GREEN (2 << 14)
358 #define PORT_LED_MASK (3 << 14)
359 /* Port Link State Write Strobe - set this when changing link state */
360 #define PORT_LINK_STROBE (1 << 16)
361 /* true: connect status change */
362 #define PORT_CSC (1 << 17)
363 /* true: port enable change */
364 #define PORT_PEC (1 << 18)
365 /* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
366 * into an enabled state, and the device into the default state. A "warm" reset
367 * also resets the link, forcing the device through the link training sequence.
368 * SW can also look at the Port Reset register to see when warm reset is done.
369 */
370 #define PORT_WRC (1 << 19)
371 /* true: over-current change */
372 #define PORT_OCC (1 << 20)
373 /* true: reset change - 1 to 0 transition of PORT_RESET */
374 #define PORT_RC (1 << 21)
375 /* port link status change - set on some port link state transitions:
376 * Transition Reason
377 * ------------------------------------------------------------------------------
378 * - U3 to Resume Wakeup signaling from a device
379 * - Resume to Recovery to U0 USB 3.0 device resume
380 * - Resume to U0 USB 2.0 device resume
381 * - U3 to Recovery to U0 Software resume of USB 3.0 device complete
382 * - U3 to U0 Software resume of USB 2.0 device complete
383 * - U2 to U0 L1 resume of USB 2.1 device complete
384 * - U0 to U0 (???) L1 entry rejection by USB 2.1 device
385 * - U0 to disabled L1 entry error with USB 2.1 device
386 * - Any state to inactive Error on USB 3.0 port
387 */
388 #define PORT_PLC (1 << 22)
389 /* port configure error change - port failed to configure its link partner */
390 #define PORT_CEC (1 << 23)
391 #define PORT_CHANGE_MASK (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
392 PORT_RC | PORT_PLC | PORT_CEC)
393
394
395 /* Cold Attach Status - xHC can set this bit to report device attached during
396 * Sx state. Warm port reset should be perfomed to clear this bit and move port
397 * to connected state.
398 */
399 #define PORT_CAS (1 << 24)
400 /* wake on connect (enable) */
401 #define PORT_WKCONN_E (1 << 25)
402 /* wake on disconnect (enable) */
403 #define PORT_WKDISC_E (1 << 26)
404 /* wake on over-current (enable) */
405 #define PORT_WKOC_E (1 << 27)
406 /* bits 28:29 reserved */
407 /* true: device is non-removable - for USB 3.0 roothub emulation */
408 #define PORT_DEV_REMOVE (1 << 30)
409 /* Initiate a warm port reset - complete when PORT_WRC is '1' */
410 #define PORT_WR (1 << 31)
411
412 /* We mark duplicate entries with -1 */
413 #define DUPLICATE_ENTRY ((u8)(-1))
414
415 /* Port Power Management Status and Control - port_power_base bitmasks */
416 /* Inactivity timer value for transitions into U1, in microseconds.
417 * Timeout can be up to 127us. 0xFF means an infinite timeout.
418 */
419 #define PORT_U1_TIMEOUT(p) ((p) & 0xff)
420 #define PORT_U1_TIMEOUT_MASK 0xff
421 /* Inactivity timer value for transitions into U2 */
422 #define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
423 #define PORT_U2_TIMEOUT_MASK (0xff << 8)
424 /* Bits 24:31 for port testing */
425
426 /* USB2 Protocol PORTSPMSC */
427 #define PORT_L1S_MASK 7
428 #define PORT_L1S_SUCCESS 1
429 #define PORT_RWE (1 << 3)
430 #define PORT_HIRD(p) (((p) & 0xf) << 4)
431 #define PORT_HIRD_MASK (0xf << 4)
432 #define PORT_L1DS_MASK (0xff << 8)
433 #define PORT_L1DS(p) (((p) & 0xff) << 8)
434 #define PORT_HLE (1 << 16)
435 #define PORT_TEST_MODE_SHIFT 28
436
437 /* USB3 Protocol PORTLI Port Link Information */
438 #define PORT_RX_LANES(p) (((p) >> 16) & 0xf)
439 #define PORT_TX_LANES(p) (((p) >> 20) & 0xf)
440
441 /* USB2 Protocol PORTHLPMC */
442 #define PORT_HIRDM(p)((p) & 3)
443 #define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
444 #define PORT_BESLD(p)(((p) & 0xf) << 10)
445
446 /* use 512 microseconds as USB2 LPM L1 default timeout. */
447 #define XHCI_L1_TIMEOUT 512
448
449 /* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
450 * Safe to use with mixed HIRD and BESL systems (host and device) and is used
451 * by other operating systems.
452 *
453 * XHCI 1.0 errata 8/14/12 Table 13 notes:
454 * "Software should choose xHC BESL/BESLD field values that do not violate a
455 * device's resume latency requirements,
456 * e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
457 * or not program values < '4' if BLC = '0' and a BESL device is attached.
458 */
459 #define XHCI_DEFAULT_BESL 4
460
461 /*
462 * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
463 * to complete link training. usually link trainig completes much faster
464 * so check status 10 times with 36ms sleep in places we need to wait for
465 * polling to complete.
466 */
467 #define XHCI_PORT_POLLING_LFPS_TIME 36
468
469 /**
470 * struct xhci_intr_reg - Interrupt Register Set
471 * @irq_pending: IMAN - Interrupt Management Register. Used to enable
472 * interrupts and check for pending interrupts.
473 * @irq_control: IMOD - Interrupt Moderation Register.
474 * Used to throttle interrupts.
475 * @erst_size: Number of segments in the Event Ring Segment Table (ERST).
476 * @erst_base: ERST base address.
477 * @erst_dequeue: Event ring dequeue pointer.
478 *
479 * Each interrupter (defined by a MSI-X vector) has an event ring and an Event
480 * Ring Segment Table (ERST) associated with it. The event ring is comprised of
481 * multiple segments of the same size. The HC places events on the ring and
482 * "updates the Cycle bit in the TRBs to indicate to software the current
483 * position of the Enqueue Pointer." The HCD (Linux) processes those events and
484 * updates the dequeue pointer.
485 */
486 struct xhci_intr_reg {
487 __le32 irq_pending;
488 __le32 irq_control;
489 __le32 erst_size;
490 __le32 rsvd;
491 __le64 erst_base;
492 __le64 erst_dequeue;
493 };
494
495 /* irq_pending bitmasks */
496 #define ER_IRQ_PENDING(p) ((p) & 0x1)
497 /* bits 2:31 need to be preserved */
498 /* THIS IS BUGGY - FIXME - IP IS WRITE 1 TO CLEAR */
499 #define ER_IRQ_CLEAR(p) ((p) & 0xfffffffe)
500 #define ER_IRQ_ENABLE(p) ((ER_IRQ_CLEAR(p)) | 0x2)
501 #define ER_IRQ_DISABLE(p) ((ER_IRQ_CLEAR(p)) & ~(0x2))
502
503 /* irq_control bitmasks */
504 /* Minimum interval between interrupts (in 250ns intervals). The interval
505 * between interrupts will be longer if there are no events on the event ring.
506 * Default is 4000 (1 ms).
507 */
508 #define ER_IRQ_INTERVAL_MASK (0xffff)
509 /* Counter used to count down the time to the next interrupt - HW use only */
510 #define ER_IRQ_COUNTER_MASK (0xffff << 16)
511
512 /* erst_size bitmasks */
513 /* Preserve bits 16:31 of erst_size */
514 #define ERST_SIZE_MASK (0xffff << 16)
515
516 /* erst_dequeue bitmasks */
517 /* Dequeue ERST Segment Index (DESI) - Segment number (or alias)
518 * where the current dequeue pointer lies. This is an optional HW hint.
519 */
520 #define ERST_DESI_MASK (0x7)
521 /* Event Handler Busy (EHB) - is the event ring scheduled to be serviced by
522 * a work queue (or delayed service routine)?
523 */
524 #define ERST_EHB (1 << 3)
525 #define ERST_PTR_MASK (0xf)
526
527 /**
528 * struct xhci_run_regs
529 * @microframe_index:
530 * MFINDEX - current microframe number
531 *
532 * Section 5.5 Host Controller Runtime Registers:
533 * "Software should read and write these registers using only Dword (32 bit)
534 * or larger accesses"
535 */
536 struct xhci_run_regs {
537 __le32 microframe_index;
538 __le32 rsvd[7];
539 struct xhci_intr_reg ir_set[128];
540 };
541
542 /**
543 * struct doorbell_array
544 *
545 * Bits 0 - 7: Endpoint target
546 * Bits 8 - 15: RsvdZ
547 * Bits 16 - 31: Stream ID
548 *
549 * Section 5.6
550 */
551 struct xhci_doorbell_array {
552 __le32 doorbell[256];
553 };
554
555 #define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16))
556 #define DB_VALUE_HOST 0x00000000
557
558 /**
559 * struct xhci_protocol_caps
560 * @revision: major revision, minor revision, capability ID,
561 * and next capability pointer.
562 * @name_string: Four ASCII characters to say which spec this xHC
563 * follows, typically "USB ".
564 * @port_info: Port offset, count, and protocol-defined information.
565 */
566 struct xhci_protocol_caps {
567 u32 revision;
568 u32 name_string;
569 u32 port_info;
570 };
571
572 #define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff)
573 #define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff)
574 #define XHCI_EXT_PORT_PSIC(x) (((x) >> 28) & 0x0f)
575 #define XHCI_EXT_PORT_OFF(x) ((x) & 0xff)
576 #define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff)
577
578 #define XHCI_EXT_PORT_PSIV(x) (((x) >> 0) & 0x0f)
579 #define XHCI_EXT_PORT_PSIE(x) (((x) >> 4) & 0x03)
580 #define XHCI_EXT_PORT_PLT(x) (((x) >> 6) & 0x03)
581 #define XHCI_EXT_PORT_PFD(x) (((x) >> 8) & 0x01)
582 #define XHCI_EXT_PORT_LP(x) (((x) >> 14) & 0x03)
583 #define XHCI_EXT_PORT_PSIM(x) (((x) >> 16) & 0xffff)
584
585 #define PLT_MASK (0x03 << 6)
586 #define PLT_SYM (0x00 << 6)
587 #define PLT_ASYM_RX (0x02 << 6)
588 #define PLT_ASYM_TX (0x03 << 6)
589
590 /**
591 * struct xhci_container_ctx
592 * @type: Type of context. Used to calculated offsets to contained contexts.
593 * @size: Size of the context data
594 * @bytes: The raw context data given to HW
595 * @dma: dma address of the bytes
596 *
597 * Represents either a Device or Input context. Holds a pointer to the raw
598 * memory used for the context (bytes) and dma address of it (dma).
599 */
600 struct xhci_container_ctx {
601 unsigned type;
602 #define XHCI_CTX_TYPE_DEVICE 0x1
603 #define XHCI_CTX_TYPE_INPUT 0x2
604
605 int size;
606
607 u8 *bytes;
608 dma_addr_t dma;
609 };
610
611 /**
612 * struct xhci_slot_ctx
613 * @dev_info: Route string, device speed, hub info, and last valid endpoint
614 * @dev_info2: Max exit latency for device number, root hub port number
615 * @tt_info: tt_info is used to construct split transaction tokens
616 * @dev_state: slot state and device address
617 *
618 * Slot Context - section 6.2.1.1. This assumes the HC uses 32-byte context
619 * structures. If the HC uses 64-byte contexts, there is an additional 32 bytes
620 * reserved at the end of the slot context for HC internal use.
621 */
622 struct xhci_slot_ctx {
623 __le32 dev_info;
624 __le32 dev_info2;
625 __le32 tt_info;
626 __le32 dev_state;
627 /* offset 0x10 to 0x1f reserved for HC internal use */
628 __le32 reserved[4];
629 };
630
631 /* dev_info bitmasks */
632 /* Route String - 0:19 */
633 #define ROUTE_STRING_MASK (0xfffff)
634 /* Device speed - values defined by PORTSC Device Speed field - 20:23 */
635 #define DEV_SPEED (0xf << 20)
636 #define GET_DEV_SPEED(n) (((n) & DEV_SPEED) >> 20)
637 /* bit 24 reserved */
638 /* Is this LS/FS device connected through a HS hub? - bit 25 */
639 #define DEV_MTT (0x1 << 25)
640 /* Set if the device is a hub - bit 26 */
641 #define DEV_HUB (0x1 << 26)
642 /* Index of the last valid endpoint context in this device context - 27:31 */
643 #define LAST_CTX_MASK (0x1f << 27)
644 #define LAST_CTX(p) ((p) << 27)
645 #define LAST_CTX_TO_EP_NUM(p) (((p) >> 27) - 1)
646 #define SLOT_FLAG (1 << 0)
647 #define EP0_FLAG (1 << 1)
648
649 /* dev_info2 bitmasks */
650 /* Max Exit Latency (ms) - worst case time to wake up all links in dev path */
651 #define MAX_EXIT (0xffff)
652 /* Root hub port number that is needed to access the USB device */
653 #define ROOT_HUB_PORT(p) (((p) & 0xff) << 16)
654 #define DEVINFO_TO_ROOT_HUB_PORT(p) (((p) >> 16) & 0xff)
655 /* Maximum number of ports under a hub device */
656 #define XHCI_MAX_PORTS(p) (((p) & 0xff) << 24)
657 #define DEVINFO_TO_MAX_PORTS(p) (((p) & (0xff << 24)) >> 24)
658
659 /* tt_info bitmasks */
660 /*
661 * TT Hub Slot ID - for low or full speed devices attached to a high-speed hub
662 * The Slot ID of the hub that isolates the high speed signaling from
663 * this low or full-speed device. '0' if attached to root hub port.
