1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 Copyright (C) 2010 Willow Garage <http://www.willowgarage.com>
4 Copyright (C) 2004 - 2010 Ivo van Doorn <IvDoorn@gmail.com>
5 <http://rt2x00.serialmonkey.com>
6
7 */
8
9 /*
10 Module: rt2x00lib
11 Abstract: rt2x00 generic device routines.
12 */
13
14 #include <linux/kernel.h>
15 #include <linux/module.h>
16 #include <linux/slab.h>
17 #include <linux/log2.h>
18 #include <linux/of.h>
19 #include <linux/of_net.h>
20
21 #include "rt2x00.h"
22 #include "rt2x00lib.h"
23
24 /*
25 * Utility functions.
26 */
rt2x00lib_get_bssidx(struct rt2x00_dev * rt2x00dev,struct ieee80211_vif * vif)27 u32 rt2x00lib_get_bssidx(struct rt2x00_dev *rt2x00dev,
28 struct ieee80211_vif *vif)
29 {
30 /*
31 * When in STA mode, bssidx is always 0 otherwise local_address[5]
32 * contains the bss number, see BSS_ID_MASK comments for details.
33 */
34 if (rt2x00dev->intf_sta_count)
35 return 0;
36 return vif->addr[5] & (rt2x00dev->ops->max_ap_intf - 1);
37 }
38 EXPORT_SYMBOL_GPL(rt2x00lib_get_bssidx);
39
40 /*
41 * Radio control handlers.
42 */
rt2x00lib_enable_radio(struct rt2x00_dev * rt2x00dev)43 int rt2x00lib_enable_radio(struct rt2x00_dev *rt2x00dev)
44 {
45 int status;
46
47 /*
48 * Don't enable the radio twice.
49 * And check if the hardware button has been disabled.
50 */
51 if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
52 return 0;
53
54 /*
55 * Initialize all data queues.
56 */
57 rt2x00queue_init_queues(rt2x00dev);
58
59 /*
60 * Enable radio.
61 */
62 status =
63 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_ON);
64 if (status)
65 return status;
66
67 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_IRQ_ON);
68
69 rt2x00leds_led_radio(rt2x00dev, true);
70 rt2x00led_led_activity(rt2x00dev, true);
71
72 set_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags);
73
74 /*
75 * Enable queues.
76 */
77 rt2x00queue_start_queues(rt2x00dev);
78 rt2x00link_start_tuner(rt2x00dev);
79
80 /*
81 * Start watchdog monitoring.
82 */
83 rt2x00link_start_watchdog(rt2x00dev);
84
85 return 0;
86 }
87
rt2x00lib_disable_radio(struct rt2x00_dev * rt2x00dev)88 void rt2x00lib_disable_radio(struct rt2x00_dev *rt2x00dev)
89 {
90 if (!test_and_clear_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
91 return;
92
93 /*
94 * Stop watchdog monitoring.
95 */
96 rt2x00link_stop_watchdog(rt2x00dev);
97
98 /*
99 * Stop all queues
100 */
101 rt2x00link_stop_tuner(rt2x00dev);
102 rt2x00queue_stop_queues(rt2x00dev);
103 rt2x00queue_flush_queues(rt2x00dev, true);
104
105 /*
106 * Disable radio.
107 */
108 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_OFF);
109 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_IRQ_OFF);
110 rt2x00led_led_activity(rt2x00dev, false);
111 rt2x00leds_led_radio(rt2x00dev, false);
112 }
113
rt2x00lib_intf_scheduled_iter(void * data,u8 * mac,struct ieee80211_vif * vif)114 static void rt2x00lib_intf_scheduled_iter(void *data, u8 *mac,
115 struct ieee80211_vif *vif)
116 {
117 struct rt2x00_dev *rt2x00dev = data;
118 struct rt2x00_intf *intf = vif_to_intf(vif);
119
120 /*
121 * It is possible the radio was disabled while the work had been
122 * scheduled. If that happens we should return here immediately,
123 * note that in the spinlock protected area above the delayed_flags
124 * have been cleared correctly.
125 */
126 if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
127 return;
128
129 if (test_and_clear_bit(DELAYED_UPDATE_BEACON, &intf->delayed_flags)) {
130 mutex_lock(&intf->beacon_skb_mutex);
131 rt2x00queue_update_beacon(rt2x00dev, vif);
132 mutex_unlock(&intf->beacon_skb_mutex);
133 }
134 }
135
rt2x00lib_intf_scheduled(struct work_struct * work)136 static void rt2x00lib_intf_scheduled(struct work_struct *work)
137 {
138 struct rt2x00_dev *rt2x00dev =
139 container_of(work, struct rt2x00_dev, intf_work);
140
141 /*
142 * Iterate over each interface and perform the
143 * requested configurations.
144 */
145 ieee80211_iterate_active_interfaces(rt2x00dev->hw,
146 IEEE80211_IFACE_ITER_RESUME_ALL,
147 rt2x00lib_intf_scheduled_iter,
148 rt2x00dev);
149 }
150
rt2x00lib_autowakeup(struct work_struct * work)151 static void rt2x00lib_autowakeup(struct work_struct *work)
152 {
153 struct rt2x00_dev *rt2x00dev =
154 container_of(work, struct rt2x00_dev, autowakeup_work.work);
155
156 if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
157 return;
158
159 if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE))
160 rt2x00_err(rt2x00dev, "Device failed to wakeup\n");
161 clear_bit(CONFIG_POWERSAVING, &rt2x00dev->flags);
162 }
163
164 /*
165 * Interrupt context handlers.
166 */
rt2x00lib_bc_buffer_iter(void * data,u8 * mac,struct ieee80211_vif * vif)167 static void rt2x00lib_bc_buffer_iter(void *data, u8 *mac,
168 struct ieee80211_vif *vif)
169 {
170 struct ieee80211_tx_control control = {};
171 struct rt2x00_dev *rt2x00dev = data;
172 struct sk_buff *skb;
173
174 /*
175 * Only AP mode interfaces do broad- and multicast buffering
176 */
177 if (vif->type != NL80211_IFTYPE_AP)
178 return;
179
180 /*
181 * Send out buffered broad- and multicast frames
182 */
183 skb = ieee80211_get_buffered_bc(rt2x00dev->hw, vif);
184 while (skb) {
185 rt2x00mac_tx(rt2x00dev->hw, &control, skb);
186 skb = ieee80211_get_buffered_bc(rt2x00dev->hw, vif);
187 }
188 }
189
rt2x00lib_beaconupdate_iter(void * data,u8 * mac,struct ieee80211_vif * vif)190 static void rt2x00lib_beaconupdate_iter(void *data, u8 *mac,
191 struct ieee80211_vif *vif)
192 {
193 struct rt2x00_dev *rt2x00dev = data;
194
195 if (vif->type != NL80211_IFTYPE_AP &&
196 vif->type != NL80211_IFTYPE_ADHOC &&
197 vif->type != NL80211_IFTYPE_MESH_POINT &&
198 vif->type != NL80211_IFTYPE_WDS)
199 return;
200
201 /*
202 * Update the beacon without locking. This is safe on PCI devices
203 * as they only update the beacon periodically here. This should
204 * never be called for USB devices.
205 */
206 WARN_ON(rt2x00_is_usb(rt2x00dev));
207 rt2x00queue_update_beacon(rt2x00dev, vif);
208 }
209
rt2x00lib_beacondone(struct rt2x00_dev * rt2x00dev)210 void rt2x00lib_beacondone(struct rt2x00_dev *rt2x00dev)
211 {
212 if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
213 return;
214
215 /* send buffered bc/mc frames out for every bssid */
216 ieee80211_iterate_active_interfaces_atomic(
217 rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
218 rt2x00lib_bc_buffer_iter, rt2x00dev);
219 /*
220 * Devices with pre tbtt interrupt don't need to update the beacon
221 * here as they will fetch the next beacon directly prior to
222 * transmission.
