| /kernel/linux/linux-5.10/drivers/spi/ |
| D | Makefile | 3 # Makefile for kernel SPI drivers.
10 obj-$(CONFIG_SPI_MASTER) += spi.o
11 obj-$(CONFIG_SPI_MEM) += spi-mem.o
12 obj-$(CONFIG_SPI_MUX) += spi-mux.o
14 obj-$(CONFIG_SPI_LOOPBACK_TEST) += spi-loopback-test.o
16 # SPI master controller drivers (bus)
17 obj-$(CONFIG_SPI_ALTERA) += spi-altera.o
18 obj-$(CONFIG_SPI_AR934X) += spi-ar934x.o
19 obj-$(CONFIG_SPI_ARMADA_3700) += spi-armada-3700.o
20 obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o
[all …]
|
| D | Kconfig | 3 # SPI driver configuration
5 menuconfig SPI config
6 bool "SPI support"
10 protocol. Chips that support SPI can have data transfer rates
12 controller and a chipselect. Most SPI slaves don't support
15 SPI is widely used by microcontrollers to talk with sensors,
18 MMC and SD cards can be accessed using SPI protocol; and for
19 DataFlash cards used in MMC sockets, SPI must always be used.
21 SPI is one of a family of similar protocols using a four wire
26 if SPI
[all …]
|
| D | spi-stm32.c | 3 // STMicroelectronics STM32 SPI Controller driver (master mode only)
19 #include <linux/spi/spi.h>
23 /* STM32F4 SPI registers */
72 /* STM32F4 SPI Baud Rate min/max divisor */
76 /* STM32H7 SPI registers */
153 /* STM32H7 SPI Master Baud Rate min/max divisor */
157 /* STM32H7 SPI Communication mode */
163 /* SPI Communication type */
179 * struct stm32_spi_reg - stm32 SPI register & bitfield desc
192 * @en: enable register and SPI enable bit
[all …]
|
| D | spi-lantiq-ssc.c | 19 #include <linux/spi/spi.h>
155 int (*cfg_irq)(struct platform_device *pdev, struct lantiq_ssc_spi *spi);
188 static u32 lantiq_ssc_readl(const struct lantiq_ssc_spi *spi, u32 reg) in lantiq_ssc_readl() argument
190 return __raw_readl(spi->regbase + reg); in lantiq_ssc_readl()
193 static void lantiq_ssc_writel(const struct lantiq_ssc_spi *spi, u32 val, in lantiq_ssc_writel() argument
196 __raw_writel(val, spi->regbase + reg); in lantiq_ssc_writel()
199 static void lantiq_ssc_maskl(const struct lantiq_ssc_spi *spi, u32 clr, in lantiq_ssc_maskl() argument
202 u32 val = __raw_readl(spi->regbase + reg); in lantiq_ssc_maskl()
206 __raw_writel(val, spi->regbase + reg); in lantiq_ssc_maskl()
209 static unsigned int tx_fifo_level(const struct lantiq_ssc_spi *spi) in tx_fifo_level() argument
[all …]
|
| D | spi-mux.c | 3 // General Purpose SPI multiplexer
10 #include <linux/spi/spi.h>
17 * This driver supports a MUX on an SPI bus. This can be useful when you need
21 * The driver will create an additional SPI controller. Devices added under the
27 * @spi: pointer to the device struct attached to the parent
28 * spi controller
36 * downstream spi devices
39 struct spi_device *spi; member
49 static int spi_mux_select(struct spi_device *spi) in spi_mux_select() argument
51 struct spi_mux_priv *priv = spi_controller_get_devdata(spi->controller); in spi_mux_select()
[all …]
|
| D | spi-sifive.c | 5 // SiFive SPI controller driver (master mode only)
15 #include <linux/spi/spi.h>
38 #define SIFIVE_SPI_REG_FCTRL 0x60 /* SPI flash interface control */
39 #define SIFIVE_SPI_REG_FFMT 0x64 /* SPI flash instruction format */
99 static void sifive_spi_write(struct sifive_spi *spi, int offset, u32 value) in sifive_spi_write() argument
101 iowrite32(value, spi->regs + offset); in sifive_spi_write()