664 */
665 #define TT_SLOT (0xff)
666 /*
667 * The number of the downstream facing port of the high-speed hub
668 * '0' if the device is not low or full speed.
669 */
670 #define TT_PORT (0xff << 8)
671 #define TT_THINK_TIME(p) (((p) & 0x3) << 16)
672 #define GET_TT_THINK_TIME(p) (((p) & (0x3 << 16)) >> 16)
673
674 /* dev_state bitmasks */
675 /* USB device address - assigned by the HC */
676 #define DEV_ADDR_MASK (0xff)
677 /* bits 8:26 reserved */
678 /* Slot state */
679 #define SLOT_STATE (0x1f << 27)
680 #define GET_SLOT_STATE(p) (((p) & (0x1f << 27)) >> 27)
681
682 #define SLOT_STATE_DISABLED 0
683 #define SLOT_STATE_ENABLED SLOT_STATE_DISABLED
684 #define SLOT_STATE_DEFAULT 1
685 #define SLOT_STATE_ADDRESSED 2
686 #define SLOT_STATE_CONFIGURED 3
687
688 /**
689 * struct xhci_ep_ctx
690 * @ep_info: endpoint state, streams, mult, and interval information.
691 * @ep_info2: information on endpoint type, max packet size, max burst size,
692 * error count, and whether the HC will force an event for all
693 * transactions.
694 * @deq: 64-bit ring dequeue pointer address. If the endpoint only
695 * defines one stream, this points to the endpoint transfer ring.
696 * Otherwise, it points to a stream context array, which has a
697 * ring pointer for each flow.
698 * @tx_info:
699 * Average TRB lengths for the endpoint ring and
700 * max payload within an Endpoint Service Interval Time (ESIT).
701 *
702 * Endpoint Context - section 6.2.1.2. This assumes the HC uses 32-byte context
703 * structures. If the HC uses 64-byte contexts, there is an additional 32 bytes
704 * reserved at the end of the endpoint context for HC internal use.
705 */
706 struct xhci_ep_ctx {
707 __le32 ep_info;
708 __le32 ep_info2;
709 __le64 deq;
710 __le32 tx_info;
711 /* offset 0x14 - 0x1f reserved for HC internal use */
712 __le32 reserved[3];
713 };
714
715 /* ep_info bitmasks */
716 /*
717 * Endpoint State - bits 0:2
718 * 0 - disabled
719 * 1 - running
720 * 2 - halted due to halt condition - ok to manipulate endpoint ring
721 * 3 - stopped
722 * 4 - TRB error
723 * 5-7 - reserved
724 */
725 #define EP_STATE_MASK (0x7)
726 #define EP_STATE_DISABLED 0
727 #define EP_STATE_RUNNING 1
728 #define EP_STATE_HALTED 2
729 #define EP_STATE_STOPPED 3
730 #define EP_STATE_ERROR 4
731 #define GET_EP_CTX_STATE(ctx) (le32_to_cpu((ctx)->ep_info) & EP_STATE_MASK)
732
733 /* Mult - Max number of burtst within an interval, in EP companion desc. */
734 #define EP_MULT(p) (((p) & 0x3) << 8)
735 #define CTX_TO_EP_MULT(p) (((p) >> 8) & 0x3)
736 /* bits 10:14 are Max Primary Streams */
737 /* bit 15 is Linear Stream Array */
738 /* Interval - period between requests to an endpoint - 125u increments. */
739 #define EP_INTERVAL(p) (((p) & 0xff) << 16)
740 #define EP_INTERVAL_TO_UFRAMES(p) (1 << (((p) >> 16) & 0xff))
741 #define CTX_TO_EP_INTERVAL(p) (((p) >> 16) & 0xff)
742 #define EP_MAXPSTREAMS_MASK (0x1f << 10)
743 #define EP_MAXPSTREAMS(p) (((p) << 10) & EP_MAXPSTREAMS_MASK)
744 #define CTX_TO_EP_MAXPSTREAMS(p) (((p) & EP_MAXPSTREAMS_MASK) >> 10)
745 /* Endpoint is set up with a Linear Stream Array (vs. Secondary Stream Array) */
746 #define EP_HAS_LSA (1 << 15)
747 /* hosts with LEC=1 use bits 31:24 as ESIT high bits. */
748 #define CTX_TO_MAX_ESIT_PAYLOAD_HI(p) (((p) >> 24) & 0xff)
749
750 /* ep_info2 bitmasks */
751 /*
752 * Force Event - generate transfer events for all TRBs for this endpoint
753 * This will tell the HC to ignore the IOC and ISP flags (for debugging only).
754 */
755 #define FORCE_EVENT (0x1)
756 #define ERROR_COUNT(p) (((p) & 0x3) << 1)
757 #define CTX_TO_EP_TYPE(p) (((p) >> 3) & 0x7)
758 #define EP_TYPE(p) ((p) << 3)
759 #define ISOC_OUT_EP 1
760 #define BULK_OUT_EP 2
761 #define INT_OUT_EP 3
762 #define CTRL_EP 4
763 #define ISOC_IN_EP 5
764 #define BULK_IN_EP 6
765 #define INT_IN_EP 7
766 /* bit 6 reserved */
767 /* bit 7 is Host Initiate Disable - for disabling stream selection */
768 #define MAX_BURST(p) (((p)&0xff) << 8)
769 #define CTX_TO_MAX_BURST(p) (((p) >> 8) & 0xff)
770 #define MAX_PACKET(p) (((p)&0xffff) << 16)
771 #define MAX_PACKET_MASK (0xffff << 16)
772 #define MAX_PACKET_DECODED(p) (((p) >> 16) & 0xffff)
773
774 /* tx_info bitmasks */
775 #define EP_AVG_TRB_LENGTH(p) ((p) & 0xffff)
776 #define EP_MAX_ESIT_PAYLOAD_LO(p) (((p) & 0xffff) << 16)
777 #define EP_MAX_ESIT_PAYLOAD_HI(p) ((((p) >> 16) & 0xff) << 24)
778 #define CTX_TO_MAX_ESIT_PAYLOAD(p) (((p) >> 16) & 0xffff)
779
780 /* deq bitmasks */
781 #define EP_CTX_CYCLE_MASK (1 << 0)
782 #define SCTX_DEQ_MASK (~0xfL)
783
784
785 /**
786 * struct xhci_input_control_context
787 * Input control context; see section 6.2.5.
788 *
789 * @drop_context: set the bit of the endpoint context you want to disable
790 * @add_context: set the bit of the endpoint context you want to enable
791 */
792 struct xhci_input_control_ctx {
793 __le32 drop_flags;
794 __le32 add_flags;
795 __le32 rsvd2[6];
796 };
797
798 #define EP_IS_ADDED(ctrl_ctx, i) \
799 (le32_to_cpu(ctrl_ctx->add_flags) & (1 << (i + 1)))
800 #define EP_IS_DROPPED(ctrl_ctx, i) \
801 (le32_to_cpu(ctrl_ctx->drop_flags) & (1 << (i + 1)))
802
803 /* Represents everything that is needed to issue a command on the command ring.
804 * It's useful to pre-allocate these for commands that cannot fail due to
805 * out-of-memory errors, like freeing streams.
806 */
807 struct xhci_command {
808 /* Input context for changing device state */
809 struct xhci_container_ctx *in_ctx;
810 u32 status;
811 int slot_id;
812 /* If completion is null, no one is waiting on this command
813 * and the structure can be freed after the command completes.
814 */
815 struct completion *completion;
816 union xhci_trb *command_trb;
817 struct list_head cmd_list;
818 };
819
820 /* drop context bitmasks */
821 #define DROP_EP(x) (0x1 << x)
822 /* add context bitmasks */
823 #define ADD_EP(x) (0x1 << x)
824
825 struct xhci_stream_ctx {
826 /* 64-bit stream ring address, cycle state, and stream type */
827 __le64 stream_ring;
828 /* offset 0x14 - 0x1f reserved for HC internal use */
829 __le32 reserved[2];
830 };
831
832 /* Stream Context Types (section 6.4.1) - bits 3:1 of stream ctx deq ptr */
833 #define SCT_FOR_CTX(p) (((p) & 0x7) << 1)
834 /* Secondary stream array type, dequeue pointer is to a transfer ring */
835 #define SCT_SEC_TR 0
836 /* Primary stream array type, dequeue pointer is to a transfer ring */
837 #define SCT_PRI_TR 1
838 /* Dequeue pointer is for a secondary stream array (SSA) with 8 entries */
839 #define SCT_SSA_8 2
840 #define SCT_SSA_16 3
841 #define SCT_SSA_32 4
842 #define SCT_SSA_64 5
843 #define SCT_SSA_128 6
844 #define SCT_SSA_256 7
845
846 /* Assume no secondary streams for now */
847 struct xhci_stream_info {
848 struct xhci_ring **stream_rings;
849 /* Number of streams, including stream 0 (which drivers can't use) */
850 unsigned int num_streams;
851 /* The stream context array may be bigger than
852 * the number of streams the driver asked for
853 */
854 struct xhci_stream_ctx *stream_ctx_array;
855 unsigned int num_stream_ctxs;
856 dma_addr_t ctx_array_dma;
857 /* For mapping physical TRB addresses to segments in stream rings */
858 struct radix_tree_root trb_address_map;
859 struct xhci_command *free_streams_command;
860 };
861
862 #define SMALL_STREAM_ARRAY_SIZE 256
863 #define MEDIUM_STREAM_ARRAY_SIZE 1024
864
865 /* Some Intel xHCI host controllers need software to keep track of the bus
866 * bandwidth. Keep track of endpoint info here. Each root port is allocated
867 * the full bus bandwidth. We must also treat TTs (including each port under a
868 * multi-TT hub) as a separate bandwidth domain. The direct memory interface
869 * (DMI) also limits the total bandwidth (across all domains) that can be used.
870 */
871 struct xhci_bw_info {
872 /* ep_interval is zero-based */
873 unsigned int ep_interval;
874 /* mult and num_packets are one-based */
875 unsigned int mult;
876 unsigned int num_packets;
877 unsigned int max_packet_size;
878 unsigned int max_esit_payload;
879 unsigned int type;
880 };
881
882 /* "Block" sizes in bytes the hardware uses for different device speeds.
883 * The logic in this part of the hardware limits the number of bits the hardware
884 * can use, so must represent bandwidth in a less precise manner to mimic what
885 * the scheduler hardware computes.
886 */
887 #define FS_BLOCK 1
888 #define HS_BLOCK 4
889 #define SS_BLOCK 16
890 #define DMI_BLOCK 32
891
892 /* Each device speed has a protocol overhead (CRC, bit stuffing, etc) associated
893 * with each byte transferred. SuperSpeed devices have an initial overhead to
894 * set up bursts. These are in blocks, see above. LS overhead has already been
895 * translated into FS blocks.
896 */
897 #define DMI_OVERHEAD 8
898 #define DMI_OVERHEAD_BURST 4
899 #define SS_OVERHEAD 8
900 #define SS_OVERHEAD_BURST 32
901 #define HS_OVERHEAD 26
902 #define FS_OVERHEAD 20
903 #define LS_OVERHEAD 128
904 /* The TTs need to claim roughly twice as much bandwidth (94 bytes per
905 * microframe ~= 24Mbps) of the HS bus as the devices can actually use because
906 * of overhead associated with split transfers crossing microframe boundaries.
907 * 31 blocks is pure protocol overhead.
908 */
909 #define TT_HS_OVERHEAD (31 + 94)
910 #define TT_DMI_OVERHEAD (25 + 12)
911
912 /* Bandwidth limits in blocks */
913 #define FS_BW_LIMIT 1285
914 #define TT_BW_LIMIT 1320
915 #define HS_BW_LIMIT 1607
916 #define SS_BW_LIMIT_IN 3906
917 #define DMI_BW_LIMIT_IN 3906
918 #define SS_BW_LIMIT_OUT 3906
919 #define DMI_BW_LIMIT_OUT 3906
920
921 /* Percentage of bus bandwidth reserved for non-periodic transfers */
922 #define FS_BW_RESERVED 10
923 #define HS_BW_RESERVED 20
924 #define SS_BW_RESERVED 10
925
926 struct xhci_virt_ep {
927 struct xhci_virt_device *vdev; /* parent */
928 unsigned int ep_index;
929 struct xhci_ring *ring;
930 /* Related to endpoints that are configured to use stream IDs only */
931 struct xhci_stream_info *stream_info;
932 /* Temporary storage in case the configure endpoint command fails and we
933 * have to restore the device state to the previous state
934 */
935 struct xhci_ring *new_ring;
936 unsigned int err_count;
937 unsigned int ep_state;
938 #define SET_DEQ_PENDING (1 << 0)
939 #define EP_HALTED (1 << 1) /* For stall handling */
940 #define EP_STOP_CMD_PENDING (1 << 2) /* For URB cancellation */
941 /* Transitioning the endpoint to using streams, don't enqueue URBs */
942 #define EP_GETTING_STREAMS (1 << 3)
943 #define EP_HAS_STREAMS (1 << 4)
944 /* Transitioning the endpoint to not using streams, don't enqueue URBs */
945 #define EP_GETTING_NO_STREAMS (1 << 5)
946 #define EP_HARD_CLEAR_TOGGLE (1 << 6)
947 #define EP_SOFT_CLEAR_TOGGLE (1 << 7)
948 /* usb_hub_clear_tt_buffer is in progress */
949 #define EP_CLEARING_TT (1 << 8)
950 /* ---- Related to URB cancellation ---- */
951 struct list_head cancelled_td_list;
952 /* Watchdog timer for stop endpoint command to cancel URBs */
953 struct timer_list stop_cmd_timer;
954 struct xhci_hcd *xhci;
955 /* Dequeue pointer and dequeue segment for a submitted Set TR Dequeue
956 * command. We'll need to update the ring's dequeue segment and dequeue
957 * pointer after the command completes.