223 */
224 if (rt2x00_has_cap_pre_tbtt_interrupt(rt2x00dev))
225 return;
226
227 /* fetch next beacon */
228 ieee80211_iterate_active_interfaces_atomic(
229 rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
230 rt2x00lib_beaconupdate_iter, rt2x00dev);
231 }
232 EXPORT_SYMBOL_GPL(rt2x00lib_beacondone);
233
rt2x00lib_pretbtt(struct rt2x00_dev * rt2x00dev)234 void rt2x00lib_pretbtt(struct rt2x00_dev *rt2x00dev)
235 {
236 if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
237 return;
238
239 /* fetch next beacon */
240 ieee80211_iterate_active_interfaces_atomic(
241 rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
242 rt2x00lib_beaconupdate_iter, rt2x00dev);
243 }
244 EXPORT_SYMBOL_GPL(rt2x00lib_pretbtt);
245
rt2x00lib_dmastart(struct queue_entry * entry)246 void rt2x00lib_dmastart(struct queue_entry *entry)
247 {
248 set_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
249 rt2x00queue_index_inc(entry, Q_INDEX);
250 }
251 EXPORT_SYMBOL_GPL(rt2x00lib_dmastart);
252
rt2x00lib_dmadone(struct queue_entry * entry)253 void rt2x00lib_dmadone(struct queue_entry *entry)
254 {
255 set_bit(ENTRY_DATA_STATUS_PENDING, &entry->flags);
256 clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
257 rt2x00queue_index_inc(entry, Q_INDEX_DMA_DONE);
258 }
259 EXPORT_SYMBOL_GPL(rt2x00lib_dmadone);
260
rt2x00lib_txdone_bar_status(struct queue_entry * entry)261 static inline int rt2x00lib_txdone_bar_status(struct queue_entry *entry)
262 {
263 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
264 struct ieee80211_bar *bar = (void *) entry->skb->data;
265 struct rt2x00_bar_list_entry *bar_entry;
266 int ret;
267
268 if (likely(!ieee80211_is_back_req(bar->frame_control)))
269 return 0;
270
271 /*
272 * Unlike all other frames, the status report for BARs does
273 * not directly come from the hardware as it is incapable of
274 * matching a BA to a previously send BAR. The hardware will
275 * report all BARs as if they weren't acked at all.
276 *
277 * Instead the RX-path will scan for incoming BAs and set the
278 * block_acked flag if it sees one that was likely caused by
279 * a BAR from us.
280 *
281 * Remove remaining BARs here and return their status for
282 * TX done processing.
283 */
284 ret = 0;
285 rcu_read_lock();
286 list_for_each_entry_rcu(bar_entry, &rt2x00dev->bar_list, list) {
287 if (bar_entry->entry != entry)
288 continue;
289
290 spin_lock_bh(&rt2x00dev->bar_list_lock);
291 /* Return whether this BAR was blockacked or not */
292 ret = bar_entry->block_acked;
293 /* Remove the BAR from our checklist */
294 list_del_rcu(&bar_entry->list);
295 spin_unlock_bh(&rt2x00dev->bar_list_lock);
296 kfree_rcu(bar_entry, head);
297
298 break;
299 }
300 rcu_read_unlock();
301
302 return ret;
303 }
304
rt2x00lib_fill_tx_status(struct rt2x00_dev * rt2x00dev,struct ieee80211_tx_info * tx_info,struct skb_frame_desc * skbdesc,struct txdone_entry_desc * txdesc,bool success)305 static void rt2x00lib_fill_tx_status(struct rt2x00_dev *rt2x00dev,
306 struct ieee80211_tx_info *tx_info,
307 struct skb_frame_desc *skbdesc,
308 struct txdone_entry_desc *txdesc,
309 bool success)
310 {
311 u8 rate_idx, rate_flags, retry_rates;
312 int i;
313
314 rate_idx = skbdesc->tx_rate_idx;
315 rate_flags = skbdesc->tx_rate_flags;
316 retry_rates = test_bit(TXDONE_FALLBACK, &txdesc->flags) ?
317 (txdesc->retry + 1) : 1;
318
319 /*
320 * Initialize TX status
321 */
322 memset(&tx_info->status, 0, sizeof(tx_info->status));
323 tx_info->status.ack_signal = 0;
324
325 /*
326 * Frame was send with retries, hardware tried
327 * different rates to send out the frame, at each
328 * retry it lowered the rate 1 step except when the
329 * lowest rate was used.
330 */
331 for (i = 0; i < retry_rates && i < IEEE80211_TX_MAX_RATES; i++) {
332 tx_info->status.rates[i].idx = rate_idx - i;
333 tx_info->status.rates[i].flags = rate_flags;
334
335 if (rate_idx - i == 0) {
336 /*
337 * The lowest rate (index 0) was used until the
338 * number of max retries was reached.
339 */
340 tx_info->status.rates[i].count = retry_rates - i;
341 i++;
342 break;
343 }
344 tx_info->status.rates[i].count = 1;
345 }
346 if (i < (IEEE80211_TX_MAX_RATES - 1))
347 tx_info->status.rates[i].idx = -1; /* terminate */
348
349 if (test_bit(TXDONE_NO_ACK_REQ, &txdesc->flags))
350 tx_info->flags |= IEEE80211_TX_CTL_NO_ACK;
351
352 if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) {
353 if (success)
354 tx_info->flags |= IEEE80211_TX_STAT_ACK;
355 else
356 rt2x00dev->low_level_stats.dot11ACKFailureCount++;
357 }
358
359 /*
360 * Every single frame has it's own tx status, hence report
361 * every frame as ampdu of size 1.
362 *
363 * TODO: if we can find out how many frames were aggregated
364 * by the hw we could provide the real ampdu_len to mac80211
365 * which would allow the rc algorithm to better decide on
366 * which rates are suitable.
367 */
368 if (test_bit(TXDONE_AMPDU, &txdesc->flags) ||
369 tx_info->flags & IEEE80211_TX_CTL_AMPDU) {
370 tx_info->flags |= IEEE80211_TX_STAT_AMPDU |
371 IEEE80211_TX_CTL_AMPDU;
372 tx_info->status.ampdu_len = 1;
373 tx_info->status.ampdu_ack_len = success ? 1 : 0;
374 }
375
376 if (rate_flags & IEEE80211_TX_RC_USE_RTS_CTS) {
377 if (success)
378 rt2x00dev->low_level_stats.dot11RTSSuccessCount++;
379 else
380 rt2x00dev->low_level_stats.dot11RTSFailureCount++;
381 }
382 }
383
rt2x00lib_clear_entry(struct rt2x00_dev * rt2x00dev,struct queue_entry * entry)384 static void rt2x00lib_clear_entry(struct rt2x00_dev *rt2x00dev,
385 struct queue_entry *entry)
386 {
387 /*
388 * Make this entry available for reuse.
389 */
390 entry->skb = NULL;
391 entry->flags = 0;
392
393 rt2x00dev->ops->lib->clear_entry(entry);
394
395 rt2x00queue_index_inc(entry, Q_INDEX_DONE);
396
397 /*
398 * If the data queue was below the threshold before the txdone
399 * handler we must make sure the packet queue in the mac80211 stack
400 * is reenabled when the txdone handler has finished. This has to be
401 * serialized with rt2x00mac_tx(), otherwise we can wake up queue
402 * before it was stopped.