104 static u32 sifive_spi_read(struct sifive_spi *spi, int offset) in sifive_spi_read() argument
106 return ioread32(spi->regs + offset); in sifive_spi_read()
109 static void sifive_spi_init(struct sifive_spi *spi) in sifive_spi_init() argument
112 sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0); in sifive_spi_init()
[all …]
|
| D | spi-orion.c | 3 * Marvell Orion SPI controller driver
14 #include <linux/spi/spi.h>
74 * have both is for managing the armada-370-spi case with old
130 static int orion_spi_baudrate_set(struct spi_device *spi, unsigned int speed) in orion_spi_baudrate_set() argument
139 orion_spi = spi_master_get_devdata(spi->master); in orion_spi_baudrate_set()
216 /* Convert the rate to SPI clock divisor value. */ in orion_spi_baudrate_set()
228 orion_spi_mode_set(struct spi_device *spi) in orion_spi_mode_set() argument
233 orion_spi = spi_master_get_devdata(spi->master); in orion_spi_mode_set()
237 if (spi->mode & SPI_CPOL) in orion_spi_mode_set()
239 if (spi->mode & SPI_CPHA) in orion_spi_mode_set()
[all …]
|
| D | spi-omap2-mcspi.c | 28 #include <linux/spi/spi.h>
30 #include <linux/platform_data/spi-omap2-mcspi.h>
159 static inline void mcspi_write_cs_reg(const struct spi_device *spi, in mcspi_write_cs_reg() argument
162 struct omap2_mcspi_cs *cs = spi->controller_state; in mcspi_write_cs_reg()
167 static inline u32 mcspi_read_cs_reg(const struct spi_device *spi, int idx) in mcspi_read_cs_reg() argument
169 struct omap2_mcspi_cs *cs = spi->controller_state; in mcspi_read_cs_reg()
174 static inline u32 mcspi_cached_chconf0(const struct spi_device *spi) in mcspi_cached_chconf0() argument
176 struct omap2_mcspi_cs *cs = spi->controller_state; in mcspi_cached_chconf0()
181 static inline void mcspi_write_chconf0(const struct spi_device *spi, u32 val) in mcspi_write_chconf0() argument
183 struct omap2_mcspi_cs *cs = spi->controller_state; in mcspi_write_chconf0()
[all …]
|
| /kernel/linux/linux-5.10/drivers/staging/pi433/ |
| D | rf69.c | 3 * abstraction of the spi interface of HopeRf rf69 radio module
17 #include <linux/spi/spi.h>
27 static u8 rf69_read_reg(struct spi_device *spi, u8 addr) in rf69_read_reg() argument
31 retval = spi_w8r8(spi, addr); in rf69_read_reg()
40 dev_dbg(&spi->dev, "read 0x%x FAILED\n", addr); in rf69_read_reg()
42 dev_dbg(&spi->dev, "read 0x%x from reg 0x%x\n", retval, addr); in rf69_read_reg()
48 static int rf69_write_reg(struct spi_device *spi, u8 addr, u8 value) in rf69_write_reg() argument
56 retval = spi_write(spi, &buffer, 2); in rf69_write_reg()
65 dev_dbg(&spi->dev, "write 0x%x to 0x%x FAILED\n", value, addr); in rf69_write_reg()
67 dev_dbg(&spi->dev, "wrote 0x%x to reg 0x%x\n", value, addr); in rf69_write_reg()
[all …]
|
| D | rf69.h | 20 int rf69_set_mode(struct spi_device *spi, enum mode mode);
21 int rf69_set_data_mode(struct spi_device *spi, u8 data_mode);
22 int rf69_set_modulation(struct spi_device *spi, enum modulation modulation);
23 int rf69_set_modulation_shaping(struct spi_device *spi,
25 int rf69_set_bit_rate(struct spi_device *spi, u16 bit_rate);
26 int rf69_set_deviation(struct spi_device *spi, u32 deviation);
27 int rf69_set_frequency(struct spi_device *spi, u32 frequency);
28 int rf69_enable_amplifier(struct spi_device *spi, u8 amplifier_mask);
29 int rf69_disable_amplifier(struct spi_device *spi, u8 amplifier_mask);
