• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1 /* SPDX-License-Identifier: GPL-2.0-only */
2 /*
3  * linux/mdio.h: definitions for MDIO (clause 45) transceivers
4  * Copyright 2006-2009 Solarflare Communications Inc.
5  */
6 #ifndef __LINUX_MDIO_H__
7 #define __LINUX_MDIO_H__
8 
9 #include <uapi/linux/mdio.h>
10 #include <linux/mod_devicetable.h>
11 
12 /* Or MII_ADDR_C45 into regnum for read/write on mii_bus to enable the 21 bit
13  * IEEE 802.3ae clause 45 addressing mode used by 10GIGE phy chips.
14  */
15 #define MII_ADDR_C45		(1<<30)
16 #define MII_DEVADDR_C45_SHIFT	16
17 #define MII_REGADDR_C45_MASK	GENMASK(15, 0)
18 
19 struct gpio_desc;
20 struct mii_bus;
21 struct reset_control;
22 
23 /* Multiple levels of nesting are possible. However typically this is
24  * limited to nested DSA like layer, a MUX layer, and the normal
25  * user. Instead of trying to handle the general case, just define
26  * these cases.
27  */
28 enum mdio_mutex_lock_class {
29 	MDIO_MUTEX_NORMAL,
30 	MDIO_MUTEX_MUX,
31 	MDIO_MUTEX_NESTED,
32 };
33 
34 struct mdio_device {
35 	struct device dev;
36 
37 	struct mii_bus *bus;
38 	char modalias[MDIO_NAME_SIZE];
39 
40 	int (*bus_match)(struct device *dev, struct device_driver *drv);
41 	void (*device_free)(struct mdio_device *mdiodev);
42 	void (*device_remove)(struct mdio_device *mdiodev);
43 
44 	/* Bus address of the MDIO device (0-31) */
45 	int addr;
46 	int flags;
47 	struct gpio_desc *reset_gpio;
48 	struct reset_control *reset_ctrl;
49 	unsigned int reset_assert_delay;
50 	unsigned int reset_deassert_delay;
51 };
52 #define to_mdio_device(d) container_of(d, struct mdio_device, dev)
53 
54 /* struct mdio_driver_common: Common to all MDIO drivers */
55 struct mdio_driver_common {
56 	struct device_driver driver;
57 	int flags;
58 };
59 #define MDIO_DEVICE_FLAG_PHY		1
60 #define to_mdio_common_driver(d) \
61 	container_of(d, struct mdio_driver_common, driver)
62 
63 /* struct mdio_driver: Generic MDIO driver */
64 struct mdio_driver {
65 	struct mdio_driver_common mdiodrv;
66 
67 	/*
68 	 * Called during discovery.  Used to set
69 	 * up device-specific structures, if any
70 	 */
71 	int (*probe)(struct mdio_device *mdiodev);
72 
73 	/* Clears up any memory if needed */
74 	void (*remove)(struct mdio_device *mdiodev);
75 
76 	/* Quiesces the device on system shutdown, turns off interrupts etc */
77 	void (*shutdown)(struct mdio_device *mdiodev);
78 };
79 #define to_mdio_driver(d)						\
80 	container_of(to_mdio_common_driver(d), struct mdio_driver, mdiodrv)
81 
82 /* device driver data */
mdiodev_set_drvdata(struct mdio_device * mdio,void * data)83 static inline void mdiodev_set_drvdata(struct mdio_device *mdio, void *data)
84 {
85 	dev_set_drvdata(&mdio->dev, data);
86 }
87 
mdiodev_get_drvdata(struct mdio_device * mdio)88 static inline void *mdiodev_get_drvdata(struct mdio_device *mdio)
89 {
90 	return dev_get_drvdata(&mdio->dev);
91 }
92 
93 void mdio_device_free(struct mdio_device *mdiodev);
94 struct mdio_device *mdio_device_create(struct mii_bus *bus, int addr);
95 int mdio_device_register(struct mdio_device *mdiodev);
96 void mdio_device_remove(struct mdio_device *mdiodev);
97 void mdio_device_reset(struct mdio_device *mdiodev, int value);
98 int mdio_driver_register(struct mdio_driver *drv);
99 void mdio_driver_unregister(struct mdio_driver *drv);
100 int mdio_device_bus_match(struct device *dev, struct device_driver *drv);
101 
mdio_phy_id_is_c45(int phy_id)102 static inline bool mdio_phy_id_is_c45(int phy_id)
103 {
104 	return (phy_id & MDIO_PHY_ID_C45) && !(phy_id & ~MDIO_PHY_ID_C45_MASK);
105 }
106 
mdio_phy_id_prtad(int phy_id)107 static inline __u16 mdio_phy_id_prtad(int phy_id)
108 {
109 	return (phy_id & MDIO_PHY_ID_PRTAD) >> 5;
110 }
111 
mdio_phy_id_devad(int phy_id)112 static inline __u16 mdio_phy_id_devad(int phy_id)
113 {
114 	return phy_id & MDIO_PHY_ID_DEVAD;
115 }
116 
117 /**
118  * struct mdio_if_info - Ethernet controller MDIO interface
119  * @prtad: PRTAD of the PHY (%MDIO_PRTAD_NONE if not present/unknown)
120  * @mmds: Mask of MMDs expected to be present in the PHY.  This must be
121  *	non-zero unless @prtad = %MDIO_PRTAD_NONE.