958 */
959 struct xhci_segment *queued_deq_seg;
960 union xhci_trb *queued_deq_ptr;
961 /*
962 * Sometimes the xHC can not process isochronous endpoint ring quickly
963 * enough, and it will miss some isoc tds on the ring and generate
964 * a Missed Service Error Event.
965 * Set skip flag when receive a Missed Service Error Event and
966 * process the missed tds on the endpoint ring.
967 */
968 bool skip;
969 /* Bandwidth checking storage */
970 struct xhci_bw_info bw_info;
971 struct list_head bw_endpoint_list;
972 /* Isoch Frame ID checking storage */
973 int next_frame_id;
974 /* Use new Isoch TRB layout needed for extended TBC support */
975 bool use_extended_tbc;
976 };
977
978 enum xhci_overhead_type {
979 LS_OVERHEAD_TYPE = 0,
980 FS_OVERHEAD_TYPE,
981 HS_OVERHEAD_TYPE,
982 };
983
984 struct xhci_interval_bw {
985 unsigned int num_packets;
986 /* Sorted by max packet size.
987 * Head of the list is the greatest max packet size.
988 */
989 struct list_head endpoints;
990 /* How many endpoints of each speed are present. */
991 unsigned int overhead[3];
992 };
993
994 #define XHCI_MAX_INTERVAL 16
995
996 struct xhci_interval_bw_table {
997 unsigned int interval0_esit_payload;
998 struct xhci_interval_bw interval_bw[XHCI_MAX_INTERVAL];
999 /* Includes reserved bandwidth for async endpoints */
1000 unsigned int bw_used;
1001 unsigned int ss_bw_in;
1002 unsigned int ss_bw_out;
1003 };
1004
1005 #define EP_CTX_PER_DEV 31
1006
1007 struct xhci_virt_device {
1008 int slot_id;
1009 struct usb_device *udev;
1010 /*
1011 * Commands to the hardware are passed an "input context" that
1012 * tells the hardware what to change in its data structures.
1013 * The hardware will return changes in an "output context" that
1014 * software must allocate for the hardware. We need to keep
1015 * track of input and output contexts separately because
1016 * these commands might fail and we don't trust the hardware.
1017 */
1018 struct xhci_container_ctx *out_ctx;
1019 /* Used for addressing devices and configuration changes */
1020 struct xhci_container_ctx *in_ctx;
1021 struct xhci_virt_ep eps[EP_CTX_PER_DEV];
1022 u8 fake_port;
1023 u8 real_port;
1024 struct xhci_interval_bw_table *bw_table;
1025 struct xhci_tt_bw_info *tt_info;
1026 /*
1027 * flags for state tracking based on events and issued commands.
1028 * Software can not rely on states from output contexts because of
1029 * latency between events and xHC updating output context values.
1030 * See xhci 1.1 section 4.8.3 for more details
1031 */
1032 unsigned long flags;
1033 #define VDEV_PORT_ERROR BIT(0) /* Port error, link inactive */
1034
1035 /* The current max exit latency for the enabled USB3 link states. */
1036 u16 current_mel;
1037 /* Used for the debugfs interfaces. */
1038 void *debugfs_private;
1039 };
1040
1041 /*
1042 * For each roothub, keep track of the bandwidth information for each periodic
1043 * interval.
1044 *
1045 * If a high speed hub is attached to the roothub, each TT associated with that
1046 * hub is a separate bandwidth domain. The interval information for the
1047 * endpoints on the devices under that TT will appear in the TT structure.
1048 */
1049 struct xhci_root_port_bw_info {
1050 struct list_head tts;
1051 unsigned int num_active_tts;
1052 struct xhci_interval_bw_table bw_table;
1053 };
1054
1055 struct xhci_tt_bw_info {
1056 struct list_head tt_list;
1057 int slot_id;
1058 int ttport;
1059 struct xhci_interval_bw_table bw_table;
1060 int active_eps;
1061 };
1062
1063
1064 /**
1065 * struct xhci_device_context_array
1066 * @dev_context_ptr array of 64-bit DMA addresses for device contexts
1067 */
1068 struct xhci_device_context_array {
1069 /* 64-bit device addresses; we only write 32-bit addresses */
1070 __le64 dev_context_ptrs[MAX_HC_SLOTS];
1071 /* private xHCD pointers */
1072 dma_addr_t dma;
1073 };
1074 /* TODO: write function to set the 64-bit device DMA address */
1075 /*
1076 * TODO: change this to be dynamically sized at HC mem init time since the HC
1077 * might not be able to handle the maximum number of devices possible.
1078 */
1079
1080
1081 struct xhci_transfer_event {
1082 /* 64-bit buffer address, or immediate data */
1083 __le64 buffer;
1084 __le32 transfer_len;
1085 /* This field is interpreted differently based on the type of TRB */
1086 __le32 flags;
1087 };
1088
1089 /* Transfer event TRB length bit mask */
1090 /* bits 0:23 */
1091 #define EVENT_TRB_LEN(p) ((p) & 0xffffff)
1092
1093 /** Transfer Event bit fields **/
1094 #define TRB_TO_EP_ID(p) (((p) >> 16) & 0x1f)
1095
1096 /* Completion Code - only applicable for some types of TRBs */
1097 #define COMP_CODE_MASK (0xff << 24)
1098 #define GET_COMP_CODE(p) (((p) & COMP_CODE_MASK) >> 24)
1099 #define COMP_INVALID 0
1100 #define COMP_SUCCESS 1
1101 #define COMP_DATA_BUFFER_ERROR 2
1102 #define COMP_BABBLE_DETECTED_ERROR 3
1103 #define COMP_USB_TRANSACTION_ERROR 4
1104 #define COMP_TRB_ERROR 5
1105 #define COMP_STALL_ERROR 6
1106 #define COMP_RESOURCE_ERROR 7
1107 #define COMP_BANDWIDTH_ERROR 8
1108 #define COMP_NO_SLOTS_AVAILABLE_ERROR 9
1109 #define COMP_INVALID_STREAM_TYPE_ERROR 10
1110 #define COMP_SLOT_NOT_ENABLED_ERROR 11
1111 #define COMP_ENDPOINT_NOT_ENABLED_ERROR 12
1112 #define COMP_SHORT_PACKET 13
1113 #define COMP_RING_UNDERRUN 14
1114 #define COMP_RING_OVERRUN 15
1115 #define COMP_VF_EVENT_RING_FULL_ERROR 16
1116 #define COMP_PARAMETER_ERROR 17
1117 #define COMP_BANDWIDTH_OVERRUN_ERROR 18
1118 #define COMP_CONTEXT_STATE_ERROR 19
1119 #define COMP_NO_PING_RESPONSE_ERROR 20
1120 #define COMP_EVENT_RING_FULL_ERROR 21
1121 #define COMP_INCOMPATIBLE_DEVICE_ERROR 22
1122 #define COMP_MISSED_SERVICE_ERROR 23
1123 #define COMP_COMMAND_RING_STOPPED 24
1124 #define COMP_COMMAND_ABORTED 25
1125 #define COMP_STOPPED 26
1126 #define COMP_STOPPED_LENGTH_INVALID 27
1127 #define COMP_STOPPED_SHORT_PACKET 28
1128 #define COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR 29
1129 #define COMP_ISOCH_BUFFER_OVERRUN 31
1130 #define COMP_EVENT_LOST_ERROR 32
1131 #define COMP_UNDEFINED_ERROR 33
1132 #define COMP_INVALID_STREAM_ID_ERROR 34
1133 #define COMP_SECONDARY_BANDWIDTH_ERROR 35
1134 #define COMP_SPLIT_TRANSACTION_ERROR 36
1135
xhci_trb_comp_code_string(u8 status)1136 static inline const char *xhci_trb_comp_code_string(u8 status)
1137 {
1138 switch (status) {
1139 case COMP_INVALID:
1140 return "Invalid";
1141 case COMP_SUCCESS:
1142 return "Success";
1143 case COMP_DATA_BUFFER_ERROR:
1144 return "Data Buffer Error";
1145 case COMP_BABBLE_DETECTED_ERROR:
1146 return "Babble Detected";
1147 case COMP_USB_TRANSACTION_ERROR:
1148 return "USB Transaction Error";
1149 case COMP_TRB_ERROR:
1150 return "TRB Error";
1151 case COMP_STALL_ERROR:
1152 return "Stall Error";
1153 case COMP_RESOURCE_ERROR:
1154 return "Resource Error";
1155 case COMP_BANDWIDTH_ERROR:
1156 return "Bandwidth Error";
1157 case COMP_NO_SLOTS_AVAILABLE_ERROR:
1158 return "No Slots Available Error";
1159 case COMP_INVALID_STREAM_TYPE_ERROR:
1160 return "Invalid Stream Type Error";
1161 case COMP_SLOT_NOT_ENABLED_ERROR:
1162 return "Slot Not Enabled Error";
1163 case COMP_ENDPOINT_NOT_ENABLED_ERROR:
1164 return "Endpoint Not Enabled Error";
1165 case COMP_SHORT_PACKET:
1166 return "Short Packet";
1167 case COMP_RING_UNDERRUN:
1168 return "Ring Underrun";
1169 case COMP_RING_OVERRUN:
1170 return "Ring Overrun";
1171 case COMP_VF_EVENT_RING_FULL_ERROR:
1172 return "VF Event Ring Full Error";
1173 case COMP_PARAMETER_ERROR:
1174 return "Parameter Error";
1175 case COMP_BANDWIDTH_OVERRUN_ERROR:
1176 return "Bandwidth Overrun Error";
1177 case COMP_CONTEXT_STATE_ERROR:
1178 return "Context State Error";
1179 case COMP_NO_PING_RESPONSE_ERROR:
1180 return "No Ping Response Error";
1181 case COMP_EVENT_RING_FULL_ERROR:
1182 return "Event Ring Full Error";
1183 case COMP_INCOMPATIBLE_DEVICE_ERROR:
1184 return "Incompatible Device Error";
1185 case COMP_MISSED_SERVICE_ERROR:
1186 return "Missed Service Error";
1187 case COMP_COMMAND_RING_STOPPED:
1188 return "Command Ring Stopped";
1189 case COMP_COMMAND_ABORTED:
1190 return "Command Aborted";
1191 case COMP_STOPPED:
1192 return "Stopped";
1193 case COMP_STOPPED_LENGTH_INVALID:
1194 return "Stopped - Length Invalid";
1195 case COMP_STOPPED_SHORT_PACKET:
1196 return "Stopped - Short Packet";
1197 case COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR:
1198 return "Max Exit Latency Too Large Error";
1199 case COMP_ISOCH_BUFFER_OVERRUN:
1200 return "Isoch Buffer Overrun";
1201 case COMP_EVENT_LOST_ERROR:
1202 return "Event Lost Error";
1203 case COMP_UNDEFINED_ERROR:
1204 return "Undefined Error";
1205 case COMP_INVALID_STREAM_ID_ERROR:
1206 return "Invalid Stream ID Error";
1207 case COMP_SECONDARY_BANDWIDTH_ERROR:
1208 return "Secondary Bandwidth Error";
1209 case COMP_SPLIT_TRANSACTION_ERROR:
1210 return "Split Transaction Error";
1211 default:
1212 return "Unknown!!";
1213 }
1214 }
1215
1216 struct xhci_link_trb {
1217 /* 64-bit segment pointer*/
1218 __le64 segment_ptr;
1219 __le32 intr_target;
1220 __le32 control;
1221 };
1222
1223 /* control bitfields */
1224 #define LINK_TOGGLE (0x1<<1)
1225
1226 /* Command completion event TRB */
1227 struct xhci_event_cmd {
1228 /* Pointer to command TRB, or the value passed by the event data trb */
1229 __le64 cmd_trb;
1230 __le32 status;
1231 __le32 flags;
1232 };
1233
1234 /* flags bitmasks */
1235
1236 /* Address device - disable SetAddress */
1237 #define TRB_BSR (1<<9)
1238
1239 /* Configure Endpoint - Deconfigure */
1240 #define TRB_DC (1<<9)
1241
1242 /* Stop Ring - Transfer State Preserve */
1243 #define TRB_TSP (1<<9)
1244
1245 enum xhci_ep_reset_type {
1246 EP_HARD_RESET,
1247 EP_SOFT_RESET,
1248 };
1249
1250 /* Force Event */
1251 #define TRB_TO_VF_INTR_TARGET(p) (((p) & (0x3ff << 22)) >> 22)
1252 #define TRB_TO_VF_ID(p) (((p) & (0xff << 16)) >> 16)
1253
1254 /* Set Latency Tolerance Value */
1255 #define TRB_TO_BELT(p) (((p) & (0xfff << 16)) >> 16)
1256
1257 /* Get Port Bandwidth */
1258 #define TRB_TO_DEV_SPEED(p) (((p) & (0xf << 16)) >> 16)
1259
1260 /* Force Header */
1261 #define TRB_TO_PACKET_TYPE(p) ((p) & 0x1f)
1262 #define TRB_TO_ROOTHUB_PORT(p) (((p) & (0xff << 24)) >> 24)
1263
1264 enum xhci_setup_dev {
1265 SETUP_CONTEXT_ONLY,
1266 SETUP_CONTEXT_ADDRESS,
1267 };
1268
1269 /* bits 16:23 are the virtual function ID */
1270 /* bits 24:31 are the slot ID */
1271 #define TRB_TO_SLOT_ID(p) (((p) & (0xff<<24)) >> 24)
1272 #define SLOT_ID_FOR_TRB(p) (((p) & 0xff) << 24)
1273
1274 /* Stop Endpoint TRB - ep_index to endpoint ID for this TRB */
1275 #define TRB_TO_EP_INDEX(p) ((((p) & (0x1f << 16)) >> 16) - 1)
1276 #define EP_ID_FOR_TRB(p) ((((p) + 1) & 0x1f) << 16)
1277
1278 #define SUSPEND_PORT_FOR_TRB(p) (((p) & 1) << 23)
1279 #define TRB_TO_SUSPEND_PORT(p) (((p) & (1 << 23)) >> 23)
1280 #define LAST_EP_INDEX 30
1281
1282 /* Set TR Dequeue Pointer command TRB fields, 6.4.3.9 */
1283 #define TRB_TO_STREAM_ID(p) ((((p) & (0xffff << 16)) >> 16))
1284 #define STREAM_ID_FOR_TRB(p) ((((p)) & 0xffff) << 16)
1285 #define SCT_FOR_TRB(p) (((p) << 1) & 0x7)
1286
1287 /* Link TRB specific fields */
1288 #define TRB_TC (1<<1)
1289
1290 /* Port Status Change Event TRB fields */
1291 /* Port ID - bits 31:24 */
1292 #define GET_PORT_ID(p) (((p) & (0xff << 24)) >> 24)
1293
1294 #define EVENT_DATA (1 << 2)
1295
1296 /* Normal TRB fields */
1297 /* transfer_len bitmasks - bits 0:16 */
1298 #define TRB_LEN(p) ((p) & 0x1ffff)
1299 /* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
1300 #define TRB_TD_SIZE(p) (min((p), (u32)31) << 17)
1301 #define GET_TD_SIZE(p) (((p) & 0x3e0000) >> 17)
1302 /* xhci 1.1 uses the TD_SIZE field for TBC if Extended TBC is enabled (ETE) */
1303 #define TRB_TD_SIZE_TBC(p) (min((p), (u32)31) << 17)
1304 /* Interrupter Target - which MSI-X vector to target the completion event at */
1305 #define TRB_INTR_TARGET(p) (((p) & 0x3ff) << 22)
1306 #define GET_INTR_TARGET(p) (((p) >> 22) & 0x3ff)
1307 /* Total burst count field, Rsvdz on xhci 1.1 with Extended TBC enabled (ETE) */
1308 #define TRB_TBC(p) (((p) & 0x3) << 7)
1309 #define TRB_TLBPC(p) (((p) & 0xf) << 16)
1310
1311 /* Cycle bit - indicates TRB ownership by HC or HCD */
1312 #define TRB_CYCLE (1<<0)
1313 /*
1314 * Force next event data TRB to be evaluated before task switch.