30 int rf69_set_output_power_level(struct spi_device *spi, u8 power_level);
[all …]
|
| /kernel/linux/linux-5.10/drivers/staging/greybus/ |
| D | spilib.c | 3 * Greybus SPI library
14 #include <linux/spi/spi.h>
45 static struct spi_master *get_master_from_spi(struct gb_spilib *spi) in get_master_from_spi() argument
47 return gb_connection_get_data(spi->connection); in get_master_from_spi()
95 static void clean_xfer_state(struct gb_spilib *spi) in clean_xfer_state() argument
97 spi->first_xfer = NULL; in clean_xfer_state()
98 spi->last_xfer = NULL; in clean_xfer_state()
99 spi->rx_xfer_offset = 0; in clean_xfer_state()
100 spi->tx_xfer_offset = 0; in clean_xfer_state()
101 spi->last_xfer_size = 0; in clean_xfer_state()
[all …]
|
| /kernel/linux/linux-5.10/drivers/video/backlight/ |
| D | ili922x.c | 7 * controller. The interface to the display is SPI and the display's
20 #include <linux/spi/spi.h>
105 * for the SPI transfer. According to the datasheet, the controller
110 * @s: pointer to an SPI device
139 struct spi_device *spi; member
146 * @spi: spi device
149 static int ili922x_read_status(struct spi_device *spi, u16 *rs) in ili922x_read_status() argument
162 CHECK_FREQ_REG(spi, &xfer); in ili922x_read_status()
176 ret = spi_sync(spi, &msg); in ili922x_read_status()
178 dev_dbg(&spi->dev, "Error sending SPI message 0x%x", ret); in ili922x_read_status()
[all …]
|
| D | l4f00242t03.c | 21 #include <linux/spi/spi.h>
24 struct spi_device *spi; member
46 static void l4f00242t03_lcd_init(struct spi_device *spi) in l4f00242t03_lcd_init() argument
48 struct l4f00242t03_priv *priv = spi_get_drvdata(spi); in l4f00242t03_lcd_init()
52 dev_dbg(&spi->dev, "initializing LCD\n"); in l4f00242t03_lcd_init()
56 dev_err(&spi->dev, "failed to set the IO regulator voltage.\n"); in l4f00242t03_lcd_init()
61 dev_err(&spi->dev, "failed to enable the IO regulator.\n"); in l4f00242t03_lcd_init()
67 dev_err(&spi->dev, "failed to set the core regulator voltage.\n"); in l4f00242t03_lcd_init()
73 dev_err(&spi->dev, "failed to enable the core regulator.\n"); in l4f00242t03_lcd_init()
82 spi_write(spi, (const u8 *)cmd, ARRAY_SIZE(cmd) * sizeof(u16)); in l4f00242t03_lcd_init()
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/spi/ |
| D | brcm,spi-bcm-qspi.txt | 1 Broadcom SPI controller
3 The Broadcom SPI controller is a SPI master found on various SOCs, including
4 BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits
6 MSPI : SPI master controller can read and write to a SPI slave device
7 BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration
14 use SPI protocol.
19 Must be <1>, as required by generic SPI binding.
22 Must be <0>, also as required by generic SPI binding.
26 "brcm,spi-brcmstb-qspi", "brcm,spi-bcm-qspi" : MSPI+BSPI on BRCMSTB SoCs
27 "brcm,spi-brcmstb-mspi", "brcm,spi-bcm-qspi" : Second Instance of MSPI
[all …]
|
| D | qcom,spi-qup.txt | 1 Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
4 and an input FIFO) for serial peripheral interface (SPI) mini-core.
6 SPI in master mode supports up to 50MHz, up to four chip selects, programmable
11 "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064.
12 "qcom,spi-qup-v2.1.1" for 8974 and later
13 "qcom,spi-qup-v2.2.1" for 8974 v2 and later.
23 address on the SPI bus. Should be set to 1.