122  * @mode_support: MDIO modes supported.  If %MDIO_SUPPORTS_C22 is set then
123  *	MII register access will be passed through with @devad =
124  *	%MDIO_DEVAD_NONE.  If %MDIO_EMULATE_C22 is set then access to
125  *	commonly used clause 22 registers will be translated into
126  *	clause 45 registers.
127  * @dev: Net device structure
128  * @mdio_read: Register read function; returns value or negative error code
129  * @mdio_write: Register write function; returns 0 or negative error code
130  */
131 struct mdio_if_info {
132 	int prtad;
133 	u32 mmds;
134 	unsigned mode_support;
135 
136 	struct net_device *dev;
137 	int (*mdio_read)(struct net_device *dev, int prtad, int devad,
138 			 u16 addr);
139 	int (*mdio_write)(struct net_device *dev, int prtad, int devad,
140 			  u16 addr, u16 val);
141 };
142 
143 #define MDIO_PRTAD_NONE			(-1)
144 #define MDIO_DEVAD_NONE			(-1)
145 #define MDIO_SUPPORTS_C22		1
146 #define MDIO_SUPPORTS_C45		2
147 #define MDIO_EMULATE_C22		4
148 
149 struct ethtool_cmd;
150 struct ethtool_pauseparam;
151 extern int mdio45_probe(struct mdio_if_info *mdio, int prtad);
152 extern int mdio_set_flag(const struct mdio_if_info *mdio,
153 			 int prtad, int devad, u16 addr, int mask,
154 			 bool sense);
155 extern int mdio45_links_ok(const struct mdio_if_info *mdio, u32 mmds);
156 extern int mdio45_nway_restart(const struct mdio_if_info *mdio);
157 extern void mdio45_ethtool_gset_npage(const struct mdio_if_info *mdio,
158 				      struct ethtool_cmd *ecmd,
159 				      u32 npage_adv, u32 npage_lpa);
160 extern void
161 mdio45_ethtool_ksettings_get_npage(const struct mdio_if_info *mdio,
162 				   struct ethtool_link_ksettings *cmd,
163 				   u32 npage_adv, u32 npage_lpa);
164 
165 /**
166  * mdio45_ethtool_gset - get settings for ETHTOOL_GSET
167  * @mdio: MDIO interface
168  * @ecmd: Ethtool request structure
169  *
170  * Since the CSRs for auto-negotiation using next pages are not fully
171  * standardised, this function does not attempt to decode them.  Use
172  * mdio45_ethtool_gset_npage() to specify advertisement bits from next
173  * pages.
174  */
mdio45_ethtool_gset(const struct mdio_if_info * mdio,struct ethtool_cmd * ecmd)175 static inline void mdio45_ethtool_gset(const struct mdio_if_info *mdio,
176 				       struct ethtool_cmd *ecmd)
177 {
178 	mdio45_ethtool_gset_npage(mdio, ecmd, 0, 0);
179 }
180 
181 /**
182  * mdio45_ethtool_ksettings_get - get settings for ETHTOOL_GLINKSETTINGS
183  * @mdio: MDIO interface
184  * @cmd: Ethtool request structure
185  *
186  * Since the CSRs for auto-negotiation using next pages are not fully
187  * standardised, this function does not attempt to decode them.  Use
188  * mdio45_ethtool_ksettings_get_npage() to specify advertisement bits
189  * from next pages.
190  */
191 static inline void
mdio45_ethtool_ksettings_get(const struct mdio_if_info * mdio,struct ethtool_link_ksettings * cmd)192 mdio45_ethtool_ksettings_get(const struct mdio_if_info *mdio,
193 			     struct ethtool_link_ksettings *cmd)
194 {
195 	mdio45_ethtool_ksettings_get_npage(mdio, cmd, 0, 0);
196 }
197 
198 extern int mdio_mii_ioctl(const struct mdio_if_info *mdio,
199 			  struct mii_ioctl_data *mii_data, int cmd);
200 
201 /**
202  * mmd_eee_cap_to_ethtool_sup_t
203  * @eee_cap: value of the MMD EEE Capability register
204  *
205  * A small helper function that translates MMD EEE Capability (3.20) bits
206  * to ethtool supported settings.