1315 * Used to pass OS data back after a TD completes.
1316 */
1317 #define TRB_ENT (1<<1)
1318 /* Interrupt on short packet */
1319 #define TRB_ISP (1<<2)
1320 /* Set PCIe no snoop attribute */
1321 #define TRB_NO_SNOOP (1<<3)
1322 /* Chain multiple TRBs into a TD */
1323 #define TRB_CHAIN (1<<4)
1324 /* Interrupt on completion */
1325 #define TRB_IOC (1<<5)
1326 /* The buffer pointer contains immediate data */
1327 #define TRB_IDT (1<<6)
1328 /* TDs smaller than this might use IDT */
1329 #define TRB_IDT_MAX_SIZE 8
1330
1331 /* Block Event Interrupt */
1332 #define TRB_BEI (1<<9)
1333
1334 /* Control transfer TRB specific fields */
1335 #define TRB_DIR_IN (1<<16)
1336 #define TRB_TX_TYPE(p) ((p) << 16)
1337 #define TRB_DATA_OUT 2
1338 #define TRB_DATA_IN 3
1339
1340 /* Isochronous TRB specific fields */
1341 #define TRB_SIA (1<<31)
1342 #define TRB_FRAME_ID(p) (((p) & 0x7ff) << 20)
1343
1344 struct xhci_generic_trb {
1345 __le32 field[4];
1346 };
1347
1348 union xhci_trb {
1349 struct xhci_link_trb link;
1350 struct xhci_transfer_event trans_event;
1351 struct xhci_event_cmd event_cmd;
1352 struct xhci_generic_trb generic;
1353 };
1354
1355 /* TRB bit mask */
1356 #define TRB_TYPE_BITMASK (0xfc00)
1357 #define TRB_TYPE(p) ((p) << 10)
1358 #define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
1359 /* TRB type IDs */
1360 /* bulk, interrupt, isoc scatter/gather, and control data stage */
1361 #define TRB_NORMAL 1
1362 /* setup stage for control transfers */
1363 #define TRB_SETUP 2
1364 /* data stage for control transfers */
1365 #define TRB_DATA 3
1366 /* status stage for control transfers */
1367 #define TRB_STATUS 4
1368 /* isoc transfers */
1369 #define TRB_ISOC 5
1370 /* TRB for linking ring segments */
1371 #define TRB_LINK 6
1372 #define TRB_EVENT_DATA 7
1373 /* Transfer Ring No-op (not for the command ring) */
1374 #define TRB_TR_NOOP 8
1375 /* Command TRBs */
1376 /* Enable Slot Command */
1377 #define TRB_ENABLE_SLOT 9
1378 /* Disable Slot Command */
1379 #define TRB_DISABLE_SLOT 10
1380 /* Address Device Command */
1381 #define TRB_ADDR_DEV 11
1382 /* Configure Endpoint Command */
1383 #define TRB_CONFIG_EP 12
1384 /* Evaluate Context Command */
1385 #define TRB_EVAL_CONTEXT 13
1386 /* Reset Endpoint Command */
1387 #define TRB_RESET_EP 14
1388 /* Stop Transfer Ring Command */
1389 #define TRB_STOP_RING 15
1390 /* Set Transfer Ring Dequeue Pointer Command */
1391 #define TRB_SET_DEQ 16
1392 /* Reset Device Command */
1393 #define TRB_RESET_DEV 17
1394 /* Force Event Command (opt) */
1395 #define TRB_FORCE_EVENT 18
1396 /* Negotiate Bandwidth Command (opt) */
1397 #define TRB_NEG_BANDWIDTH 19
1398 /* Set Latency Tolerance Value Command (opt) */
1399 #define TRB_SET_LT 20
1400 /* Get port bandwidth Command */
1401 #define TRB_GET_BW 21
1402 /* Force Header Command - generate a transaction or link management packet */
1403 #define TRB_FORCE_HEADER 22
1404 /* No-op Command - not for transfer rings */
1405 #define TRB_CMD_NOOP 23
1406 /* TRB IDs 24-31 reserved */
1407 /* Event TRBS */
1408 /* Transfer Event */
1409 #define TRB_TRANSFER 32
1410 /* Command Completion Event */
1411 #define TRB_COMPLETION 33
1412 /* Port Status Change Event */
1413 #define TRB_PORT_STATUS 34
1414 /* Bandwidth Request Event (opt) */
1415 #define TRB_BANDWIDTH_EVENT 35
1416 /* Doorbell Event (opt) */
1417 #define TRB_DOORBELL 36
1418 /* Host Controller Event */
1419 #define TRB_HC_EVENT 37
1420 /* Device Notification Event - device sent function wake notification */
1421 #define TRB_DEV_NOTE 38
1422 /* MFINDEX Wrap Event - microframe counter wrapped */
1423 #define TRB_MFINDEX_WRAP 39
1424 /* TRB IDs 40-47 reserved, 48-63 is vendor-defined */
1425
1426 /* Nec vendor-specific command completion event. */
1427 #define TRB_NEC_CMD_COMP 48
1428 /* Get NEC firmware revision. */
1429 #define TRB_NEC_GET_FW 49
1430
xhci_trb_type_string(u8 type)1431 static inline const char *xhci_trb_type_string(u8 type)
1432 {
1433 switch (type) {
1434 case TRB_NORMAL:
1435 return "Normal";
1436 case TRB_SETUP:
1437 return "Setup Stage";
1438 case TRB_DATA:
1439 return "Data Stage";
1440 case TRB_STATUS:
1441 return "Status Stage";
1442 case TRB_ISOC:
1443 return "Isoch";
1444 case TRB_LINK:
1445 return "Link";
1446 case TRB_EVENT_DATA:
1447 return "Event Data";
1448 case TRB_TR_NOOP:
1449 return "No-Op";
1450 case TRB_ENABLE_SLOT:
1451 return "Enable Slot Command";
1452 case TRB_DISABLE_SLOT:
1453 return "Disable Slot Command";
1454 case TRB_ADDR_DEV:
1455 return "Address Device Command";
1456 case TRB_CONFIG_EP:
1457 return "Configure Endpoint Command";
1458 case TRB_EVAL_CONTEXT:
1459 return "Evaluate Context Command";
1460 case TRB_RESET_EP:
1461 return "Reset Endpoint Command";
1462 case TRB_STOP_RING:
1463 return "Stop Ring Command";
1464 case TRB_SET_DEQ:
1465 return "Set TR Dequeue Pointer Command";
1466 case TRB_RESET_DEV:
1467 return "Reset Device Command";
1468 case TRB_FORCE_EVENT:
1469 return "Force Event Command";
1470 case TRB_NEG_BANDWIDTH:
1471 return "Negotiate Bandwidth Command";
1472 case TRB_SET_LT:
1473 return "Set Latency Tolerance Value Command";
1474 case TRB_GET_BW:
1475 return "Get Port Bandwidth Command";
1476 case TRB_FORCE_HEADER:
1477 return "Force Header Command";
1478 case TRB_CMD_NOOP:
1479 return "No-Op Command";
1480 case TRB_TRANSFER:
1481 return "Transfer Event";
1482 case TRB_COMPLETION:
1483 return "Command Completion Event";
1484 case TRB_PORT_STATUS:
1485 return "Port Status Change Event";
1486 case TRB_BANDWIDTH_EVENT:
1487 return "Bandwidth Request Event";
1488 case TRB_DOORBELL:
1489 return "Doorbell Event";
1490 case TRB_HC_EVENT:
1491 return "Host Controller Event";
1492 case TRB_DEV_NOTE:
1493 return "Device Notification Event";
1494 case TRB_MFINDEX_WRAP:
1495 return "MFINDEX Wrap Event";
1496 case TRB_NEC_CMD_COMP:
1497 return "NEC Command Completion Event";
1498 case TRB_NEC_GET_FW:
1499 return "NET Get Firmware Revision Command";
1500 default:
1501 return "UNKNOWN";
1502 }
1503 }
1504
1505 #define TRB_TYPE_LINK(x) (((x) & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK))
1506 /* Above, but for __le32 types -- can avoid work by swapping constants: */
1507 #define TRB_TYPE_LINK_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
1508 cpu_to_le32(TRB_TYPE(TRB_LINK)))
1509 #define TRB_TYPE_NOOP_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
1510 cpu_to_le32(TRB_TYPE(TRB_TR_NOOP)))
1511
1512 #define NEC_FW_MINOR(p) (((p) >> 0) & 0xff)
1513 #define NEC_FW_MAJOR(p) (((p) >> 8) & 0xff)
1514
1515 /*
1516 * TRBS_PER_SEGMENT must be a multiple of 4,
1517 * since the command ring is 64-byte aligned.
1518 * It must also be greater than 16.
1519 */
1520 #define TRBS_PER_SEGMENT 256
1521 /* Allow two commands + a link TRB, along with any reserved command TRBs */
1522 #define MAX_RSVD_CMD_TRBS (TRBS_PER_SEGMENT - 3)
1523 #define TRB_SEGMENT_SIZE (TRBS_PER_SEGMENT*16)
1524 #define TRB_SEGMENT_SHIFT (ilog2(TRB_SEGMENT_SIZE))
1525 /* TRB buffer pointers can't cross 64KB boundaries */
1526 #define TRB_MAX_BUFF_SHIFT 16
1527 #define TRB_MAX_BUFF_SIZE (1 << TRB_MAX_BUFF_SHIFT)
1528 /* How much data is left before the 64KB boundary? */
1529 #define TRB_BUFF_LEN_UP_TO_BOUNDARY(addr) (TRB_MAX_BUFF_SIZE - \
1530 (addr & (TRB_MAX_BUFF_SIZE - 1)))
1531 #define MAX_SOFT_RETRY 3
1532
1533 struct xhci_segment {
1534 union xhci_trb *trbs;
1535 /* private to HCD */
1536 struct xhci_segment *next;
1537 dma_addr_t dma;
1538 /* Max packet sized bounce buffer for td-fragmant alignment */
1539 dma_addr_t bounce_dma;
1540 void *bounce_buf;
1541 unsigned int bounce_offs;
1542 unsigned int bounce_len;
1543 };
1544
1545 struct xhci_td {
1546 struct list_head td_list;
1547 struct list_head cancelled_td_list;
1548 int status;
1549 struct urb *urb;
1550 struct xhci_segment *start_seg;
1551 union xhci_trb *first_trb;
1552 union xhci_trb *last_trb;
1553 struct xhci_segment *bounce_seg;
1554 /* actual_length of the URB has already been set */
1555 bool urb_length_set;
1556 };
1557
1558 /* xHCI command default timeout value */
1559 #define XHCI_CMD_DEFAULT_TIMEOUT (5 * HZ)
1560
1561 /* command descriptor */
1562 struct xhci_cd {
1563 struct xhci_command *command;
1564 union xhci_trb *cmd_trb;
1565 };
1566
1567 struct xhci_dequeue_state {
1568 struct xhci_segment *new_deq_seg;
1569 union xhci_trb *new_deq_ptr;
1570 int new_cycle_state;
1571 unsigned int stream_id;
1572 };
1573
1574 enum xhci_ring_type {
1575 TYPE_CTRL = 0,
1576 TYPE_ISOC,
1577 TYPE_BULK,
1578 TYPE_INTR,
1579 TYPE_STREAM,
1580 TYPE_COMMAND,
1581 TYPE_EVENT,
1582 };
1583
xhci_ring_type_string(enum xhci_ring_type type)1584 static inline const char *xhci_ring_type_string(enum xhci_ring_type type)
1585 {
1586 switch (type) {
1587 case TYPE_CTRL:
1588 return "CTRL";
1589 case TYPE_ISOC:
1590 return "ISOC";
1591 case TYPE_BULK:
1592 return "BULK";
1593 case TYPE_INTR:
1594 return "INTR";
1595 case TYPE_STREAM:
1596 return "STREAM";
1597 case TYPE_COMMAND:
1598 return "CMD";
1599 case TYPE_EVENT:
1600 return "EVENT";
1601 }
1602
1603 return "UNKNOWN";
1604 }
1605
1606 struct xhci_ring {
1607 struct xhci_segment *first_seg;
1608 struct xhci_segment *last_seg;
1609 union xhci_trb *enqueue;
1610 struct xhci_segment *enq_seg;
1611 union xhci_trb *dequeue;
1612 struct xhci_segment *deq_seg;
1613 struct list_head td_list;
1614 /*
1615 * Write the cycle state into the TRB cycle field to give ownership of
1616 * the TRB to the host controller (if we are the producer), or to check
1617 * if we own the TRB (if we are the consumer). See section 4.9.1.