27 - spi-max-frequency: Specifies maximum SPI clock frequency,
29 Documentation/devicetree/bindings/spi/spi-bus.txt
32 The gpios will be referred to as reg = <index> in the SPI child
[all …]
|
| D | spi-mt65xx.txt | 1 Binding for MTK SPI controller
5 - mediatek,mt2701-spi: for mt2701 platforms
6 - mediatek,mt2712-spi: for mt2712 platforms
7 - mediatek,mt6589-spi: for mt6589 platforms
8 - mediatek,mt6765-spi: for mt6765 platforms
9 - mediatek,mt7622-spi: for mt7622 platforms
10 - "mediatek,mt7629-spi", "mediatek,mt7622-spi": for mt7629 platforms
11 - mediatek,mt8135-spi: for mt8135 platforms
12 - mediatek,mt8173-spi: for mt8173 platforms
13 - mediatek,mt8183-spi: for mt8183 platforms
[all …]
|
| D | spi-controller.yaml | 4 $id: http://devicetree.org/schemas/spi/spi-controller.yaml#
7 title: SPI Controller Generic Binding
13 SPI busses can be described with a node for the SPI controller device
14 and a set of child nodes for each SPI slave on the bus. The system SPI
15 controller may be described for use in SPI master mode or in SPI slave mode,
20 pattern: "^spi(@.*|-[0-9a-f])*$"
50 spi-slave:
53 The SPI controller acts as a slave, instead of a master.
59 - spi-slave
76 Compatible of the SPI device.
[all …]
|
| /kernel/linux/linux-5.10/drivers/net/wan/ |
| D | slic_ds26522.c | 16 #include <linux/spi/spi.h>
37 static void slic_write(struct spi_device *spi, u16 addr, in slic_write() argument
48 /* write spi addr and value */ in slic_write()
49 spi_write(spi, &temp[0], SLIC_THREE_LEN); in slic_write()
52 static u8 slic_read(struct spi_device *spi, u16 addr) in slic_read() argument
61 spi_write_then_read(spi, &temp[0], SLIC_TWO_LEN, &data, in slic_read()
68 static bool get_slic_product_code(struct spi_device *spi) in get_slic_product_code() argument
72 device_id = slic_read(spi, DS26522_IDR_ADDR); in get_slic_product_code()
79 static void ds26522_e1_spec_config(struct spi_device *spi) in ds26522_e1_spec_config() argument
82 slic_write(spi, DS26522_RMMR_ADDR, DS26522_RMMR_E1); in ds26522_e1_spec_config()
[all …]
|
| /kernel/linux/linux-5.10/drivers/media/pci/netup_unidvb/ |
| D | netup_unidvb_spi.c | 5 * Internal SPI driver for NetUP Universal Dual DVB-CI
13 #include <linux/spi/spi.h>
14 #include <linux/spi/flash.h>
69 irqreturn_t netup_spi_interrupt(struct netup_spi *spi) in netup_spi_interrupt() argument
74 if (!spi) in netup_spi_interrupt()
77 spin_lock_irqsave(&spi->lock, flags); in netup_spi_interrupt()
78 reg = readw(&spi->regs->control_stat); in netup_spi_interrupt()
80 spin_unlock_irqrestore(&spi->lock, flags); in netup_spi_interrupt()
81 dev_dbg(&spi->master->dev, in netup_spi_interrupt()
85 writew(reg | NETUP_SPI_CTRL_IRQ, &spi->regs->control_stat); in netup_spi_interrupt()
[all …]
|
| /kernel/linux/linux-5.10/drivers/net/can/spi/ |
| D | mcp251x.c | 2 /* CAN bus driver for Microchip 251x/25625 CAN Controller with SPI Interface
43 #include <linux/spi/spi.h>
46 /* SPI interface instruction set */
197 /* Buffer size required for the largest SPI transfer (i.e., reading a
231 struct spi_device *spi; member
234 struct mutex mcp_lock; /* SPI device lock */
263 static inline int mcp251x_is_##_model(struct spi_device *spi) \
265 struct mcp251x_priv *priv = spi_get_drvdata(spi); \
285 * registers via SPI is not really different conceptually than using
296 static int mcp251x_spi_trans(struct spi_device *spi, int len) in mcp251x_spi_trans() argument
[all …]
|
| D | hi311x.c | 2 /* CAN bus driver for Holt HI3110 CAN Controller with SPI Interface
35 #include <linux/spi/spi.h>
147 struct spi_device *spi; member
150 struct mutex hi3110_lock; /* SPI device lock */