207  */
mmd_eee_cap_to_ethtool_sup_t(u16 eee_cap)208 static inline u32 mmd_eee_cap_to_ethtool_sup_t(u16 eee_cap)
209 {
210 	u32 supported = 0;
211 
212 	if (eee_cap & MDIO_EEE_100TX)
213 		supported |= SUPPORTED_100baseT_Full;
214 	if (eee_cap & MDIO_EEE_1000T)
215 		supported |= SUPPORTED_1000baseT_Full;
216 	if (eee_cap & MDIO_EEE_10GT)
217 		supported |= SUPPORTED_10000baseT_Full;
218 	if (eee_cap & MDIO_EEE_1000KX)
219 		supported |= SUPPORTED_1000baseKX_Full;
220 	if (eee_cap & MDIO_EEE_10GKX4)
221 		supported |= SUPPORTED_10000baseKX4_Full;
222 	if (eee_cap & MDIO_EEE_10GKR)
223 		supported |= SUPPORTED_10000baseKR_Full;
224 
225 	return supported;
226 }
227 
228 /**
229  * mmd_eee_adv_to_ethtool_adv_t
230  * @eee_adv: value of the MMD EEE Advertisement/Link Partner Ability registers
231  *
232  * A small helper function that translates the MMD EEE Advertisment (7.60)
233  * and MMD EEE Link Partner Ability (7.61) bits to ethtool advertisement
234  * settings.
235  */
mmd_eee_adv_to_ethtool_adv_t(u16 eee_adv)236 static inline u32 mmd_eee_adv_to_ethtool_adv_t(u16 eee_adv)
237 {
238 	u32 adv = 0;
239 
240 	if (eee_adv & MDIO_EEE_100TX)
241 		adv |= ADVERTISED_100baseT_Full;
242 	if (eee_adv & MDIO_EEE_1000T)
243 		adv |= ADVERTISED_1000baseT_Full;
244 	if (eee_adv & MDIO_EEE_10GT)
245 		adv |= ADVERTISED_10000baseT_Full;
246 	if (eee_adv & MDIO_EEE_1000KX)
247 		adv |= ADVERTISED_1000baseKX_Full;
248 	if (eee_adv & MDIO_EEE_10GKX4)
249 		adv |= ADVERTISED_10000baseKX4_Full;
250 	if (eee_adv & MDIO_EEE_10GKR)
251 		adv |= ADVERTISED_10000baseKR_Full;
252 
253 	return adv;
254 }
255 
256 /**
257  * ethtool_adv_to_mmd_eee_adv_t
258  * @adv: the ethtool advertisement settings
259  *
260  * A small helper function that translates ethtool advertisement settings
261  * to EEE advertisements for the MMD EEE Advertisement (7.60) and
262  * MMD EEE Link Partner Ability (7.61) registers.
263  */
ethtool_adv_to_mmd_eee_adv_t(u32 adv)264 static inline u16 ethtool_adv_to_mmd_eee_adv_t(u32 adv)
265 {
266 	u16 reg = 0;
267 
268 	if (adv & ADVERTISED_100baseT_Full)
269 		reg |= MDIO_EEE_100TX;
270 	if (adv & ADVERTISED_1000baseT_Full)
271 		reg |= MDIO_EEE_1000T;
272 	if (adv & ADVERTISED_10000baseT_Full)
273 		reg |= MDIO_EEE_10GT;
274 	if (adv & ADVERTISED_1000baseKX_Full)
275 		reg |= MDIO_EEE_1000KX;
276 	if (adv & ADVERTISED_10000baseKX4_Full)
277 		reg |= MDIO_EEE_10GKX4;
278 	if (adv & ADVERTISED_10000baseKR_Full)
279 		reg |= MDIO_EEE_10GKR;
280 
281 	return reg;
282 }
283 
284 /**
285  * linkmode_adv_to_mii_10gbt_adv_t
286  * @advertising: the linkmode advertisement settings
287  *
288  * A small helper function that translates linkmode advertisement
289  * settings to phy autonegotiation advertisements for the C45
290  * 10GBASE-T AN CONTROL (7.32) register.