1618 */
1619 u32 cycle_state;
1620 unsigned int stream_id;
1621 unsigned int num_segs;
1622 unsigned int num_trbs_free;
1623 unsigned int num_trbs_free_temp;
1624 unsigned int bounce_buf_len;
1625 enum xhci_ring_type type;
1626 bool last_td_was_short;
1627 struct radix_tree_root *trb_address_map;
1628 };
1629
1630 struct xhci_erst_entry {
1631 /* 64-bit event ring segment address */
1632 __le64 seg_addr;
1633 __le32 seg_size;
1634 /* Set to zero */
1635 __le32 rsvd;
1636 };
1637
1638 struct xhci_erst {
1639 struct xhci_erst_entry *entries;
1640 unsigned int num_entries;
1641 /* xhci->event_ring keeps track of segment dma addresses */
1642 dma_addr_t erst_dma_addr;
1643 /* Num entries the ERST can contain */
1644 unsigned int erst_size;
1645 };
1646
1647 struct xhci_scratchpad {
1648 u64 *sp_array;
1649 dma_addr_t sp_dma;
1650 void **sp_buffers;
1651 };
1652
1653 struct urb_priv {
1654 int num_tds;
1655 int num_tds_done;
1656 struct xhci_td td[];
1657 };
1658
1659 /*
1660 * Each segment table entry is 4*32bits long. 1K seems like an ok size:
1661 * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
1662 * meaning 64 ring segments.
1663 * Initial allocated size of the ERST, in number of entries */
1664 #define ERST_NUM_SEGS 1
1665 /* Initial allocated size of the ERST, in number of entries */
1666 #define ERST_SIZE 64
1667 /* Initial number of event segment rings allocated */
1668 #define ERST_ENTRIES 1
1669 /* Poll every 60 seconds */
1670 #define POLL_TIMEOUT 60
1671 /* Stop endpoint command timeout (secs) for URB cancellation watchdog timer */
1672 #define XHCI_STOP_EP_CMD_TIMEOUT 5
1673 /* XXX: Make these module parameters */
1674
1675 struct s3_save {
1676 u32 command;
1677 u32 dev_nt;
1678 u64 dcbaa_ptr;
1679 u32 config_reg;
1680 u32 irq_pending;
1681 u32 irq_control;
1682 u32 erst_size;
1683 u64 erst_base;
1684 u64 erst_dequeue;
1685 };
1686
1687 /* Use for lpm */
1688 struct dev_info {
1689 u32 dev_id;
1690 struct list_head list;
1691 };
1692
1693 struct xhci_bus_state {
1694 unsigned long bus_suspended;
1695 unsigned long next_statechange;
1696
1697 /* Port suspend arrays are indexed by the portnum of the fake roothub */
1698 /* ports suspend status arrays - max 31 ports for USB2, 15 for USB3 */
1699 u32 port_c_suspend;
1700 u32 suspended_ports;
1701 u32 port_remote_wakeup;
1702 unsigned long resume_done[USB_MAXCHILDREN];
1703 /* which ports have started to resume */
1704 unsigned long resuming_ports;
1705 /* Which ports are waiting on RExit to U0 transition. */
1706 unsigned long rexit_ports;
1707 struct completion rexit_done[USB_MAXCHILDREN];
1708 struct completion u3exit_done[USB_MAXCHILDREN];
1709 };
1710
1711
1712 /*
1713 * It can take up to 20 ms to transition from RExit to U0 on the
1714 * Intel Lynx Point LP xHCI host.
1715 */
1716 #define XHCI_MAX_REXIT_TIMEOUT_MS 20
1717 struct xhci_port_cap {
1718 u32 *psi; /* array of protocol speed ID entries */
1719 u8 psi_count;
1720 u8 psi_uid_count;
1721 u8 maj_rev;
1722 u8 min_rev;
1723 };
1724
1725 struct xhci_port {
1726 __le32 __iomem *addr;
1727 int hw_portnum;
1728 int hcd_portnum;
1729 struct xhci_hub *rhub;
1730 struct xhci_port_cap *port_cap;
1731 unsigned int lpm_incapable:1;
1732 };
1733
1734 struct xhci_hub {
1735 struct xhci_port **ports;
1736 unsigned int num_ports;
1737 struct usb_hcd *hcd;
1738 /* keep track of bus suspend info */
1739 struct xhci_bus_state bus_state;
1740 /* supported prococol extended capabiliy values */
1741 u8 maj_rev;
1742 u8 min_rev;
1743 };
1744
1745 /* There is one xhci_hcd structure per controller */
1746 struct xhci_hcd {
1747 struct usb_hcd *main_hcd;
1748 struct usb_hcd *shared_hcd;
1749 /* glue to PCI and HCD framework */
1750 struct xhci_cap_regs __iomem *cap_regs;
1751 struct xhci_op_regs __iomem *op_regs;
1752 struct xhci_run_regs __iomem *run_regs;
1753 struct xhci_doorbell_array __iomem *dba;
1754 /* Our HCD's current interrupter register set */
1755 struct xhci_intr_reg __iomem *ir_set;
1756
1757 /* Cached register copies of read-only HC data */
1758 __u32 hcs_params1;
1759 __u32 hcs_params2;
1760 __u32 hcs_params3;
1761 __u32 hcc_params;
1762 __u32 hcc_params2;
1763
1764 spinlock_t lock;
1765
1766 /* packed release number */
1767 u8 sbrn;
1768 u16 hci_version;
1769 u8 max_slots;
1770 u8 max_interrupters;
1771 u8 max_ports;
1772 u8 isoc_threshold;
1773 /* imod_interval in ns (I * 250ns) */
1774 u32 imod_interval;
1775 int event_ring_max;
1776 /* 4KB min, 128MB max */
1777 int page_size;
1778 /* Valid values are 12 to 20, inclusive */
1779 int page_shift;
1780 /* msi-x vectors */
1781 int msix_count;
1782 /* optional clocks */
1783 struct clk *clk;
1784 struct clk *reg_clk;
1785 /* optional reset controller */
1786 struct reset_control *reset;
1787 /* data structures */
1788 struct xhci_device_context_array *dcbaa;
1789 struct xhci_ring *cmd_ring;
1790 unsigned int cmd_ring_state;
1791 #define CMD_RING_STATE_RUNNING (1 << 0)
1792 #define CMD_RING_STATE_ABORTED (1 << 1)
1793 #define CMD_RING_STATE_STOPPED (1 << 2)
1794 struct list_head cmd_list;
1795 unsigned int cmd_ring_reserved_trbs;
1796 struct delayed_work cmd_timer;
1797 struct completion cmd_ring_stop_completion;
1798 struct xhci_command *current_cmd;
1799 struct xhci_ring *event_ring;
1800 struct xhci_erst erst;
1801 /* Scratchpad */
1802 struct xhci_scratchpad *scratchpad;
1803 /* Store LPM test failed devices' information */
1804 struct list_head lpm_failed_devs;
1805
1806 /* slot enabling and address device helpers */
1807 /* these are not thread safe so use mutex */
1808 struct mutex mutex;
1809 /* For USB 3.0 LPM enable/disable. */
1810 struct xhci_command *lpm_command;
1811 /* Internal mirror of the HW's dcbaa */
1812 struct xhci_virt_device *devs[MAX_HC_SLOTS];
1813 /* For keeping track of bandwidth domains per roothub. */
1814 struct xhci_root_port_bw_info *rh_bw;
1815
1816 /* DMA pools */
1817 struct dma_pool *device_pool;
1818 struct dma_pool *segment_pool;
1819 struct dma_pool *small_streams_pool;
1820 struct dma_pool *medium_streams_pool;
1821
1822 /* Host controller watchdog timer structures */
1823 unsigned int xhc_state;
1824 unsigned long run_graceperiod;
1825 u32 command;
1826 struct s3_save s3;
1827 /* Host controller is dying - not responding to commands. "I'm not dead yet!"
1828 *
1829 * xHC interrupts have been disabled and a watchdog timer will (or has already)
1830 * halt the xHCI host, and complete all URBs with an -ESHUTDOWN code. Any code
1831 * that sees this status (other than the timer that set it) should stop touching
1832 * hardware immediately. Interrupt handlers should return immediately when
1833 * they see this status (any time they drop and re-acquire xhci->lock).
1834 * xhci_urb_dequeue() should call usb_hcd_check_unlink_urb() and return without
1835 * putting the TD on the canceled list, etc.
1836 *
1837 * There are no reports of xHCI host controllers that display this issue.
1838 */
1839 #define XHCI_STATE_DYING (1 << 0)
1840 #define XHCI_STATE_HALTED (1 << 1)
1841 #define XHCI_STATE_REMOVING (1 << 2)
1842 unsigned long long quirks;
1843 #define XHCI_LINK_TRB_QUIRK BIT_ULL(0)
1844 #define XHCI_RESET_EP_QUIRK BIT_ULL(1)
1845 #define XHCI_NEC_HOST BIT_ULL(2)
1846 #define XHCI_AMD_PLL_FIX BIT_ULL(3)
1847 #define XHCI_SPURIOUS_SUCCESS BIT_ULL(4)
1848 /*
1849 * Certain Intel host controllers have a limit to the number of endpoint
1850 * contexts they can handle. Ideally, they would signal that they can't handle
1851 * anymore endpoint contexts by returning a Resource Error for the Configure
1852 * Endpoint command, but they don't. Instead they expect software to keep track
1853 * of the number of active endpoints for them, across configure endpoint
1854 * commands, reset device commands, disable slot commands, and address device
1855 * commands.