188 * registers via SPI is not really different conceptually than using
199 static int hi3110_spi_trans(struct spi_device *spi, int len) in hi3110_spi_trans() argument
201 struct hi3110_priv *priv = spi_get_drvdata(spi); in hi3110_spi_trans()
214 ret = spi_sync(spi, &m); in hi3110_spi_trans()
217 dev_err(&spi->dev, "spi transfer failed: ret = %d\n", ret); in hi3110_spi_trans()
221 static int hi3110_cmd(struct spi_device *spi, u8 command) in hi3110_cmd() argument
[all …]
|
| /kernel/linux/linux-5.10/drivers/media/dvb-frontends/cxd2880/ |
| D | cxd2880_spi_device.c | 5 * SPI access functions
10 #include <linux/spi/spi.h>
14 static int cxd2880_spi_device_write(struct cxd2880_spi *spi, in cxd2880_spi_device_write() argument
22 if (!spi || !spi->user || !data || size == 0) in cxd2880_spi_device_write()
25 spi_device = spi->user; in cxd2880_spi_device_write()
33 result = spi_sync(spi_device->spi, &msg); in cxd2880_spi_device_write()
41 static int cxd2880_spi_device_write_read(struct cxd2880_spi *spi, in cxd2880_spi_device_write_read() argument
50 if (!spi || !spi->user || !tx_data || in cxd2880_spi_device_write_read()
54 spi_device = spi->user; in cxd2880_spi_device_write_read()
56 result = spi_write_then_read(spi_device->spi, tx_data, in cxd2880_spi_device_write_read()
[all …]
|
| /kernel/linux/linux-5.10/drivers/video/fbdev/omap2/omapfb/displays/ |
| D | panel-lgphilips-lb035q02.c | 12 #include <linux/spi/spi.h>
43 struct spi_device *spi; member
57 static int lb035q02_write_reg(struct spi_device *spi, u8 reg, u16 val) in lb035q02_write_reg() argument
85 return spi_sync(spi, &msg); in lb035q02_write_reg()
88 static void init_lb035q02_panel(struct spi_device *spi) in init_lb035q02_panel() argument
91 lb035q02_write_reg(spi, 0x01, 0x6300); in init_lb035q02_panel()
92 lb035q02_write_reg(spi, 0x02, 0x0200); in init_lb035q02_panel()
93 lb035q02_write_reg(spi, 0x03, 0x0177); in init_lb035q02_panel()
94 lb035q02_write_reg(spi, 0x04, 0x04c7); in init_lb035q02_panel()
95 lb035q02_write_reg(spi, 0x05, 0xffc0); in init_lb035q02_panel()
[all …]
|
| /kernel/linux/linux-5.10/drivers/iio/common/st_sensors/ |
| D | st_sensors_spi.c | 3 * STMicroelectronics sensors spi library driver
34 * st_sensors_is_spi_3_wire() - check if SPI 3-wire mode has been selected
35 * @spi: spi device reference.
37 * Return: true if SPI 3-wire mode is selected, false otherwise.
39 static bool st_sensors_is_spi_3_wire(struct spi_device *spi) in st_sensors_is_spi_3_wire() argument
42 struct device *dev = &spi->dev; in st_sensors_is_spi_3_wire()
44 if (device_property_read_bool(dev, "spi-3wire")) in st_sensors_is_spi_3_wire()
55 * st_sensors_configure_spi_3_wire() - configure SPI 3-wire if needed
56 * @spi: spi device reference.
61 static int st_sensors_configure_spi_3_wire(struct spi_device *spi, in st_sensors_configure_spi_3_wire() argument
[all …]
|
| /kernel/linux/linux-5.10/drivers/media/v4l2-core/ |
| D | v4l2-spi.c | 3 * v4l2-spi - SPI helpers for Video4Linux2
7 #include <linux/spi/spi.h>
13 struct spi_device *spi = v4l2_get_subdevdata(sd); in v4l2_spi_subdev_unregister() local
15 if (spi && !spi->dev.of_node && !spi->dev.fwnode) in v4l2_spi_subdev_unregister()
16 spi_unregister_device(spi); in v4l2_spi_subdev_unregister()
19 void v4l2_spi_subdev_init(struct v4l2_subdev *sd, struct spi_device *spi, in v4l2_spi_subdev_init() argument
25 sd->owner = spi->dev.driver->owner; in v4l2_spi_subdev_init()
26 sd->dev = &spi->dev; in v4l2_spi_subdev_init()
28 v4l2_set_subdevdata(sd, spi); in v4l2_spi_subdev_init()
29 spi_set_drvdata(spi, sd); in v4l2_spi_subdev_init()
[all …]
|