403 */
404 spin_lock_bh(&entry->queue->tx_lock);
405 if (!rt2x00queue_threshold(entry->queue))
406 rt2x00queue_unpause_queue(entry->queue);
407 spin_unlock_bh(&entry->queue->tx_lock);
408 }
409
rt2x00lib_txdone_nomatch(struct queue_entry * entry,struct txdone_entry_desc * txdesc)410 void rt2x00lib_txdone_nomatch(struct queue_entry *entry,
411 struct txdone_entry_desc *txdesc)
412 {
413 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
414 struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
415 struct ieee80211_tx_info txinfo = {};
416 bool success;
417
418 /*
419 * Unmap the skb.
420 */
421 rt2x00queue_unmap_skb(entry);
422
423 /*
424 * Signal that the TX descriptor is no longer in the skb.
425 */
426 skbdesc->flags &= ~SKBDESC_DESC_IN_SKB;
427
428 /*
429 * Send frame to debugfs immediately, after this call is completed
430 * we are going to overwrite the skb->cb array.
431 */
432 rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry);
433
434 /*
435 * Determine if the frame has been successfully transmitted and
436 * remove BARs from our check list while checking for their
437 * TX status.
438 */
439 success =
440 rt2x00lib_txdone_bar_status(entry) ||
441 test_bit(TXDONE_SUCCESS, &txdesc->flags);
442
443 if (!test_bit(TXDONE_UNKNOWN, &txdesc->flags)) {
444 /*
445 * Update TX statistics.
446 */
447 rt2x00dev->link.qual.tx_success += success;
448 rt2x00dev->link.qual.tx_failed += !success;
449
450 rt2x00lib_fill_tx_status(rt2x00dev, &txinfo, skbdesc, txdesc,
451 success);
452 ieee80211_tx_status_noskb(rt2x00dev->hw, skbdesc->sta, &txinfo);
453 }
454
455 dev_kfree_skb_any(entry->skb);
456 rt2x00lib_clear_entry(rt2x00dev, entry);
457 }
458 EXPORT_SYMBOL_GPL(rt2x00lib_txdone_nomatch);
459
rt2x00lib_txdone(struct queue_entry * entry,struct txdone_entry_desc * txdesc)460 void rt2x00lib_txdone(struct queue_entry *entry,
461 struct txdone_entry_desc *txdesc)
462 {
463 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
464 struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
465 struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
466 u8 skbdesc_flags = skbdesc->flags;
467 unsigned int header_length;
468 bool success;
469
470 /*
471 * Unmap the skb.
472 */
473 rt2x00queue_unmap_skb(entry);
474
475 /*
476 * Remove the extra tx headroom from the skb.
477 */
478 skb_pull(entry->skb, rt2x00dev->extra_tx_headroom);
479
480 /*
481 * Signal that the TX descriptor is no longer in the skb.
482 */
483 skbdesc->flags &= ~SKBDESC_DESC_IN_SKB;
484
485 /*
486 * Determine the length of 802.11 header.
487 */
488 header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
489
490 /*
491 * Remove L2 padding which was added during
492 */
493 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_L2PAD))
494 rt2x00queue_remove_l2pad(entry->skb, header_length);
495
496 /*
497 * If the IV/EIV data was stripped from the frame before it was
498 * passed to the hardware, we should now reinsert it again because
499 * mac80211 will expect the same data to be present it the
500 * frame as it was passed to us.
501 */
502 if (rt2x00_has_cap_hw_crypto(rt2x00dev))
503 rt2x00crypto_tx_insert_iv(entry->skb, header_length);
504
505 /*
506 * Send frame to debugfs immediately, after this call is completed
507 * we are going to overwrite the skb->cb array.
508 */
509 rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry);
510
511 /*
512 * Determine if the frame has been successfully transmitted and
513 * remove BARs from our check list while checking for their
514 * TX status.
515 */
516 success =
517 rt2x00lib_txdone_bar_status(entry) ||
518 test_bit(TXDONE_SUCCESS, &txdesc->flags) ||
519 test_bit(TXDONE_UNKNOWN, &txdesc->flags);
520
521 /*
522 * Update TX statistics.
523 */
524 rt2x00dev->link.qual.tx_success += success;
525 rt2x00dev->link.qual.tx_failed += !success;
526
527 rt2x00lib_fill_tx_status(rt2x00dev, tx_info, skbdesc, txdesc, success);
528
529 /*
530 * Only send the status report to mac80211 when it's a frame
531 * that originated in mac80211. If this was a extra frame coming
532 * through a mac80211 library call (RTS/CTS) then we should not
533 * send the status report back.
534 */
535 if (!(skbdesc_flags & SKBDESC_NOT_MAC80211)) {
536 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_TASKLET_CONTEXT))
537 ieee80211_tx_status(rt2x00dev->hw, entry->skb);
538 else
539 ieee80211_tx_status_ni(rt2x00dev->hw, entry->skb);
540 } else {
541 dev_kfree_skb_any(entry->skb);
542 }
543
544 rt2x00lib_clear_entry(rt2x00dev, entry);
545 }
546 EXPORT_SYMBOL_GPL(rt2x00lib_txdone);
547
rt2x00lib_txdone_noinfo(struct queue_entry * entry,u32 status)548 void rt2x00lib_txdone_noinfo(struct queue_entry *entry, u32 status)
549 {
550 struct txdone_entry_desc txdesc;
551
552 txdesc.flags = 0;
553 __set_bit(status, &txdesc.flags);
554 txdesc.retry = 0;
555
556 rt2x00lib_txdone(entry, &txdesc);
557 }
558 EXPORT_SYMBOL_GPL(rt2x00lib_txdone_noinfo);
559
rt2x00lib_find_ie(u8 * data,unsigned int len,u8 ie)560 static u8 *rt2x00lib_find_ie(u8 *data, unsigned int len, u8 ie)
561 {
562 struct ieee80211_mgmt *mgmt = (void *)data;
563 u8 *pos, *end;
564
565 pos = (u8 *)mgmt->u.beacon.variable;
566 end = data + len;
567 while (pos < end) {
568 if (pos + 2 + pos[1] > end)
569 return NULL;
570
571 if (pos[0] == ie)
572 return pos;
573
574 pos += 2 + pos[1];
575 }
576
577 return NULL;
578 }
579
rt2x00lib_sleep(struct work_struct * work)580 static void rt2x00lib_sleep(struct work_struct *work)
581 {
582 struct rt2x00_dev *rt2x00dev =
583 container_of(work, struct rt2x00_dev, sleep_work);
584
585 if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
586 return;
587
588 /*
589 * Check again is powersaving is enabled, to prevent races from delayed
590 * work execution.
