Searched refs:AC (Results 1 – 25 of 87) sorted by relevance
1234
| /kernel/linux/linux-5.10/Documentation/ABI/testing/ |
| D | sysfs-devices-platform-ACPI-TAD | 11 BIT(0): AC wakeup implemented if set
16 BIT(5): The AC timer wakes up from S4 if set
17 BIT(6): The AC timer wakes up from S5 if set
28 (RW) The AC alarm timer value.
30 Reads return the current AC alarm timer value in seconds or
31 "disabled", if the AC alarm is not set to wake up the system.
33 Write a new AC alarm timer value in seconds or "disabled" to it
34 to set the AC alarm timer or to disable it, respectively.
36 If the AC alarm timer is set through this attribute and it
45 (RW) The AC alarm expired timer wake policy (see ACPI 6.2,
[all …]
|
| D | sysfs-platform-wilco-ec | 5 Boot on AC is a policy which makes the device boot from S5
6 when AC power is connected. This is useful for users who
45 supplied to the port when on AC or if battery is > 50%.
48 to the port when on AC. Else no power is supplied.
|
| D | sysfs-platform-dptf | 14 Must be 0 if no AC Adaptor is plugged in.
34 - 0x01 = AC
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/power/supply/ |
| D | tps65217_charger.txt | 5 -interrupts: TPS65217 interrupt numbers for the AC and USB charger input change.
6 Should be <0> for the USB charger and <1> for the AC adapter.
7 -interrupt-names: Should be "USB" and "AC"
16 interrupt-names = "USB", "AC";
|
| D | ti,bq24735.txt | 8 - interrupts : Specify the interrupt to be used to trigger when the AC
10 - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter
13 the GPIO must be active on AC adapter absence despite ACOK being active
14 (high) on AC adapter presence.
30 - poll-interval : In case 'interrupts' is not specified, poll AC adapter
|
| D | axp20x_ac_power.txt | 1 AXP20X and AXP22X PMICs' AC power supply
11 The AXP20X can read the current current and voltage supplied by AC by
14 The AXP22X is only able to tell if an AC power supply is present and
|
| D | lp8727_charger.txt | 11 AC and USB charging parameters
30 /* AC charger: 5% EOC and 500mA charging current */
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/sound/ |
| D | cs43130.txt | 32 Boolean, define to enable headphone AC impedance measurement.
33 DC impedance must also be enabled for AC impedance measurement.
40 Define the frequencies at which to measure HP AC impedance.
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/ddr/ |
| D | lpddr3-timings.txt | 1 * AC timing parameters of LPDDR3 memories for a given speed-bin.
12 The following properties represent AC timing parameters from the memory
|
| D | lpddr2-timings.txt | 1 * AC timing parameters of LPDDR2(JESD209-2) memories for a given speed-bin
10 The following properties represent AC timing parameters from the memory
|
| D | lpddr3.txt | 15 The following optional properties represent the minimum value of some AC
42 "lpddr3-timings" provides AC timing parameters of the device for
|
| D | lpddr2.txt | 19 The following optional properties represent the minimum value of some AC
36 "lpddr2-timings" provides AC timing parameters of the device for
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/display/ |
| D | cirrus,clps711x-fb.txt | 12 - ac-prescale : LCD AC bias frequency. This frequency is the required
13 AC bias frequency for a given manufacturer's LCD plate.
|
| /kernel/linux/linux-5.10/Documentation/driver-api/memory-devices/ |
| D | ti-emif.rst | 32 functions of the driver includes re-configuring AC timing
42 - Device AC timings: 'struct lpddr2_timings' and 'struct lpddr2_min_tck'
|
| /kernel/linux/linux-5.10/Documentation/networking/ |
| D | proc_net_tcp.rst | 18 46: 010310AC:9C4C 030310AC:1770 01
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/display/tilcdc/ |
| D | panel.txt | 6 - ac-bias: AC Bias Pin Frequency
7 - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
|
| /kernel/linux/linux-5.10/drivers/staging/nvec/ |
| D | nvec_power.c | 64 AC, enumerator
388 case AC: in nvec_power_probe()
426 case AC: in nvec_power_remove()
|
| /kernel/linux/linux-5.10/arch/powerpc/math-emu/ |
| D | math.c | 152 #define AC 3 macro
273 case FMULS: func = fmuls; type = AC; break; in do_mathemu()
293 case FMUL: func = fmul; type = AC; break; in do_mathemu()
337 case AC: in do_mathemu()
|
| /kernel/linux/linux-5.10/Documentation/hwmon/ |
| D | dell-smm-hwmon.rst | 109 Report AC status in ``/proc/i8k``. (default: 0,
139 | | | | | | | | +--------- 9. AC status
154 the AC status since this SMM call takes a long time to execute and is
157 ``power_status=1`` parameter to insmod. If AC status is not
|
| D | bel-pfe.rst | 33 1100 Watt AC to DC power-factor-corrected (PFC) power supply.
38 3000 Watt AC/DC power-factor-corrected (PFC) and DC-DC power supply.
|
| /kernel/linux/linux-5.10/sound/ac97/ |
| D | Kconfig | 14 devices around an AC-Link.
|
| /kernel/linux/linux-5.10/sound/soc/txx9/ |
| D | Kconfig | 9 This option enables support for the AC Link Controllers in TXx9 SoC.
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | tps65217.dtsi | 19 interrupt-names = "USB", "AC";
|
| /kernel/linux/linux-5.10/sound/arm/ |
| D | Kconfig | 16 tristate "ARM PrimeCell PL041 AC Link support"
|
| /kernel/linux/linux-5.10/Documentation/firmware-guide/acpi/ |
| D | method-customizing.rst | 49 Method (\_SB_.AC._PSR, 0, NotSerialized)
51 Store ("In AC _PSR", Debug)
|
1234