291  */
linkmode_adv_to_mii_10gbt_adv_t(unsigned long * advertising)292 static inline u32 linkmode_adv_to_mii_10gbt_adv_t(unsigned long *advertising)
293 {
294 	u32 result = 0;
295 
296 	if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT,
297 			      advertising))
298 		result |= MDIO_AN_10GBT_CTRL_ADV2_5G;
299 	if (linkmode_test_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT,
300 			      advertising))
301 		result |= MDIO_AN_10GBT_CTRL_ADV5G;
302 	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
303 			      advertising))
304 		result |= MDIO_AN_10GBT_CTRL_ADV10G;
305 
306 	return result;
307 }
308 
309 /**
310  * mii_10gbt_stat_mod_linkmode_lpa_t
311  * @advertising: target the linkmode advertisement settings
312  * @lpa: value of the C45 10GBASE-T AN STATUS register
313  *
314  * A small helper function that translates C45 10GBASE-T AN STATUS register bits
315  * to linkmode advertisement settings. Other bits in advertising aren't changed.
316  */
mii_10gbt_stat_mod_linkmode_lpa_t(unsigned long * advertising,u32 lpa)317 static inline void mii_10gbt_stat_mod_linkmode_lpa_t(unsigned long *advertising,
318 						     u32 lpa)
319 {
320 	linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT,
321 			 advertising, lpa & MDIO_AN_10GBT_STAT_LP2_5G);
322 	linkmode_mod_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT,
323 			 advertising, lpa & MDIO_AN_10GBT_STAT_LP5G);
324 	linkmode_mod_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
325 			 advertising, lpa & MDIO_AN_10GBT_STAT_LP10G);
326 }
327 
328 int __mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
329 int __mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
330 int __mdiobus_modify_changed(struct mii_bus *bus, int addr, u32 regnum,
331 			     u16 mask, u16 set);
332 
333 int mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
334 int mdiobus_read_nested(struct mii_bus *bus, int addr, u32 regnum);
335 int mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
336 int mdiobus_write_nested(struct mii_bus *bus, int addr, u32 regnum, u16 val);
337 int mdiobus_modify(struct mii_bus *bus, int addr, u32 regnum, u16 mask,
338 		   u16 set);
339 
mdiobus_c45_addr(int devad,u16 regnum)340 static inline u32 mdiobus_c45_addr(int devad, u16 regnum)
341 {
342 	return MII_ADDR_C45 | devad << MII_DEVADDR_C45_SHIFT | regnum;
343 }
344 
__mdiobus_c45_read(struct mii_bus * bus,int prtad,int devad,u16 regnum)345 static inline int __mdiobus_c45_read(struct mii_bus *bus, int prtad, int devad,
346 				     u16 regnum)
347 {
348 	return __mdiobus_read(bus, prtad, mdiobus_c45_addr(devad, regnum));
349 }
350 
__mdiobus_c45_write(struct mii_bus * bus,int prtad,int devad,u16 regnum,u16 val)351 static inline int __mdiobus_c45_write(struct mii_bus *bus, int prtad, int devad,
352 				      u16 regnum, u16 val)
353 {
354 	return __mdiobus_write(bus, prtad, mdiobus_c45_addr(devad, regnum),
355 			       val);
356 }
357 
mdiobus_c45_read(struct mii_bus * bus,int prtad,int devad,u16 regnum)358 static inline int mdiobus_c45_read(struct mii_bus *bus, int prtad, int devad,
359 				   u16 regnum)
360 {
361 	return mdiobus_read(bus, prtad, mdiobus_c45_addr(devad, regnum));
362 }
363 
mdiobus_c45_write(struct mii_bus * bus,int prtad,int devad,u16 regnum,u16 val)364 static inline int mdiobus_c45_write(struct mii_bus *bus, int prtad, int devad,
365 				    u16 regnum, u16 val)
366 {
367 	return mdiobus_write(bus, prtad, mdiobus_c45_addr(devad, regnum), val);
368 }
369 
370 int mdiobus_register_device(struct mdio_device *mdiodev);
371 int mdiobus_unregister_device(struct mdio_device *mdiodev);
372 bool mdiobus_is_registered_device(struct mii_bus *bus, int addr);
373 struct phy_device *mdiobus_get_phy(struct mii_bus *bus, int addr);
374 
375 /**
376  * mdio_module_driver() - Helper macro for registering mdio drivers
377  * @_mdio_driver: driver to register
378  *
379  * Helper macro for MDIO drivers which do not do anything special in module
380  * init/exit. Each module may only use this macro once, and calling it
381  * replaces module_init() and module_exit().
382  */
383 #define mdio_module_driver(_mdio_driver)				\
384 static int __init mdio_module_init(void)				\
385 {									\
386 	return mdio_driver_register(&_mdio_driver);			\
387 }									\
388 module_init(mdio_module_init);						\
389 static void __exit mdio_module_exit(void)				\
390 {									\
391 	mdio_driver_unregister(&_mdio_driver);				\
392 }									\
393 module_exit(mdio_module_exit)
394 
395 #endif /* __LINUX_MDIO_H__ */
396