591 */
592 if (!test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags))
593 rt2x00lib_config(rt2x00dev, &rt2x00dev->hw->conf,
594 IEEE80211_CONF_CHANGE_PS);
595 }
596
rt2x00lib_rxdone_check_ba(struct rt2x00_dev * rt2x00dev,struct sk_buff * skb,struct rxdone_entry_desc * rxdesc)597 static void rt2x00lib_rxdone_check_ba(struct rt2x00_dev *rt2x00dev,
598 struct sk_buff *skb,
599 struct rxdone_entry_desc *rxdesc)
600 {
601 struct rt2x00_bar_list_entry *entry;
602 struct ieee80211_bar *ba = (void *)skb->data;
603
604 if (likely(!ieee80211_is_back(ba->frame_control)))
605 return;
606
607 if (rxdesc->size < sizeof(*ba) + FCS_LEN)
608 return;
609
610 rcu_read_lock();
611 list_for_each_entry_rcu(entry, &rt2x00dev->bar_list, list) {
612
613 if (ba->start_seq_num != entry->start_seq_num)
614 continue;
615
616 #define TID_CHECK(a, b) ( \
617 ((a) & cpu_to_le16(IEEE80211_BAR_CTRL_TID_INFO_MASK)) == \
618 ((b) & cpu_to_le16(IEEE80211_BAR_CTRL_TID_INFO_MASK))) \
619
620 if (!TID_CHECK(ba->control, entry->control))
621 continue;
622
623 #undef TID_CHECK
624
625 if (!ether_addr_equal_64bits(ba->ra, entry->ta))
626 continue;
627
628 if (!ether_addr_equal_64bits(ba->ta, entry->ra))
629 continue;
630
631 /* Mark BAR since we received the according BA */
632 spin_lock_bh(&rt2x00dev->bar_list_lock);
633 entry->block_acked = 1;
634 spin_unlock_bh(&rt2x00dev->bar_list_lock);
635 break;
636 }
637 rcu_read_unlock();
638
639 }
640
rt2x00lib_rxdone_check_ps(struct rt2x00_dev * rt2x00dev,struct sk_buff * skb,struct rxdone_entry_desc * rxdesc)641 static void rt2x00lib_rxdone_check_ps(struct rt2x00_dev *rt2x00dev,
642 struct sk_buff *skb,
643 struct rxdone_entry_desc *rxdesc)
644 {
645 struct ieee80211_hdr *hdr = (void *) skb->data;
646 struct ieee80211_tim_ie *tim_ie;
647 u8 *tim;
648 u8 tim_len;
649 bool cam;
650
651 /* If this is not a beacon, or if mac80211 has no powersaving
652 * configured, or if the device is already in powersaving mode
653 * we can exit now. */
654 if (likely(!ieee80211_is_beacon(hdr->frame_control) ||
655 !(rt2x00dev->hw->conf.flags & IEEE80211_CONF_PS)))
656 return;
657
658 /* min. beacon length + FCS_LEN */
659 if (skb->len <= 40 + FCS_LEN)
660 return;
661
662 /* and only beacons from the associated BSSID, please */
663 if (!(rxdesc->dev_flags & RXDONE_MY_BSS) ||
664 !rt2x00dev->aid)
665 return;
666
667 rt2x00dev->last_beacon = jiffies;
668
669 tim = rt2x00lib_find_ie(skb->data, skb->len - FCS_LEN, WLAN_EID_TIM);
670 if (!tim)
671 return;
672
673 if (tim[1] < sizeof(*tim_ie))
674 return;
675
676 tim_len = tim[1];
677 tim_ie = (struct ieee80211_tim_ie *) &tim[2];
678
679 /* Check whenever the PHY can be turned off again. */
680
681 /* 1. What about buffered unicast traffic for our AID? */
682 cam = ieee80211_check_tim(tim_ie, tim_len, rt2x00dev->aid);
683
684 /* 2. Maybe the AP wants to send multicast/broadcast data? */
685 cam |= (tim_ie->bitmap_ctrl & 0x01);
686
687 if (!cam && !test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags))
688 queue_work(rt2x00dev->workqueue, &rt2x00dev->sleep_work);
689 }
690
rt2x00lib_rxdone_read_signal(struct rt2x00_dev * rt2x00dev,struct rxdone_entry_desc * rxdesc)691 static int rt2x00lib_rxdone_read_signal(struct rt2x00_dev *rt2x00dev,
692 struct rxdone_entry_desc *rxdesc)
693 {
694 struct ieee80211_supported_band *sband;
695 const struct rt2x00_rate *rate;
696 unsigned int i;
697 int signal = rxdesc->signal;
698 int type = (rxdesc->dev_flags & RXDONE_SIGNAL_MASK);
699
700 switch (rxdesc->rate_mode) {
701 case RATE_MODE_CCK:
702 case RATE_MODE_OFDM:
703 /*
704 * For non-HT rates the MCS value needs to contain the
705 * actually used rate modulation (CCK or OFDM).
706 */
707 if (rxdesc->dev_flags & RXDONE_SIGNAL_MCS)
708 signal = RATE_MCS(rxdesc->rate_mode, signal);
709
710 sband = &rt2x00dev->bands[rt2x00dev->curr_band];
711 for (i = 0; i < sband->n_bitrates; i++) {
712 rate = rt2x00_get_rate(sband->bitrates[i].hw_value);
713 if (((type == RXDONE_SIGNAL_PLCP) &&
714 (rate->plcp == signal)) ||
715 ((type == RXDONE_SIGNAL_BITRATE) &&
716 (rate->bitrate == signal)) ||
717 ((type == RXDONE_SIGNAL_MCS) &&
718 (rate->mcs == signal))) {
719 return i;
720 }
721 }
722 break;
723 case RATE_MODE_HT_MIX:
724 case RATE_MODE_HT_GREENFIELD:
725 if (signal >= 0 && signal <= 76)
726 return signal;
727 break;
728 default:
729 break;
730 }
731
732 rt2x00_warn(rt2x00dev, "Frame received with unrecognized signal, mode=0x%.4x, signal=0x%.4x, type=%d\n",
733 rxdesc->rate_mode, signal, type);
734 return 0;
735 }
736
rt2x00lib_rxdone(struct queue_entry * entry,gfp_t gfp)737 void rt2x00lib_rxdone(struct queue_entry *entry, gfp_t gfp)
738 {
739 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
740 struct rxdone_entry_desc rxdesc;
741 struct sk_buff *skb;
742 struct ieee80211_rx_status *rx_status;
743 unsigned int header_length;
744 int rate_idx;
745
746 if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) ||
747 !test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
748 goto submit_entry;
749
750 if (test_bit(ENTRY_DATA_IO_FAILED, &entry->flags))
751 goto submit_entry;
752
753 /*
754 * Allocate a new sk_buffer. If no new buffer available, drop the
755 * received frame and reuse the existing buffer.
756 */
757 skb = rt2x00queue_alloc_rxskb(entry, gfp);
758 if (!skb)
759 goto submit_entry;
760
761 /*
762 * Unmap the skb.
763 */
764 rt2x00queue_unmap_skb(entry);
765
766 /*
767 * Extract the RXD details.
768 */
769 memset(&rxdesc, 0, sizeof(rxdesc));
770 rt2x00dev->ops->lib->fill_rxdone(entry, &rxdesc);
771
772 /*
773 * Check for valid size in case we get corrupted descriptor from
774 * hardware.
775 */
776 if (unlikely(rxdesc.size == 0 ||
777 rxdesc.size > entry->queue->data_size)) {
778 rt2x00_err(rt2x00dev, "Wrong frame size %d max %d\n",
779 rxdesc.size, entry->queue->data_size);
780 dev_kfree_skb(entry->skb);
781 goto renew_skb;
782 }
783
784 /*
785 * The data behind the ieee80211 header must be
786 * aligned on a 4 byte boundary.
787 */
788 header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
789
790 /*
791 * Hardware might have stripped the IV/EIV/ICV data,
792 * in that case it is possible that the data was
793 * provided separately (through hardware descriptor)
794 * in which case we should reinsert the data into the frame.
795 */
796 if ((rxdesc.dev_flags & RXDONE_CRYPTO_IV) &&
797 (rxdesc.flags & RX_FLAG_IV_STRIPPED))
798 rt2x00crypto_rx_insert_iv(entry->skb, header_length,
799 &rxdesc);
800 else if (header_length &&
801 (rxdesc.size > header_length) &&
802 (rxdesc.dev_flags & RXDONE_L2PAD))
803 rt2x00queue_remove_l2pad(entry->skb, header_length);
804
805 /* Trim buffer to correct size */
806 skb_trim(entry->skb, rxdesc.size);
807
808 /*
809 * Translate the signal to the correct bitrate index.
810 */
811 rate_idx = rt2x00lib_rxdone_read_signal(rt2x00dev, &rxdesc);
812 if (rxdesc.rate_mode == RATE_MODE_HT_MIX ||
813 rxdesc.rate_mode == RATE_MODE_HT_GREENFIELD)
814 rxdesc.encoding = RX_ENC_HT;
815
816 /*
817 * Check if this is a beacon, and more frames have been
818 * buffered while we were in powersaving mode.
