Searched refs:GPR (Results 1 – 18 of 18) sorted by relevance
| /kernel/linux/linux-5.10/sound/pci/emu10k1/ |
| D | emufx.c | 1829 _volume(icode, ptr, GPR(dst), GPR(src), GPR(vol))
1831 _volume(icode, ptr, GPR(dst), EXTIN(src), GPR(vol))
1833 _volume_add(icode, ptr, GPR(dst), GPR(src), GPR(vol))
1835 _volume_add(icode, ptr, GPR(dst), EXTIN(src), GPR(vol))
1837 _volume_out(icode, ptr, EXTOUT(dst), GPR(src), GPR(vol))
1841 _SWITCH(icode, ptr, GPR(dst), GPR(src), GPR(sw))
1843 _SWITCH(icode, ptr, GPR(dst), EXTIN(src), GPR(sw))
1847 _SWITCH_NEG(icode, ptr, GPR(dst), GPR(src))
1909 OP(icode, &ptr, iMACINT0, GPR(0), C_00000000, FXBUS(FXBUS_PCM_LEFT), C_00000004); in _snd_emu10k1_init_efx()
1910 OP(icode, &ptr, iMACINT0, GPR(1), C_00000000, FXBUS(FXBUS_PCM_RIGHT), C_00000004); in _snd_emu10k1_init_efx()
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/dma/ |
| D | fsl-imx-sdma.txt | 68 - gpr : The phandle to the General Purpose Register (GPR) node.
71 reg is the GPR register offset.
72 shift is the bit position inside the GPR register.
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/ |
| D | imx-dwmac.txt | 24 encompases the GPR register, and the offset of the GPR register.
|
| /kernel/linux/linux-5.10/arch/mips/alchemy/ |
| D | Kconfig | 31 bool "Trapeze ITS GPR board"
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | fsl,imx27-pinctrl.txt | 24 Registers: GIUS (GPIO In Use), GPR (General Purpose Register)
|
| /kernel/linux/patches/linux-5.10/prebuilts/usr/include/sound/ |
| D | emu10k1.h | 76 #define GPR(x) (FXGPREGBASE + (x)) macro
|
| /kernel/linux/patches/linux-4.19/prebuilts/usr/include/sound/ |
| D | emu10k1.h | 64 #define GPR(x) (FXGPREGBASE + (x)) macro
|
| /kernel/linux/linux-5.10/include/uapi/sound/ |
| D | emu10k1.h | 100 #define GPR(x) (FXGPREGBASE + (x)) /* free GPRs: x = 0x00 - 0xff */ macro
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/bus/ |
| D | imx-weim.txt | 31 Purpose Register controller that contains WEIM CS GPR
|
| /kernel/linux/patches/linux-5.10/imx8mm_patch/patches/drivers/ |
| D | 0025_linux_drivers_irqchip.patch | 371 - * Due to hardware design failure, need to make sure GPR
377 + * Due to hardware design failure, need to make sure GPR
|
| D | 0032_linux_drivers_regulator_remoteproc_reset_rpmsg_rtc.patch | 412 + by dispmix GPR registers.
679 + * IMX Display Mix GPR reset driver
707 +/* DISPMIX GPR registers */
|
| D | 0015_linux_drivers_clk.patch | 3274 + * @gpr_id: GPR ID index to control the divider
|
| D | 0030_linux_drivers_pci_misc_nvmem_of_mtd_mmc.patch | 22020 /* Grab GPR config register range */
|
| D | 0020_linux_drivers_gpu.patch | 21323 +/* GPR reg */
|
| /kernel/linux/linux-5.10/drivers/gpu/drm/radeon/ |
| D | nid.h | 887 #define GPR(x) ((x) << 16) macro
|
| D | ni_dpm.c | 3357 GPR(ni_pi->cac_weights->gpr)); in ni_initialize_hardware_cac_manager()
|
| /kernel/linux/linux-5.10/arch/arc/ |
| D | Kconfig | 416 (also referred to as r58:r59). These can also be used by gcc as GPR so
|
| /kernel/linux/patches/linux-5.10/imx8mm_patch/patches/ |
| D | 0005_linux_include.patch | 10904 +/* GPR */
|