1856 */
1857 #define XHCI_EP_LIMIT_QUIRK BIT_ULL(5)
1858 #define XHCI_BROKEN_MSI BIT_ULL(6)
1859 #define XHCI_RESET_ON_RESUME BIT_ULL(7)
1860 #define XHCI_SW_BW_CHECKING BIT_ULL(8)
1861 #define XHCI_AMD_0x96_HOST BIT_ULL(9)
1862 #define XHCI_TRUST_TX_LENGTH BIT_ULL(10)
1863 #define XHCI_LPM_SUPPORT BIT_ULL(11)
1864 #define XHCI_INTEL_HOST BIT_ULL(12)
1865 #define XHCI_SPURIOUS_REBOOT BIT_ULL(13)
1866 #define XHCI_COMP_MODE_QUIRK BIT_ULL(14)
1867 #define XHCI_AVOID_BEI BIT_ULL(15)
1868 #define XHCI_PLAT BIT_ULL(16)
1869 #define XHCI_SLOW_SUSPEND BIT_ULL(17)
1870 #define XHCI_SPURIOUS_WAKEUP BIT_ULL(18)
1871 /* For controllers with a broken beyond repair streams implementation */
1872 #define XHCI_BROKEN_STREAMS BIT_ULL(19)
1873 #define XHCI_PME_STUCK_QUIRK BIT_ULL(20)
1874 #define XHCI_MTK_HOST BIT_ULL(21)
1875 #define XHCI_SSIC_PORT_UNUSED BIT_ULL(22)
1876 #define XHCI_NO_64BIT_SUPPORT BIT_ULL(23)
1877 #define XHCI_MISSING_CAS BIT_ULL(24)
1878 /* For controller with a broken Port Disable implementation */
1879 #define XHCI_BROKEN_PORT_PED BIT_ULL(25)
1880 #define XHCI_LIMIT_ENDPOINT_INTERVAL_7 BIT_ULL(26)
1881 #define XHCI_U2_DISABLE_WAKE BIT_ULL(27)
1882 #define XHCI_ASMEDIA_MODIFY_FLOWCONTROL BIT_ULL(28)
1883 #define XHCI_HW_LPM_DISABLE BIT_ULL(29)
1884 #define XHCI_SUSPEND_DELAY BIT_ULL(30)
1885 #define XHCI_INTEL_USB_ROLE_SW BIT_ULL(31)
1886 #define XHCI_ZERO_64B_REGS BIT_ULL(32)
1887 #define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33)
1888 #define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34)
1889 #define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35)
1890 #define XHCI_RENESAS_FW_QUIRK BIT_ULL(36)
1891 #define XHCI_SKIP_PHY_INIT BIT_ULL(37)
1892 #define XHCI_DISABLE_SPARSE BIT_ULL(38)
1893 #define XHCI_SG_TRB_CACHE_SIZE_QUIRK BIT_ULL(39)
1894 #define XHCI_NO_SOFT_RETRY BIT_ULL(40)
1895 #define XHCI_EP_CTX_BROKEN_DCS BIT_ULL(42)
1896 #define XHCI_SUSPEND_RESUME_CLKS BIT_ULL(43)
1897 #define XHCI_RESET_TO_DEFAULT BIT_ULL(44)
1898
1899 unsigned int num_active_eps;
1900 unsigned int limit_active_eps;
1901 struct xhci_port *hw_ports;
1902 struct xhci_hub usb2_rhub;
1903 struct xhci_hub usb3_rhub;
1904 /* support xHCI 1.0 spec USB2 hardware LPM */
1905 unsigned hw_lpm_support:1;
1906 /* Broken Suspend flag for SNPS Suspend resume issue */
1907 unsigned broken_suspend:1;
1908 /* cached usb2 extened protocol capabilites */
1909 u32 *ext_caps;
1910 unsigned int num_ext_caps;
1911 /* cached extended protocol port capabilities */
1912 struct xhci_port_cap *port_caps;
1913 unsigned int num_port_caps;
1914 /* Compliance Mode Recovery Data */
1915 struct timer_list comp_mode_recovery_timer;
1916 u32 port_status_u0;
1917 u16 test_mode;
1918 /* Compliance Mode Timer Triggered every 2 seconds */
1919 #define COMP_MODE_RCVRY_MSECS 2000
1920
1921 struct dentry *debugfs_root;
1922 struct dentry *debugfs_slots;
1923 struct list_head regset_list;
1924
1925 void *dbc;
1926 /* platform-specific data -- must come last */
1927 unsigned long priv[] __aligned(sizeof(s64));
1928 };
1929
1930 /* Platform specific overrides to generic XHCI hc_driver ops */
1931 struct xhci_driver_overrides {
1932 size_t extra_priv_size;
1933 int (*reset)(struct usb_hcd *hcd);
1934 int (*start)(struct usb_hcd *hcd);
1935 int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
1936 void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
1937 int (*update_hub_device)(struct usb_hcd *hcd, struct usb_device *hdev,
1938 struct usb_tt *tt, gfp_t mem_flags);
1939 };
1940
1941 #define XHCI_CFC_DELAY 10
1942
1943 /* convert between an HCD pointer and the corresponding EHCI_HCD */
hcd_to_xhci(struct usb_hcd * hcd)1944 static inline struct xhci_hcd *hcd_to_xhci(struct usb_hcd *hcd)
1945 {
1946 struct usb_hcd *primary_hcd;
1947
1948 if (usb_hcd_is_primary_hcd(hcd))
1949 primary_hcd = hcd;
1950 else
1951 primary_hcd = hcd->primary_hcd;
1952
1953 return (struct xhci_hcd *) (primary_hcd->hcd_priv);
1954 }
1955
xhci_to_hcd(struct xhci_hcd * xhci)1956 static inline struct usb_hcd *xhci_to_hcd(struct xhci_hcd *xhci)
1957 {
1958 return xhci->main_hcd;
1959 }
1960
1961 #define xhci_dbg(xhci, fmt, args...) \
1962 dev_dbg(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1963 #define xhci_err(xhci, fmt, args...) \
1964 dev_err(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1965 #define xhci_warn(xhci, fmt, args...) \
1966 dev_warn(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1967 #define xhci_warn_ratelimited(xhci, fmt, args...) \
1968 dev_warn_ratelimited(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1969 #define xhci_info(xhci, fmt, args...) \
1970 dev_info(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1971
1972 /*
1973 * Registers should always be accessed with double word or quad word accesses.
1974 *
1975 * Some xHCI implementations may support 64-bit address pointers. Registers
1976 * with 64-bit address pointers should be written to with dword accesses by
1977 * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
1978 * xHCI implementations that do not support 64-bit address pointers will ignore
1979 * the high dword, and write order is irrelevant.
1980 */
xhci_read_64(const struct xhci_hcd * xhci,__le64 __iomem * regs)1981 static inline u64 xhci_read_64(const struct xhci_hcd *xhci,
1982 __le64 __iomem *regs)
1983 {
1984 return lo_hi_readq(regs);
1985 }
xhci_write_64(struct xhci_hcd * xhci,const u64 val,__le64 __iomem * regs)1986 static inline void xhci_write_64(struct xhci_hcd *xhci,
1987 const u64 val, __le64 __iomem *regs)
1988 {
1989 lo_hi_writeq(val, regs);
1990 }
1991
xhci_link_trb_quirk(struct xhci_hcd * xhci)1992 static inline int xhci_link_trb_quirk(struct xhci_hcd *xhci)
1993 {
1994 return xhci->quirks & XHCI_LINK_TRB_QUIRK;
1995 }
1996
1997 /* xHCI debugging */
1998 char *xhci_get_slot_state(struct xhci_hcd *xhci,
1999 struct xhci_container_ctx *ctx);
2000 void xhci_dbg_trace(struct xhci_hcd *xhci, void (*trace)(struct va_format *),
2001 const char *fmt, ...);
2002
2003 /* xHCI memory management */
2004 void xhci_mem_cleanup(struct xhci_hcd *xhci);
2005 int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags);
2006 void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id);
2007 int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, struct usb_device *udev, gfp_t flags);
2008 int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *udev);
2009 void xhci_copy_ep0_dequeue_into_input_ctx(struct xhci_hcd *xhci,
2010 struct usb_device *udev);
2011 unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc);
2012 unsigned int xhci_get_endpoint_address(unsigned int ep_index);
2013 unsigned int xhci_last_valid_endpoint(u32 added_ctxs);
2014 void xhci_endpoint_zero(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev, struct usb_host_endpoint *ep);
2015 void xhci_update_tt_active_eps(struct xhci_hcd *xhci,
2016 struct xhci_virt_device *virt_dev,
2017 int old_active_eps);
2018 void xhci_clear_endpoint_bw_info(struct xhci_bw_info *bw_info);
2019 void xhci_update_bw_info(struct xhci_hcd *xhci,
2020 struct xhci_container_ctx *in_ctx,
2021 struct xhci_input_control_ctx *ctrl_ctx,
2022 struct xhci_virt_device *virt_dev);
2023 void xhci_endpoint_copy(struct xhci_hcd *xhci,
2024 struct xhci_container_ctx *in_ctx,
2025 struct xhci_container_ctx *out_ctx,
2026 unsigned int ep_index);
2027 void xhci_slot_copy(struct xhci_hcd *xhci,
2028 struct xhci_container_ctx *in_ctx,
2029 struct xhci_container_ctx *out_ctx);
2030 int xhci_endpoint_init(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev,
2031 struct usb_device *udev, struct usb_host_endpoint *ep,
2032 gfp_t mem_flags);
2033 struct xhci_ring *xhci_ring_alloc(struct xhci_hcd *xhci,
2034 unsigned int num_segs, unsigned int cycle_state,
2035 enum xhci_ring_type type, unsigned int max_packet, gfp_t flags);
2036 void xhci_ring_free(struct xhci_hcd *xhci, struct xhci_ring *ring);
2037 int xhci_ring_expansion(struct xhci_hcd *xhci, struct xhci_ring *ring,
2038 unsigned int num_trbs, gfp_t flags);
2039 int xhci_alloc_erst(struct xhci_hcd *xhci,
2040 struct xhci_ring *evt_ring,
2041 struct xhci_erst *erst,
2042 gfp_t flags);
2043 void xhci_initialize_ring_info(struct xhci_ring *ring,
2044 unsigned int cycle_state);
2045 void xhci_free_erst(struct xhci_hcd *xhci, struct xhci_erst *erst);
2046 void xhci_free_endpoint_ring(struct xhci_hcd *xhci,
2047 struct xhci_virt_device *virt_dev,
2048 unsigned int ep_index);
2049 struct xhci_stream_info *xhci_alloc_stream_info(struct xhci_hcd *xhci,
2050 unsigned int num_stream_ctxs,
2051 unsigned int num_streams,
2052 unsigned int max_packet, gfp_t flags);
2053 void xhci_free_stream_info(struct xhci_hcd *xhci,
2054 struct xhci_stream_info *stream_info);
2055 void xhci_setup_streams_ep_input_ctx(struct xhci_hcd *xhci,
2056 struct xhci_ep_ctx *ep_ctx,
2057 struct xhci_stream_info *stream_info);
2058 void xhci_setup_no_streams_ep_input_ctx(struct xhci_ep_ctx *ep_ctx,
2059 struct xhci_virt_ep *ep);
2060 void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci,
2061 struct xhci_virt_device *virt_dev, bool drop_control_ep);
2062 struct xhci_ring *xhci_dma_to_transfer_ring(
2063 struct xhci_virt_ep *ep,
2064 u64 address);
2065 struct xhci_ring *xhci_stream_id_to_ring(
2066 struct xhci_virt_device *dev,
2067 unsigned int ep_index,
2068 unsigned int stream_id);
2069 struct xhci_command *xhci_alloc_command(struct xhci_hcd *xhci,
2070 bool allocate_completion, gfp_t mem_flags);
2071 struct xhci_command *xhci_alloc_command_with_ctx(struct xhci_hcd *xhci,
2072 bool allocate_completion, gfp_t mem_flags);
2073 void xhci_urb_free_priv(struct urb_priv *urb_priv);
2074 void xhci_free_command(struct xhci_hcd *xhci,
2075 struct xhci_command *command);
2076 struct xhci_container_ctx *xhci_alloc_container_ctx(struct xhci_hcd *xhci,
2077 int type, gfp_t flags);
2078 void xhci_free_container_ctx(struct xhci_hcd *xhci,
2079 struct xhci_container_ctx *ctx);
2080
2081 /* xHCI host controller glue */
2082 typedef void (*xhci_get_quirks_t)(struct device *, struct xhci_hcd *);
2083 int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, u64 timeout_us);
2084 void xhci_quiesce(struct xhci_hcd *xhci);
2085 int xhci_halt(struct xhci_hcd *xhci);
2086 int xhci_start(struct xhci_hcd *xhci);
2087 int xhci_reset(struct xhci_hcd *xhci, u64 timeout_us);
2088 int xhci_run(struct usb_hcd *hcd);
2089 int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks);
2090 void xhci_shutdown(struct usb_hcd *hcd);
2091 void xhci_init_driver(struct hc_driver *drv,
2092 const struct xhci_driver_overrides *over);
2093 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
2094 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
2095 int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
2096 struct usb_tt *tt, gfp_t mem_flags);
2097 int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id);
2098 int xhci_ext_cap_init(struct xhci_hcd *xhci);
2099
2100 int xhci_suspend(struct xhci_hcd *xhci, bool do_wakeup);
2101 int xhci_resume(struct xhci_hcd *xhci, bool hibernated);
2102
2103 irqreturn_t xhci_irq(struct usb_hcd *hcd);
2104 irqreturn_t xhci_msi_irq(int irq, void *hcd);
2105 int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev);
2106 int xhci_alloc_tt_info(struct xhci_hcd *xhci,
2107 struct xhci_virt_device *virt_dev,
2108 struct usb_device *hdev,
2109 struct usb_tt *tt, gfp_t mem_flags);
2110
2111 /* xHCI ring, segment, TRB, and TD functions */
2112 dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg, union xhci_trb *trb);
2113 struct xhci_segment *trb_in_td(struct xhci_hcd *xhci,
2114 struct xhci_segment *start_seg, union xhci_trb *start_trb,
2115 union xhci_trb *end_trb, dma_addr_t suspect_dma, bool debug);
2116 int xhci_is_vendor_info_code(struct xhci_hcd *xhci, unsigned int trb_comp_code);
2117 void xhci_ring_cmd_db(struct xhci_hcd *xhci);
2118 int xhci_queue_slot_control(struct xhci_hcd *xhci, struct xhci_command *cmd,
2119 u32 trb_type, u32 slot_id);
2120 int xhci_queue_address_device(struct xhci_hcd *xhci, struct xhci_command *cmd,
2121 dma_addr_t in_ctx_ptr, u32 slot_id, enum xhci_setup_dev);
2122 int xhci_queue_vendor_command(struct xhci_hcd *xhci, struct xhci_command *cmd,
2123 u32 field1, u32 field2, u32 field3, u32 field4);
2124 int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, struct xhci_command *cmd,
2125 int slot_id, unsigned int ep_index, int suspend);
2126 int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
2127 int slot_id, unsigned int ep_index);
2128 int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
2129 int slot_id, unsigned int ep_index);
2130 int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
2131 int slot_id, unsigned int ep_index);
2132 int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags,
2133 struct urb *urb, int slot_id, unsigned int ep_index);
2134 int xhci_queue_configure_endpoint(struct xhci_hcd *xhci,
2135 struct xhci_command *cmd, dma_addr_t in_ctx_ptr, u32 slot_id,
2136 bool command_must_succeed);
2137 int xhci_queue_evaluate_context(struct xhci_hcd *xhci, struct xhci_command *cmd,
2138 dma_addr_t in_ctx_ptr, u32 slot_id, bool command_must_succeed);
2139 int xhci_queue_reset_ep(struct xhci_hcd *xhci, struct xhci_command *cmd,
2140 int slot_id, unsigned int ep_index,
2141 enum xhci_ep_reset_type reset_type);
2142 int xhci_queue_reset_device(struct xhci_hcd *xhci, struct xhci_command *cmd,
2143 u32 slot_id);
2144 void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
2145 unsigned int slot_id, unsigned int ep_index,
2146 unsigned int stream_id, struct xhci_td *cur_td,
2147 struct xhci_dequeue_state *state);
2148 void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
2149 unsigned int slot_id, unsigned int ep_index,
2150 struct xhci_dequeue_state *deq_state);
2151 void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci, unsigned int slot_id,
2152 unsigned int ep_index, unsigned int stream_id,
2153 struct xhci_td *td);
2154 void xhci_stop_endpoint_command_watchdog(struct timer_list *t);
2155 void xhci_handle_command_timeout(struct work_struct *work);
2156
2157 void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, unsigned int slot_id,
2158 unsigned int ep_index, unsigned int stream_id);
2159 void xhci_ring_doorbell_for_active_rings(struct xhci_hcd *xhci,
2160 unsigned int slot_id,
2161 unsigned int ep_index);
2162 void xhci_cleanup_command_queue(struct xhci_hcd *xhci);
2163 void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring);
2164 unsigned int count_trbs(u64 addr, u64 len);
2165
2166 /* xHCI roothub code */
2167 void xhci_set_link_state(struct xhci_hcd *xhci, struct xhci_port *port,
2168 u32 link_state);
2169 void xhci_test_and_clear_bit(struct xhci_hcd *xhci, struct xhci_port *port,
2170 u32 port_bit);
2171 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
2172 char *buf, u16 wLength);
2173 int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
2174 int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1);
2175 struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd);
2176
2177 void xhci_hc_died(struct xhci_hcd *xhci);
2178
2179 #ifdef CONFIG_PM
2180 int xhci_bus_suspend(struct usb_hcd *hcd);
2181 int xhci_bus_resume(struct usb_hcd *hcd);
2182 unsigned long xhci_get_resuming_ports(struct usb_hcd *hcd);
2183 #else
2184 #define xhci_bus_suspend NULL
2185 #define xhci_bus_resume NULL
2186 #define xhci_get_resuming_ports NULL
2187 #endif /* CONFIG_PM */
2188
2189 u32 xhci_port_state_to_neutral(u32 state);
2190 int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
2191 u16 port);
2192 void xhci_ring_device(struct xhci_hcd *xhci, int slot_id);
2193
2194 /* xHCI contexts */
2195 struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_container_ctx *ctx);
2196 struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
2197 struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index);
2198
2199 struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci,
2200 unsigned int slot_id, unsigned int ep_index,
2201 unsigned int stream_id);
2202
xhci_urb_to_transfer_ring(struct xhci_hcd * xhci,struct urb * urb)2203 static inline struct xhci_ring *xhci_urb_to_transfer_ring(struct xhci_hcd *xhci,
2204 struct urb *urb)
2205 {
2206 return xhci_triad_to_transfer_ring(xhci, urb->dev->slot_id,
2207 xhci_get_endpoint_index(&urb->ep->desc),
2208 urb->stream_id);
2209 }
2210
2211 /*
2212 * TODO: As per spec Isochronous IDT transmissions are supported. We bypass
2213 * them anyways as we where unable to find a device that matches the
2214 * constraints.