819 */
820 rt2x00lib_rxdone_check_ps(rt2x00dev, entry->skb, &rxdesc);
821
822 /*
823 * Check for incoming BlockAcks to match to the BlockAckReqs
824 * we've send out.
825 */
826 rt2x00lib_rxdone_check_ba(rt2x00dev, entry->skb, &rxdesc);
827
828 /*
829 * Update extra components
830 */
831 rt2x00link_update_stats(rt2x00dev, entry->skb, &rxdesc);
832 rt2x00debug_update_crypto(rt2x00dev, &rxdesc);
833 rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_RXDONE, entry);
834
835 /*
836 * Initialize RX status information, and send frame
837 * to mac80211.
838 */
839 rx_status = IEEE80211_SKB_RXCB(entry->skb);
840
841 /* Ensure that all fields of rx_status are initialized
842 * properly. The skb->cb array was used for driver
843 * specific informations, so rx_status might contain
844 * garbage.
845 */
846 memset(rx_status, 0, sizeof(*rx_status));
847
848 rx_status->mactime = rxdesc.timestamp;
849 rx_status->band = rt2x00dev->curr_band;
850 rx_status->freq = rt2x00dev->curr_freq;
851 rx_status->rate_idx = rate_idx;
852 rx_status->signal = rxdesc.rssi;
853 rx_status->flag = rxdesc.flags;
854 rx_status->enc_flags = rxdesc.enc_flags;
855 rx_status->encoding = rxdesc.encoding;
856 rx_status->bw = rxdesc.bw;
857 rx_status->antenna = rt2x00dev->link.ant.active.rx;
858
859 ieee80211_rx_ni(rt2x00dev->hw, entry->skb);
860
861 renew_skb:
862 /*
863 * Replace the skb with the freshly allocated one.
864 */
865 entry->skb = skb;
866
867 submit_entry:
868 entry->flags = 0;
869 rt2x00queue_index_inc(entry, Q_INDEX_DONE);
870 if (test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) &&
871 test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
872 rt2x00dev->ops->lib->clear_entry(entry);
873 }
874 EXPORT_SYMBOL_GPL(rt2x00lib_rxdone);
875
876 /*
877 * Driver initialization handlers.
878 */
879 const struct rt2x00_rate rt2x00_supported_rates[12] = {
880 {
881 .flags = DEV_RATE_CCK,
882 .bitrate = 10,
883 .ratemask = BIT(0),
884 .plcp = 0x00,
885 .mcs = RATE_MCS(RATE_MODE_CCK, 0),
886 },
887 {
888 .flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE,
889 .bitrate = 20,
890 .ratemask = BIT(1),
891 .plcp = 0x01,
892 .mcs = RATE_MCS(RATE_MODE_CCK, 1),
893 },
894 {
895 .flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE,
896 .bitrate = 55,
897 .ratemask = BIT(2),
898 .plcp = 0x02,
899 .mcs = RATE_MCS(RATE_MODE_CCK, 2),
900 },
901 {
902 .flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE,
903 .bitrate = 110,
904 .ratemask = BIT(3),
905 .plcp = 0x03,
906 .mcs = RATE_MCS(RATE_MODE_CCK, 3),
907 },
908 {
909 .flags = DEV_RATE_OFDM,
910 .bitrate = 60,
911 .ratemask = BIT(4),
912 .plcp = 0x0b,
913 .mcs = RATE_MCS(RATE_MODE_OFDM, 0),
914 },
915 {
916 .flags = DEV_RATE_OFDM,
917 .bitrate = 90,
918 .ratemask = BIT(5),
919 .plcp = 0x0f,
920 .mcs = RATE_MCS(RATE_MODE_OFDM, 1),
921 },
922 {
923 .flags = DEV_RATE_OFDM,
924 .bitrate = 120,
925 .ratemask = BIT(6),
926 .plcp = 0x0a,
927 .mcs = RATE_MCS(RATE_MODE_OFDM, 2),
928 },
929 {
930 .flags = DEV_RATE_OFDM,
931 .bitrate = 180,
932 .ratemask = BIT(7),
933 .plcp = 0x0e,
934 .mcs = RATE_MCS(RATE_MODE_OFDM, 3),
935 },
936 {
937 .flags = DEV_RATE_OFDM,
938 .bitrate = 240,
939 .ratemask = BIT(8),
940 .plcp = 0x09,
941 .mcs = RATE_MCS(RATE_MODE_OFDM, 4),
942 },
943 {
944 .flags = DEV_RATE_OFDM,
945 .bitrate = 360,
946 .ratemask = BIT(9),
947 .plcp = 0x0d,
948 .mcs = RATE_MCS(RATE_MODE_OFDM, 5),
949 },
950 {
951 .flags = DEV_RATE_OFDM,
952 .bitrate = 480,
953 .ratemask = BIT(10),
954 .plcp = 0x08,
955 .mcs = RATE_MCS(RATE_MODE_OFDM, 6),
956 },
957 {
958 .flags = DEV_RATE_OFDM,
959 .bitrate = 540,
960 .ratemask = BIT(11),
961 .plcp = 0x0c,
962 .mcs = RATE_MCS(RATE_MODE_OFDM, 7),
963 },
964 };
965
rt2x00lib_channel(struct ieee80211_channel * entry,const int channel,const int tx_power,const int value)966 static void rt2x00lib_channel(struct ieee80211_channel *entry,
967 const int channel, const int tx_power,
968 const int value)
969 {
970 /* XXX: this assumption about the band is wrong for 802.11j */
971 entry->band = channel <= 14 ? NL80211_BAND_2GHZ : NL80211_BAND_5GHZ;
972 entry->center_freq = ieee80211_channel_to_frequency(channel,
973 entry->band);
974 entry->hw_value = value;
975 entry->max_power = tx_power;
976 entry->max_antenna_gain = 0xff;
977 }
978
rt2x00lib_rate(struct ieee80211_rate * entry,const u16 index,const struct rt2x00_rate * rate)979 static void rt2x00lib_rate(struct ieee80211_rate *entry,
980 const u16 index, const struct rt2x00_rate *rate)
981 {
982 entry->flags = 0;
983 entry->bitrate = rate->bitrate;
984 entry->hw_value = index;
985 entry->hw_value_short = index;
986
987 if (rate->flags & DEV_RATE_SHORT_PREAMBLE)
988 entry->flags |= IEEE80211_RATE_SHORT_PREAMBLE;
989 }
990
rt2x00lib_set_mac_address(struct rt2x00_dev * rt2x00dev,u8 * eeprom_mac_addr)991 void rt2x00lib_set_mac_address(struct rt2x00_dev *rt2x00dev, u8 *eeprom_mac_addr)
992 {
993 const char *mac_addr;
994
995 mac_addr = of_get_mac_address(rt2x00dev->dev->of_node);
996 if (!IS_ERR(mac_addr))
997 ether_addr_copy(eeprom_mac_addr, mac_addr);
998
999 if (!is_valid_ether_addr(eeprom_mac_addr)) {
1000 eth_random_addr(eeprom_mac_addr);
1001 rt2x00_eeprom_dbg(rt2x00dev, "MAC: %pM\n", eeprom_mac_addr);
1002 }
1003 }
1004 EXPORT_SYMBOL_GPL(rt2x00lib_set_mac_address);
1005
rt2x00lib_probe_hw_modes(struct rt2x00_dev * rt2x00dev,struct hw_mode_spec * spec)1006 static int rt2x00lib_probe_hw_modes(struct rt2x00_dev *rt2x00dev,
1007 struct hw_mode_spec *spec)
1008 {
1009 struct ieee80211_hw *hw = rt2x00dev->hw;
1010 struct ieee80211_channel *channels;
1011 struct ieee80211_rate *rates;
1012 unsigned int num_rates;
1013 unsigned int i;
1014
1015 num_rates = 0;
1016 if (spec->supported_rates & SUPPORT_RATE_CCK)
1017 num_rates += 4;
1018 if (spec->supported_rates & SUPPORT_RATE_OFDM)
1019 num_rates += 8;
1020
1021 channels = kcalloc(spec->num_channels, sizeof(*channels), GFP_KERNEL);
1022 if (!channels)
1023 return -ENOMEM;
1024
1025 rates = kcalloc(num_rates, sizeof(*rates), GFP_KERNEL);
1026 if (!rates)
1027 goto exit_free_channels;
1028
1029 /*
1030 * Initialize Rate list.
1031 */
1032 for (i = 0; i < num_rates; i++)
1033 rt2x00lib_rate(&rates[i], i, rt2x00_get_rate(i));
1034
1035 /*
1036 * Initialize Channel list.
1037 */
1038 for (i = 0; i < spec->num_channels; i++) {
1039 rt2x00lib_channel(&channels[i],
1040 spec->channels[i].channel,
1041 spec->channels_info[i].max_power, i);
1042 }
1043
1044 /*
1045 * Intitialize 802.11b, 802.11g
1046 * Rates: CCK, OFDM.
1047 * Channels: 2.4 GHz
1048 */
1049 if (spec->supported_bands & SUPPORT_BAND_2GHZ) {
1050 rt2x00dev->bands[NL80211_BAND_2GHZ].n_channels = 14;
1051 rt2x00dev->bands[NL80211_BAND_2GHZ].n_bitrates = num_rates;
1052 rt2x00dev->bands[NL80211_BAND_2GHZ].channels = channels;
1053 rt2x00dev->bands[NL80211_BAND_2GHZ].bitrates = rates;
1054 hw->wiphy->bands[NL80211_BAND_2GHZ] =
1055 &rt2x00dev->bands[NL80211_BAND_2GHZ];
1056 memcpy(&rt2x00dev->bands[NL80211_BAND_2GHZ].ht_cap,
1057 &spec->ht, sizeof(spec->ht));
1058 }
1059
1060 /*
1061 * Intitialize 802.11a
1062 * Rates: OFDM.
1063 * Channels: OFDM, UNII, HiperLAN2.
1064 */
1065 if (spec->supported_bands & SUPPORT_BAND_5GHZ) {
1066 rt2x00dev->bands[NL80211_BAND_5GHZ].n_channels =
1067 spec->num_channels - 14;
1068 rt2x00dev->bands[NL80211_BAND_5GHZ].n_bitrates =
1069 num_rates - 4;
1070 rt2x00dev->bands[NL80211_BAND_5GHZ].channels = &channels[14];
1071 rt2x00dev->bands[NL80211_BAND_5GHZ].bitrates = &rates[4];
1072 hw->wiphy->bands[NL80211_BAND_5GHZ] =
1073 &rt2x00dev->bands[NL80211_BAND_5GHZ];
1074 memcpy(&rt2x00dev->bands[NL80211_BAND_5GHZ].ht_cap,
1075 &spec->ht, sizeof(spec->ht));
1076 }
1077
1078 return 0;
1079
1080 exit_free_channels:
1081 kfree(channels);
1082 rt2x00_err(rt2x00dev, "Allocation ieee80211 modes failed\n");
1083 return -ENOMEM;
1084 }
1085
rt2x00lib_remove_hw(struct rt2x00_dev * rt2x00dev)1086 static void rt2x00lib_remove_hw(struct rt2x00_dev *rt2x00dev)
1087 {
1088 if (test_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags))
1089 ieee80211_unregister_hw(rt2x00dev->hw);
1090
1091 if (likely(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ])) {
1092 kfree(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ]->channels);
1093 kfree(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ]->bitrates);
1094 rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ] = NULL;
1095 rt2x00dev->hw->wiphy->bands[NL80211_BAND_5GHZ] = NULL;
1096 }
1097
1098 kfree(rt2x00dev->spec.channels_info);
1099 }
1100
rt2x00lib_probe_hw(struct rt2x00_dev * rt2x00dev)1101 static int rt2x00lib_probe_hw(struct rt2x00_dev *rt2x00dev)
1102 {
1103 struct hw_mode_spec *spec = &rt2x00dev->spec;
1104 int status;
1105
1106 if (test_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags))
1107 return 0;
1108
1109 /*
1110 * Initialize HW modes.
1111 */
1112 status = rt2x00lib_probe_hw_modes(rt2x00dev, spec);
1113 if (status)
1114 return status;
1115
1116 /*
1117 * Initialize HW fields.
1118 */
1119 rt2x00dev->hw->queues = rt2x00dev->ops->tx_queues;
1120
1121 /*
1122 * Initialize extra TX headroom required.
1123 */
1124 rt2x00dev->hw->extra_tx_headroom =
1125 max_t(unsigned int, IEEE80211_TX_STATUS_HEADROOM,
1126 rt2x00dev->extra_tx_headroom);
1127
1128 /*
1129 * Take TX headroom required for alignment into account.
1130 */
1131 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_L2PAD))
1132 rt2x00dev->hw->extra_tx_headroom += RT2X00_L2PAD_SIZE;
1133 else if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DMA))
1134 rt2x00dev->hw->extra_tx_headroom += RT2X00_ALIGN_SIZE;
1135
1136 /*
1137 * Tell mac80211 about the size of our private STA structure.
1138 */
1139 rt2x00dev->hw->sta_data_size = sizeof(struct rt2x00_sta);
1140
1141 /*
1142 * Allocate tx status FIFO for driver use.
1143 */
1144 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_TXSTATUS_FIFO)) {
1145 /*
1146 * Allocate the txstatus fifo. In the worst case the tx
1147 * status fifo has to hold the tx status of all entries
1148 * in all tx queues. Hence, calculate the kfifo size as
1149 * tx_queues * entry_num and round up to the nearest
1150 * power of 2.
1151 */
1152 int kfifo_size =
1153 roundup_pow_of_two(rt2x00dev->ops->tx_queues *
1154 rt2x00dev->tx->limit *
1155 sizeof(u32));
1156
1157 status = kfifo_alloc(&rt2x00dev->txstatus_fifo, kfifo_size,
1158 GFP_KERNEL);
1159 if (status)
1160 return status;
1161 }
1162
1163 /*
1164 * Initialize tasklets if used by the driver. Tasklets are
1165 * disabled until the interrupts are turned on. The driver
1166 * has to handle that.
1167 */
1168 #define RT2X00_TASKLET_INIT(taskletname) \
1169 if (rt2x00dev->ops->lib->taskletname) { \
1170 tasklet_setup(&rt2x00dev->taskletname, \
1171 rt2x00dev->ops->lib->taskletname); \
1172 }
1173
1174 RT2X00_TASKLET_INIT(txstatus_tasklet);
1175 RT2X00_TASKLET_INIT(pretbtt_tasklet);
1176 RT2X00_TASKLET_INIT(tbtt_tasklet);
1177 RT2X00_TASKLET_INIT(rxdone_tasklet);
1178 RT2X00_TASKLET_INIT(autowake_tasklet);
1179
1180 #undef RT2X00_TASKLET_INIT
1181
1182 /*
1183 * Register HW.
1184 */
1185 status = ieee80211_register_hw(rt2x00dev->hw);
1186 if (status)
1187 return status;
1188
1189 set_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags);
1190
1191 return 0;
1192 }
1193
1194 /*
1195 * Initialization/uninitialization handlers.