2215 */
xhci_urb_suitable_for_idt(struct urb * urb)2216 static inline bool xhci_urb_suitable_for_idt(struct urb *urb)
2217 {
2218 if (!usb_endpoint_xfer_isoc(&urb->ep->desc) && usb_urb_dir_out(urb) &&
2219 usb_endpoint_maxp(&urb->ep->desc) >= TRB_IDT_MAX_SIZE &&
2220 urb->transfer_buffer_length <= TRB_IDT_MAX_SIZE &&
2221 !(urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP) &&
2222 !urb->num_sgs)
2223 return true;
2224
2225 return false;
2226 }
2227
xhci_slot_state_string(u32 state)2228 static inline char *xhci_slot_state_string(u32 state)
2229 {
2230 switch (state) {
2231 case SLOT_STATE_ENABLED:
2232 return "enabled/disabled";
2233 case SLOT_STATE_DEFAULT:
2234 return "default";
2235 case SLOT_STATE_ADDRESSED:
2236 return "addressed";
2237 case SLOT_STATE_CONFIGURED:
2238 return "configured";
2239 default:
2240 return "reserved";
2241 }
2242 }
2243
xhci_decode_trb(char * str,size_t size,u32 field0,u32 field1,u32 field2,u32 field3)2244 static inline const char *xhci_decode_trb(char *str, size_t size,
2245 u32 field0, u32 field1, u32 field2, u32 field3)
2246 {
2247 int type = TRB_FIELD_TO_TYPE(field3);
2248
2249 switch (type) {
2250 case TRB_LINK:
2251 snprintf(str, size,
2252 "LINK %08x%08x intr %d type '%s' flags %c:%c:%c:%c",
2253 field1, field0, GET_INTR_TARGET(field2),
2254 xhci_trb_type_string(type),
2255 field3 & TRB_IOC ? 'I' : 'i',
2256 field3 & TRB_CHAIN ? 'C' : 'c',
2257 field3 & TRB_TC ? 'T' : 't',
2258 field3 & TRB_CYCLE ? 'C' : 'c');
2259 break;
2260 case TRB_TRANSFER:
2261 case TRB_COMPLETION:
2262 case TRB_PORT_STATUS:
2263 case TRB_BANDWIDTH_EVENT:
2264 case TRB_DOORBELL:
2265 case TRB_HC_EVENT:
2266 case TRB_DEV_NOTE:
2267 case TRB_MFINDEX_WRAP:
2268 snprintf(str, size,
2269 "TRB %08x%08x status '%s' len %d slot %d ep %d type '%s' flags %c:%c",
2270 field1, field0,
2271 xhci_trb_comp_code_string(GET_COMP_CODE(field2)),
2272 EVENT_TRB_LEN(field2), TRB_TO_SLOT_ID(field3),
2273 /* Macro decrements 1, maybe it shouldn't?!? */
2274 TRB_TO_EP_INDEX(field3) + 1,
2275 xhci_trb_type_string(type),
2276 field3 & EVENT_DATA ? 'E' : 'e',
2277 field3 & TRB_CYCLE ? 'C' : 'c');
2278
2279 break;
2280 case TRB_SETUP:
2281 snprintf(str, size,
2282 "bRequestType %02x bRequest %02x wValue %02x%02x wIndex %02x%02x wLength %d length %d TD size %d intr %d type '%s' flags %c:%c:%c",
2283 field0 & 0xff,
2284 (field0 & 0xff00) >> 8,
2285 (field0 & 0xff000000) >> 24,
2286 (field0 & 0xff0000) >> 16,
2287 (field1 & 0xff00) >> 8,
2288 field1 & 0xff,
2289 (field1 & 0xff000000) >> 16 |
2290 (field1 & 0xff0000) >> 16,
2291 TRB_LEN(field2), GET_TD_SIZE(field2),
2292 GET_INTR_TARGET(field2),
2293 xhci_trb_type_string(type),
2294 field3 & TRB_IDT ? 'I' : 'i',
2295 field3 & TRB_IOC ? 'I' : 'i',
2296 field3 & TRB_CYCLE ? 'C' : 'c');
2297 break;
2298 case TRB_DATA:
2299 snprintf(str, size,
2300 "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c",
2301 field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2),
2302 GET_INTR_TARGET(field2),
2303 xhci_trb_type_string(type),
2304 field3 & TRB_IDT ? 'I' : 'i',
2305 field3 & TRB_IOC ? 'I' : 'i',
2306 field3 & TRB_CHAIN ? 'C' : 'c',
2307 field3 & TRB_NO_SNOOP ? 'S' : 's',
2308 field3 & TRB_ISP ? 'I' : 'i',
2309 field3 & TRB_ENT ? 'E' : 'e',
2310 field3 & TRB_CYCLE ? 'C' : 'c');
2311 break;
2312 case TRB_STATUS:
2313 snprintf(str, size,
2314 "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c",
2315 field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2),
2316 GET_INTR_TARGET(field2),
2317 xhci_trb_type_string(type),
2318 field3 & TRB_IOC ? 'I' : 'i',
2319 field3 & TRB_CHAIN ? 'C' : 'c',
2320 field3 & TRB_ENT ? 'E' : 'e',
2321 field3 & TRB_CYCLE ? 'C' : 'c');
2322 break;
2323 case TRB_NORMAL:
2324 case TRB_ISOC:
2325 case TRB_EVENT_DATA:
2326 case TRB_TR_NOOP:
2327 snprintf(str, size,
2328 "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c:%c",
2329 field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2),
2330 GET_INTR_TARGET(field2),
2331 xhci_trb_type_string(type),
2332 field3 & TRB_BEI ? 'B' : 'b',
2333 field3 & TRB_IDT ? 'I' : 'i',
2334 field3 & TRB_IOC ? 'I' : 'i',
2335 field3 & TRB_CHAIN ? 'C' : 'c',
2336 field3 & TRB_NO_SNOOP ? 'S' : 's',
2337 field3 & TRB_ISP ? 'I' : 'i',
2338 field3 & TRB_ENT ? 'E' : 'e',
2339 field3 & TRB_CYCLE ? 'C' : 'c');
2340 break;
2341
2342 case TRB_CMD_NOOP:
2343 case TRB_ENABLE_SLOT:
2344 snprintf(str, size,
2345 "%s: flags %c",
2346 xhci_trb_type_string(type),
2347 field3 & TRB_CYCLE ? 'C' : 'c');
2348 break;
2349 case TRB_DISABLE_SLOT:
2350 case TRB_NEG_BANDWIDTH:
2351 snprintf(str, size,
2352 "%s: slot %d flags %c",
2353 xhci_trb_type_string(type),
2354 TRB_TO_SLOT_ID(field3),
2355 field3 & TRB_CYCLE ? 'C' : 'c');
2356 break;
2357 case TRB_ADDR_DEV:
2358 snprintf(str, size,
2359 "%s: ctx %08x%08x slot %d flags %c:%c",
2360 xhci_trb_type_string(type),
2361 field1, field0,
2362 TRB_TO_SLOT_ID(field3),
2363 field3 & TRB_BSR ? 'B' : 'b',
2364 field3 & TRB_CYCLE ? 'C' : 'c');
2365 break;
2366 case TRB_CONFIG_EP:
2367 snprintf(str, size,
2368 "%s: ctx %08x%08x slot %d flags %c:%c",
2369 xhci_trb_type_string(type),
2370 field1, field0,
2371 TRB_TO_SLOT_ID(field3),
2372 field3 & TRB_DC ? 'D' : 'd',
2373 field3 & TRB_CYCLE ? 'C' : 'c');
2374 break;
2375 case TRB_EVAL_CONTEXT:
2376 snprintf(str, size,
2377 "%s: ctx %08x%08x slot %d flags %c",
2378 xhci_trb_type_string(type),
2379 field1, field0,
2380 TRB_TO_SLOT_ID(field3),
2381 field3 & TRB_CYCLE ? 'C' : 'c');
2382 break;
2383 case TRB_RESET_EP:
2384 snprintf(str, size,
2385 "%s: ctx %08x%08x slot %d ep %d flags %c:%c",
2386 xhci_trb_type_string(type),
2387 field1, field0,
2388 TRB_TO_SLOT_ID(field3),
2389 /* Macro decrements 1, maybe it shouldn't?!? */
2390 TRB_TO_EP_INDEX(field3) + 1,
2391 field3 & TRB_TSP ? 'T' : 't',
2392 field3 & TRB_CYCLE ? 'C' : 'c');
2393 break;
2394 case TRB_STOP_RING:
2395 snprintf(str, size,
2396 "%s: slot %d sp %d ep %d flags %c",
2397 xhci_trb_type_string(type),
2398 TRB_TO_SLOT_ID(field3),
2399 TRB_TO_SUSPEND_PORT(field3),
2400 /* Macro decrements 1, maybe it shouldn't?!? */
2401 TRB_TO_EP_INDEX(field3) + 1,
2402 field3 & TRB_CYCLE ? 'C' : 'c');
2403 break;
2404 case TRB_SET_DEQ:
2405 snprintf(str, size,
2406 "%s: deq %08x%08x stream %d slot %d ep %d flags %c",
2407 xhci_trb_type_string(type),
2408 field1, field0,
2409 TRB_TO_STREAM_ID(field2),
2410 TRB_TO_SLOT_ID(field3),
2411 /* Macro decrements 1, maybe it shouldn't?!? */
2412 TRB_TO_EP_INDEX(field3) + 1,
2413 field3 & TRB_CYCLE ? 'C' : 'c');
2414 break;
2415 case TRB_RESET_DEV:
2416 snprintf(str, size,
2417 "%s: slot %d flags %c",
2418 xhci_trb_type_string(type),
2419 TRB_TO_SLOT_ID(field3),
2420 field3 & TRB_CYCLE ? 'C' : 'c');
2421 break;
2422 case TRB_FORCE_EVENT:
2423 snprintf(str, size,
2424 "%s: event %08x%08x vf intr %d vf id %d flags %c",
2425 xhci_trb_type_string(type),
2426 field1, field0,
2427 TRB_TO_VF_INTR_TARGET(field2),
2428 TRB_TO_VF_ID(field3),
2429 field3 & TRB_CYCLE ? 'C' : 'c');
2430 break;
2431 case TRB_SET_LT:
2432 snprintf(str, size,
2433 "%s: belt %d flags %c",
2434 xhci_trb_type_string(type),
2435 TRB_TO_BELT(field3),
2436 field3 & TRB_CYCLE ? 'C' : 'c');
2437 break;
2438 case TRB_GET_BW:
2439 snprintf(str, size,
2440 "%s: ctx %08x%08x slot %d speed %d flags %c",
2441 xhci_trb_type_string(type),
2442 field1, field0,
2443 TRB_TO_SLOT_ID(field3),
2444 TRB_TO_DEV_SPEED(field3),
2445 field3 & TRB_CYCLE ? 'C' : 'c');
2446 break;
2447 case TRB_FORCE_HEADER:
2448 snprintf(str, size,
2449 "%s: info %08x%08x%08x pkt type %d roothub port %d flags %c",
2450 xhci_trb_type_string(type),
2451 field2, field1, field0 & 0xffffffe0,
2452 TRB_TO_PACKET_TYPE(field0),
2453 TRB_TO_ROOTHUB_PORT(field3),
2454 field3 & TRB_CYCLE ? 'C' : 'c');
2455 break;
2456 default:
2457 snprintf(str, size,
2458 "type '%s' -> raw %08x %08x %08x %08x",
2459 xhci_trb_type_string(type),
2460 field0, field1, field2, field3);
2461 }
2462
2463 return str;
2464 }
2465
xhci_decode_ctrl_ctx(char * str,unsigned long drop,unsigned long add)2466 static inline const char *xhci_decode_ctrl_ctx(char *str,
2467 unsigned long drop, unsigned long add)
2468 {
2469 unsigned int bit;
2470 int ret = 0;
2471
2472 str[0] = '\0';
2473
2474 if (drop) {
2475 ret = sprintf(str, "Drop:");