1196 */
rt2x00lib_uninitialize(struct rt2x00_dev * rt2x00dev)1197 static void rt2x00lib_uninitialize(struct rt2x00_dev *rt2x00dev)
1198 {
1199 if (!test_and_clear_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags))
1200 return;
1201
1202 /*
1203 * Stop rfkill polling.
1204 */
1205 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1206 rt2x00rfkill_unregister(rt2x00dev);
1207
1208 /*
1209 * Allow the HW to uninitialize.
1210 */
1211 rt2x00dev->ops->lib->uninitialize(rt2x00dev);
1212
1213 /*
1214 * Free allocated queue entries.
1215 */
1216 rt2x00queue_uninitialize(rt2x00dev);
1217 }
1218
rt2x00lib_initialize(struct rt2x00_dev * rt2x00dev)1219 static int rt2x00lib_initialize(struct rt2x00_dev *rt2x00dev)
1220 {
1221 int status;
1222
1223 if (test_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags))
1224 return 0;
1225
1226 /*
1227 * Allocate all queue entries.
1228 */
1229 status = rt2x00queue_initialize(rt2x00dev);
1230 if (status)
1231 return status;
1232
1233 /*
1234 * Initialize the device.
1235 */
1236 status = rt2x00dev->ops->lib->initialize(rt2x00dev);
1237 if (status) {
1238 rt2x00queue_uninitialize(rt2x00dev);
1239 return status;
1240 }
1241
1242 set_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags);
1243
1244 /*
1245 * Start rfkill polling.
1246 */
1247 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1248 rt2x00rfkill_register(rt2x00dev);
1249
1250 return 0;
1251 }
1252
rt2x00lib_start(struct rt2x00_dev * rt2x00dev)1253 int rt2x00lib_start(struct rt2x00_dev *rt2x00dev)
1254 {
1255 int retval = 0;
1256
1257 /*
1258 * If this is the first interface which is added,
1259 * we should load the firmware now.
1260 */
1261 retval = rt2x00lib_load_firmware(rt2x00dev);
1262 if (retval)
1263 goto out;
1264
1265 /*
1266 * Initialize the device.
1267 */
1268 retval = rt2x00lib_initialize(rt2x00dev);
1269 if (retval)
1270 goto out;
1271
1272 rt2x00dev->intf_ap_count = 0;
1273 rt2x00dev->intf_sta_count = 0;
1274 rt2x00dev->intf_associated = 0;
1275
1276 /* Enable the radio */
1277 retval = rt2x00lib_enable_radio(rt2x00dev);
1278 if (retval)
1279 goto out;
1280
1281 set_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags);
1282
1283 out:
1284 return retval;
1285 }
1286
rt2x00lib_stop(struct rt2x00_dev * rt2x00dev)1287 void rt2x00lib_stop(struct rt2x00_dev *rt2x00dev)
1288 {
1289 if (!test_and_clear_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags))
1290 return;
1291
1292 /*
1293 * Perhaps we can add something smarter here,
1294 * but for now just disabling the radio should do.
1295 */
1296 rt2x00lib_disable_radio(rt2x00dev);
1297
1298 rt2x00dev->intf_ap_count = 0;
1299 rt2x00dev->intf_sta_count = 0;
1300 rt2x00dev->intf_associated = 0;
1301 }
1302
rt2x00lib_set_if_combinations(struct rt2x00_dev * rt2x00dev)1303 static inline void rt2x00lib_set_if_combinations(struct rt2x00_dev *rt2x00dev)
1304 {
1305 struct ieee80211_iface_limit *if_limit;
1306 struct ieee80211_iface_combination *if_combination;
1307
1308 if (rt2x00dev->ops->max_ap_intf < 2)
1309 return;
1310
1311 /*
1312 * Build up AP interface limits structure.
1313 */
1314 if_limit = &rt2x00dev->if_limits_ap;
1315 if_limit->max = rt2x00dev->ops->max_ap_intf;
1316 if_limit->types = BIT(NL80211_IFTYPE_AP);
1317 #ifdef CONFIG_MAC80211_MESH
1318 if_limit->types |= BIT(NL80211_IFTYPE_MESH_POINT);
1319 #endif
1320
1321 /*
1322 * Build up AP interface combinations structure.
1323 */
1324 if_combination = &rt2x00dev->if_combinations[IF_COMB_AP];
1325 if_combination->limits = if_limit;
1326 if_combination->n_limits = 1;
1327 if_combination->max_interfaces = if_limit->max;
1328 if_combination->num_different_channels = 1;
1329
1330 /*
1331 * Finally, specify the possible combinations to mac80211.
1332 */
1333 rt2x00dev->hw->wiphy->iface_combinations = rt2x00dev->if_combinations;
1334 rt2x00dev->hw->wiphy->n_iface_combinations = 1;
1335 }
1336
rt2x00dev_extra_tx_headroom(struct rt2x00_dev * rt2x00dev)1337 static unsigned int rt2x00dev_extra_tx_headroom(struct rt2x00_dev *rt2x00dev)
1338 {
1339 if (WARN_ON(!rt2x00dev->tx))
1340 return 0;
1341
1342 if (rt2x00_is_usb(rt2x00dev))
1343 return rt2x00dev->tx[0].winfo_size + rt2x00dev->tx[0].desc_size;
1344
1345 return rt2x00dev->tx[0].winfo_size;
1346 }
1347
1348 /*
1349 * driver allocation handlers.
1350 */
rt2x00lib_probe_dev(struct rt2x00_dev * rt2x00dev)1351 int rt2x00lib_probe_dev(struct rt2x00_dev *rt2x00dev)
1352 {
1353 int retval = -ENOMEM;
1354
1355 /*
1356 * Set possible interface combinations.
1357 */
1358 rt2x00lib_set_if_combinations(rt2x00dev);
1359
1360 /*
1361 * Allocate the driver data memory, if necessary.
1362 */
1363 if (rt2x00dev->ops->drv_data_size > 0) {
1364 rt2x00dev->drv_data = kzalloc(rt2x00dev->ops->drv_data_size,
1365 GFP_KERNEL);
1366 if (!rt2x00dev->drv_data) {
1367 retval = -ENOMEM;
1368 goto exit;
1369 }
1370 }
1371
1372 spin_lock_init(&rt2x00dev->irqmask_lock);
1373 mutex_init(&rt2x00dev->csr_mutex);
1374 mutex_init(&rt2x00dev->conf_mutex);
1375 INIT_LIST_HEAD(&rt2x00dev->bar_list);
1376 spin_lock_init(&rt2x00dev->bar_list_lock);
1377 hrtimer_init(&rt2x00dev->txstatus_timer, CLOCK_MONOTONIC,
1378 HRTIMER_MODE_REL);
1379
1380 set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags);
1381
1382 /*
1383 * Make room for rt2x00_intf inside the per-interface
1384 * structure ieee80211_vif.
1385 */
1386 rt2x00dev->hw->vif_data_size = sizeof(struct rt2x00_intf);
1387
1388 /*
1389 * rt2x00 devices can only use the last n bits of the MAC address
1390 * for virtual interfaces.
1391 */
1392 rt2x00dev->hw->wiphy->addr_mask[ETH_ALEN - 1] =
1393 (rt2x00dev->ops->max_ap_intf - 1);
1394
1395 /*
1396 * Initialize work.
1397 */
1398 rt2x00dev->workqueue =
1399 alloc_ordered_workqueue("%s", 0, wiphy_name(rt2x00dev->hw->wiphy));
1400 if (!rt2x00dev->workqueue) {
1401 retval = -ENOMEM;
1402 goto exit;
1403 }
1404
1405 INIT_WORK(&rt2x00dev->intf_work, rt2x00lib_intf_scheduled);
1406 INIT_DELAYED_WORK(&rt2x00dev->autowakeup_work, rt2x00lib_autowakeup);
1407 INIT_WORK(&rt2x00dev->sleep_work, rt2x00lib_sleep);
1408
1409 /*
1410 * Let the driver probe the device to detect the capabilities.
1411 */
1412 retval = rt2x00dev->ops->lib->probe_hw(rt2x00dev);
1413 if (retval) {
1414 rt2x00_err(rt2x00dev, "Failed to allocate device\n");
1415 goto exit;
1416 }
1417
1418 /*
1419 * Allocate queue array.
1420 */
1421 retval = rt2x00queue_allocate(rt2x00dev);
1422 if (retval)
1423 goto exit;
1424
1425 /* Cache TX headroom value */
1426 rt2x00dev->extra_tx_headroom = rt2x00dev_extra_tx_headroom(rt2x00dev);
1427
1428 /*
1429 * Determine which operating modes are supported, all modes
1430 * which require beaconing, depend on the availability of
1431 * beacon entries.
1432 */
1433 rt2x00dev->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
1434 if (rt2x00dev->bcn->limit > 0)
1435 rt2x00dev->hw->wiphy->interface_modes |=
1436 BIT(NL80211_IFTYPE_ADHOC) |
1437 #ifdef CONFIG_MAC80211_MESH
1438 BIT(NL80211_IFTYPE_MESH_POINT) |
1439 #endif
1440 #ifdef CONFIG_WIRELESS_WDS
1441 BIT(NL80211_IFTYPE_WDS) |
1442 #endif
1443 BIT(NL80211_IFTYPE_AP);
1444
1445 rt2x00dev->hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN;
1446
1447 wiphy_ext_feature_set(rt2x00dev->hw->wiphy,
1448 NL80211_EXT_FEATURE_CQM_RSSI_LIST);
1449
1450 /*
1451 * Initialize ieee80211 structure.
1452 */
1453 retval = rt2x00lib_probe_hw(rt2x00dev);
1454 if (retval) {
1455 rt2x00_err(rt2x00dev, "Failed to initialize hw\n");
1456 goto exit;
1457 }
1458
1459 /*
1460 * Register extra components.
1461 */
1462 rt2x00link_register(rt2x00dev);
1463 rt2x00leds_register(rt2x00dev);
1464 rt2x00debug_register(rt2x00dev);
1465
1466 /*
1467 * Start rfkill polling.
1468 */
1469 if (!rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1470 rt2x00rfkill_register(rt2x00dev);
1471
1472 return 0;
1473
1474 exit:
1475 rt2x00lib_remove_dev(rt2x00dev);
1476
1477 return retval;
1478 }
1479 EXPORT_SYMBOL_GPL(rt2x00lib_probe_dev);
1480
rt2x00lib_remove_dev(struct rt2x00_dev * rt2x00dev)1481 void rt2x00lib_remove_dev(struct rt2x00_dev *rt2x00dev)
1482 {
1483 clear_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags);
1484
1485 /*
1486 * Stop rfkill polling.
1487 */
1488 if (!rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1489 rt2x00rfkill_unregister(rt2x00dev);
1490
1491 /*
1492 * Disable radio.
1493 */
1494 rt2x00lib_disable_radio(rt2x00dev);
1495
1496 /*
1497 * Stop all work.
1498 */
1499 cancel_work_sync(&rt2x00dev->intf_work);
1500 cancel_delayed_work_sync(&rt2x00dev->autowakeup_work);
1501 cancel_work_sync(&rt2x00dev->sleep_work);
1502
1503 hrtimer_cancel(&rt2x00dev->txstatus_timer);
1504
1505 /*
1506 * Kill the tx status tasklet.
1507 */
1508 tasklet_kill(&rt2x00dev->txstatus_tasklet);
1509 tasklet_kill(&rt2x00dev->pretbtt_tasklet);
1510 tasklet_kill(&rt2x00dev->tbtt_tasklet);
1511 tasklet_kill(&rt2x00dev->rxdone_tasklet);
1512 tasklet_kill(&rt2x00dev->autowake_tasklet);
1513
1514 /*
1515 * Uninitialize device.
1516 */
1517 rt2x00lib_uninitialize(rt2x00dev);
1518
1519 if (rt2x00dev->workqueue)
1520 destroy_workqueue(rt2x00dev->workqueue);
1521
1522 /*
1523 * Free the tx status fifo.
1524 */
1525 kfifo_free(&rt2x00dev->txstatus_fifo);
1526
1527 /*
1528 * Free extra components
1529 */
1530 rt2x00debug_deregister(rt2x00dev);
1531 rt2x00leds_unregister(rt2x00dev);
1532
1533 /*
1534 * Free ieee80211_hw memory.
1535 */
1536 rt2x00lib_remove_hw(rt2x00dev);
1537
1538 /*
1539 * Free firmware image.
1540 */
1541 rt2x00lib_free_firmware(rt2x00dev);
1542
1543 /*
1544 * Free queue structures.
1545 */
1546 rt2x00queue_free(rt2x00dev);
1547
1548 /*
1549 * Free the driver data.
1550 */
1551 kfree(rt2x00dev->drv_data);
1552 }
1553 EXPORT_SYMBOL_GPL(rt2x00lib_remove_dev);
1554
1555 /*
1556 * Device state handlers
1557 */
rt2x00lib_suspend(struct rt2x00_dev * rt2x00dev)1558 int rt2x00lib_suspend(struct rt2x00_dev *rt2x00dev)
1559 {
1560 rt2x00_dbg(rt2x00dev, "Going to sleep\n");
1561
1562 /*
1563 * Prevent mac80211 from accessing driver while suspended.
1564 */
1565 if (!test_and_clear_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
1566 return 0;
1567
1568 /*
1569 * Cleanup as much as possible.
1570 */
1571 rt2x00lib_uninitialize(rt2x00dev);
1572
1573 /*
1574 * Suspend/disable extra components.
1575 */
1576 rt2x00leds_suspend(rt2x00dev);
1577 rt2x00debug_deregister(rt2x00dev);
1578
1579 /*
1580 * Set device mode to sleep for power management,
1581 * on some hardware this call seems to consistently fail.
1582 * From the specifications it is hard to tell why it fails,
1583 * and if this is a "bad thing".
1584 * Overall it is safe to just ignore the failure and
1585 * continue suspending. The only downside is that the
1586 * device will not be in optimal power save mode, but with
1587 * the radio and the other components already disabled the
1588 * device is as good as disabled.
1589 */
1590 if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_SLEEP))
1591 rt2x00_warn(rt2x00dev, "Device failed to enter sleep state, continue suspending\n");
1592
1593 return 0;
1594 }
1595 EXPORT_SYMBOL_GPL(rt2x00lib_suspend);
1596
rt2x00lib_resume(struct rt2x00_dev * rt2x00dev)1597 int rt2x00lib_resume(struct rt2x00_dev *rt2x00dev)
1598 {
1599 rt2x00_dbg(rt2x00dev, "Waking up\n");
1600
1601 /*
1602 * Restore/enable extra components.
1603 */
1604 rt2x00debug_register(rt2x00dev);
1605 rt2x00leds_resume(rt2x00dev);
1606
1607 /*
1608 * We are ready again to receive requests from mac80211.
1609 */
1610 set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags);
1611
1612 return 0;
1613 }
1614 EXPORT_SYMBOL_GPL(rt2x00lib_resume);
1615
1616 /*
1617 * rt2x00lib module information.
1618 */
1619 MODULE_AUTHOR(DRV_PROJECT);
1620 MODULE_VERSION(DRV_VERSION);
1621 MODULE_DESCRIPTION("rt2x00 library");
1622 MODULE_LICENSE("GPL");
1623