2476 for_each_set_bit(bit, &drop, 32)
2477 ret += sprintf(str + ret, " %d%s",
2478 bit / 2,
2479 bit % 2 ? "in":"out");
2480 ret += sprintf(str + ret, ", ");
2481 }
2482
2483 if (add) {
2484 ret += sprintf(str + ret, "Add:%s%s",
2485 (add & SLOT_FLAG) ? " slot":"",
2486 (add & EP0_FLAG) ? " ep0":"");
2487 add &= ~(SLOT_FLAG | EP0_FLAG);
2488 for_each_set_bit(bit, &add, 32)
2489 ret += sprintf(str + ret, " %d%s",
2490 bit / 2,
2491 bit % 2 ? "in":"out");
2492 }
2493 return str;
2494 }
2495
xhci_decode_slot_context(char * str,u32 info,u32 info2,u32 tt_info,u32 state)2496 static inline const char *xhci_decode_slot_context(char *str,
2497 u32 info, u32 info2, u32 tt_info, u32 state)
2498 {
2499 u32 speed;
2500 u32 hub;
2501 u32 mtt;
2502 int ret = 0;
2503
2504 speed = info & DEV_SPEED;
2505 hub = info & DEV_HUB;
2506 mtt = info & DEV_MTT;
2507
2508 ret = sprintf(str, "RS %05x %s%s%s Ctx Entries %d MEL %d us Port# %d/%d",
2509 info & ROUTE_STRING_MASK,
2510 ({ char *s;
2511 switch (speed) {
2512 case SLOT_SPEED_FS:
2513 s = "full-speed";
2514 break;
2515 case SLOT_SPEED_LS:
2516 s = "low-speed";
2517 break;
2518 case SLOT_SPEED_HS:
2519 s = "high-speed";
2520 break;
2521 case SLOT_SPEED_SS:
2522 s = "super-speed";
2523 break;
2524 case SLOT_SPEED_SSP:
2525 s = "super-speed plus";
2526 break;
2527 default:
2528 s = "UNKNOWN speed";
2529 } s; }),
2530 mtt ? " multi-TT" : "",
2531 hub ? " Hub" : "",
2532 (info & LAST_CTX_MASK) >> 27,
2533 info2 & MAX_EXIT,
2534 DEVINFO_TO_ROOT_HUB_PORT(info2),
2535 DEVINFO_TO_MAX_PORTS(info2));
2536
2537 ret += sprintf(str + ret, " [TT Slot %d Port# %d TTT %d Intr %d] Addr %d State %s",
2538 tt_info & TT_SLOT, (tt_info & TT_PORT) >> 8,
2539 GET_TT_THINK_TIME(tt_info), GET_INTR_TARGET(tt_info),
2540 state & DEV_ADDR_MASK,
2541 xhci_slot_state_string(GET_SLOT_STATE(state)));
2542
2543 return str;
2544 }
2545
2546
xhci_portsc_link_state_string(u32 portsc)2547 static inline const char *xhci_portsc_link_state_string(u32 portsc)
2548 {
2549 switch (portsc & PORT_PLS_MASK) {
2550 case XDEV_U0:
2551 return "U0";
2552 case XDEV_U1:
2553 return "U1";
2554 case XDEV_U2:
2555 return "U2";
2556 case XDEV_U3:
2557 return "U3";
2558 case XDEV_DISABLED:
2559 return "Disabled";
2560 case XDEV_RXDETECT:
2561 return "RxDetect";
2562 case XDEV_INACTIVE:
2563 return "Inactive";
2564 case XDEV_POLLING:
2565 return "Polling";
2566 case XDEV_RECOVERY:
2567 return "Recovery";
2568 case XDEV_HOT_RESET:
2569 return "Hot Reset";
2570 case XDEV_COMP_MODE:
2571 return "Compliance mode";
2572 case XDEV_TEST_MODE:
2573 return "Test mode";
2574 case XDEV_RESUME:
2575 return "Resume";
2576 default:
2577 break;
2578 }
2579 return "Unknown";
2580 }
2581
xhci_decode_portsc(char * str,u32 portsc)2582 static inline const char *xhci_decode_portsc(char *str, u32 portsc)
2583 {
2584 int ret;
2585
2586 ret = sprintf(str, "%s %s %s Link:%s PortSpeed:%d ",
2587 portsc & PORT_POWER ? "Powered" : "Powered-off",
2588 portsc & PORT_CONNECT ? "Connected" : "Not-connected",
2589 portsc & PORT_PE ? "Enabled" : "Disabled",
2590 xhci_portsc_link_state_string(portsc),
2591 DEV_PORT_SPEED(portsc));
2592
2593 if (portsc & PORT_OC)
2594 ret += sprintf(str + ret, "OverCurrent ");
2595 if (portsc & PORT_RESET)
2596 ret += sprintf(str + ret, "In-Reset ");
2597
2598 ret += sprintf(str + ret, "Change: ");
2599 if (portsc & PORT_CSC)
2600 ret += sprintf(str + ret, "CSC ");
2601 if (portsc & PORT_PEC)
2602 ret += sprintf(str + ret, "PEC ");
2603 if (portsc & PORT_WRC)
2604 ret += sprintf(str + ret, "WRC ");
2605 if (portsc & PORT_OCC)
2606 ret += sprintf(str + ret, "OCC ");
2607 if (portsc & PORT_RC)
2608 ret += sprintf(str + ret, "PRC ");
2609 if (portsc & PORT_PLC)
2610 ret += sprintf(str + ret, "PLC ");
2611 if (portsc & PORT_CEC)
2612 ret += sprintf(str + ret, "CEC ");
2613 if (portsc & PORT_CAS)
2614 ret += sprintf(str + ret, "CAS ");
2615
2616 ret += sprintf(str + ret, "Wake: ");
2617 if (portsc & PORT_WKCONN_E)
2618 ret += sprintf(str + ret, "WCE ");
2619 if (portsc & PORT_WKDISC_E)
2620 ret += sprintf(str + ret, "WDE ");
2621 if (portsc & PORT_WKOC_E)
2622 ret += sprintf(str + ret, "WOE ");
2623
2624 return str;
2625 }
2626
xhci_decode_usbsts(char * str,u32 usbsts)2627 static inline const char *xhci_decode_usbsts(char *str, u32 usbsts)
2628 {
2629 int ret = 0;
2630
2631 ret = sprintf(str, " 0x%08x", usbsts);
2632
2633 if (usbsts == ~(u32)0)
2634 return str;
2635
2636 if (usbsts & STS_HALT)
2637 ret += sprintf(str + ret, " HCHalted");
2638 if (usbsts & STS_FATAL)
2639 ret += sprintf(str + ret, " HSE");
2640 if (usbsts & STS_EINT)
2641 ret += sprintf(str + ret, " EINT");
2642 if (usbsts & STS_PORT)
2643 ret += sprintf(str + ret, " PCD");
2644 if (usbsts & STS_SAVE)
2645 ret += sprintf(str + ret, " SSS");
2646 if (usbsts & STS_RESTORE)
2647 ret += sprintf(str + ret, " RSS");
2648 if (usbsts & STS_SRE)
2649 ret += sprintf(str + ret, " SRE");
2650 if (usbsts & STS_CNR)
2651 ret += sprintf(str + ret, " CNR");
2652 if (usbsts & STS_HCE)
2653 ret += sprintf(str + ret, " HCE");
2654
2655 return str;
2656 }
2657
xhci_decode_doorbell(char * str,u32 slot,u32 doorbell)2658 static inline const char *xhci_decode_doorbell(char *str, u32 slot, u32 doorbell)
2659 {
2660 u8 ep;
2661 u16 stream;
2662 int ret;
2663
2664 ep = (doorbell & 0xff);
2665 stream = doorbell >> 16;
2666
2667 if (slot == 0) {
2668 sprintf(str, "Command Ring %d", doorbell);
2669 return str;
2670 }
2671 ret = sprintf(str, "Slot %d ", slot);
2672 if (ep > 0 && ep < 32)
2673 ret = sprintf(str + ret, "ep%d%s",
2674 ep / 2,
2675 ep % 2 ? "in" : "out");
2676 else if (ep == 0 || ep < 248)
2677 ret = sprintf(str + ret, "Reserved %d", ep);
2678 else
2679 ret = sprintf(str + ret, "Vendor Defined %d", ep);
2680 if (stream)
2681 ret = sprintf(str + ret, " Stream %d", stream);
2682
2683 return str;
2684 }
2685
xhci_ep_state_string(u8 state)2686 static inline const char *xhci_ep_state_string(u8 state)
2687 {
2688 switch (state) {
2689 case EP_STATE_DISABLED:
2690 return "disabled";
2691 case EP_STATE_RUNNING:
2692 return "running";
2693 case EP_STATE_HALTED:
2694 return "halted";
2695 case EP_STATE_STOPPED:
2696 return "stopped";
2697 case EP_STATE_ERROR:
2698 return "error";
2699 default:
2700 return "INVALID";
2701 }
2702 }
2703
xhci_ep_type_string(u8 type)2704 static inline const char *xhci_ep_type_string(u8 type)
2705 {
2706 switch (type) {
2707 case ISOC_OUT_EP:
2708 return "Isoc OUT";
2709 case BULK_OUT_EP:
2710 return "Bulk OUT";
2711 case INT_OUT_EP:
2712 return "Int OUT";
2713 case CTRL_EP:
2714 return "Ctrl";
2715 case ISOC_IN_EP:
2716 return "Isoc IN";
2717 case BULK_IN_EP:
2718 return "Bulk IN";
2719 case INT_IN_EP:
2720 return "Int IN";
2721 default:
2722 return "INVALID";
2723 }
2724 }
2725
xhci_decode_ep_context(char * str,u32 info,u32 info2,u64 deq,u32 tx_info)2726 static inline const char *xhci_decode_ep_context(char *str, u32 info,
2727 u32 info2, u64 deq, u32 tx_info)
2728 {
2729 int ret;
2730
2731 u32 esit;
2732 u16 maxp;
2733 u16 avg;
2734
2735 u8 max_pstr;
2736 u8 ep_state;
2737 u8 interval;
2738 u8 ep_type;
2739 u8 burst;
2740 u8 cerr;
2741 u8 mult;
2742
2743 bool lsa;
2744 bool hid;
2745
2746 esit = CTX_TO_MAX_ESIT_PAYLOAD_HI(info) << 16 |
2747 CTX_TO_MAX_ESIT_PAYLOAD(tx_info);
2748
2749 ep_state = info & EP_STATE_MASK;
2750 max_pstr = CTX_TO_EP_MAXPSTREAMS(info);
2751 interval = CTX_TO_EP_INTERVAL(info);
2752 mult = CTX_TO_EP_MULT(info) + 1;
2753 lsa = !!(info & EP_HAS_LSA);
2754
2755 cerr = (info2 & (3 << 1)) >> 1;
2756 ep_type = CTX_TO_EP_TYPE(info2);
2757 hid = !!(info2 & (1 << 7));
2758 burst = CTX_TO_MAX_BURST(info2);
2759 maxp = MAX_PACKET_DECODED(info2);
2760
2761 avg = EP_AVG_TRB_LENGTH(tx_info);
2762
2763 ret = sprintf(str, "State %s mult %d max P. Streams %d %s",
2764 xhci_ep_state_string(ep_state), mult,
2765 max_pstr, lsa ? "LSA " : "");
2766
2767 ret += sprintf(str + ret, "interval %d us max ESIT payload %d CErr %d ",
2768 (1 << interval) * 125, esit, cerr);
2769
2770 ret += sprintf(str + ret, "Type %s %sburst %d maxp %d deq %016llx ",
2771 xhci_ep_type_string(ep_type), hid ? "HID" : "",
2772 burst, maxp, deq);
2773
2774 ret += sprintf(str + ret, "avg trb len %d", avg);
2775
2776 return str;
2777 }
2778
2779 #endif /* __LINUX_XHCI_HCD_H */
2780