| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/arm/marvell/ |
| D | kirkwood.txt | 12 cpus/cpu@0 with three clocks, "cpu_clk", "ddrclk" and "powersave",
13 where the "powersave" clock is a gating clock used to switch the CPU
26 clock-names = "cpu_clk", "ddrclk", "powersave";
|
| /kernel/linux/linux-5.10/tools/testing/selftests/intel_pstate/ |
| D | run.sh | 98 cpupower frequency-set -g powersave --max=${freq}MHz >& /dev/null
102 [ $EVALUATE_ONLY -eq 0 ] && cpupower frequency-set -g powersave --max=${max_freq}MHz >& /dev/null
|
| /kernel/linux/linux-5.10/Documentation/sound/designs/ |
| D | index.rst | 14 powersave
|
| /kernel/linux/linux-5.10/arch/powerpc/platforms/pasemi/ |
| D | Makefile | 2 obj-y += setup.o pci.o time.o idle.o powersave.o iommu.o dma_lib.o misc.o
|
| /kernel/linux/linux-5.10/net/mac80211/ |
| D | pm.c | 102 sdata->u.mgd.powersave && in __ieee80211_suspend()
|
| D | Kconfig | 188 bool "Verbose powersave mode debugging"
261 bool "Verbose mesh powersave debugging"
266 powersave debugging messages (when mac80211 is taking part in a
|
| D | mlme.c | 1092 bool powersave) in ieee80211_send_nullfunc() argument
1104 if (powersave) in ieee80211_send_nullfunc()
1725 if (!mgd->powersave) in ieee80211_powersave_allowed()
4095 } else if (!local->pspolling && sdata->u.mgd.powersave) { in ieee80211_rx_mgmt_beacon()
4829 ifmgd->powersave = sdata->wdev.ps; in ieee80211_sta_setup_sdata()
5627 if (ifmgd->powersave) in ieee80211_mgd_assoc()
|
| D | ieee80211_i.h | 457 bool powersave; /* powersave requested for this iface */ member
2058 bool powersave);
|
| D | cfg.c | 2832 if (tdls_peer_found || !sdata->u.mgd.powersave) in __ieee80211_request_smps_mgd()
2861 if (enabled == sdata->u.mgd.powersave && in ieee80211_set_power_mgmt()
2865 sdata->u.mgd.powersave = enabled; in ieee80211_set_power_mgmt()
|
| D | rx.c | 4234 if (!sdata->u.mgd.powersave) in ieee80211_check_fast_rx()
|
| /kernel/linux/linux-5.10/drivers/cpufreq/ |
| D | Kconfig | 56 bool "powersave"
59 Use the CPUFreq governor 'powersave' as default. This sets
122 tristate "'powersave' governor"
|
| D | Kconfig.x86 | 142 tristate "AMD frequency sensitivity feedback powersave bias"
145 This adds AMD-specific powersave bias function to the ondemand
|
| /kernel/linux/linux-5.10/Documentation/networking/ |
| D | mac80211-auth-assoc-deauth.txt | 92 mac80211->driver: turn off powersave
|
| /kernel/linux/linux-5.10/net/wireless/ |
| D | Kconfig | 163 bool "enable powersave by default"
166 This option enables powersave mode by default.
|
| /kernel/linux/linux-5.10/drivers/net/wireless/ath/ath9k/ |
| D | channel.c | 1102 bool powersave) in ath_chanctx_send_vif_ps_frame() argument
1121 if (powersave) in ath_chanctx_send_vif_ps_frame()
1148 ath_chanctx_send_ps_frame(struct ath_softc *sc, bool powersave) in ath_chanctx_send_ps_frame() argument
1155 if (ath_chanctx_send_vif_ps_frame(sc, avp, powersave)) in ath_chanctx_send_ps_frame()
|
| /kernel/linux/linux-5.10/Documentation/admin-guide/pm/ |
| D | intel_pstate.rst | 83 For example, the ``powersave`` P-state selection algorithm provided by
84 ``intel_pstate`` is not a counterpart of the generic ``powersave`` governor
88 active mode: ``powersave`` and ``performance``. The way they both operate
134 HWP + ``powersave``
157 ``powersave`` or ``performance``, depending on the ``scaling_governor`` policy
176 ``powersave``
612 affects decisions made by the scaling governors, except for ``powersave`` and
|
| D | cpufreq.rst | 367 ``powersave``
374 ``powersave`` and whenever the ``scaling_max_freq`` or ``scaling_min_freq``
517 for the AMD frequency sensitivity powersave bias driver
521 If the AMD frequency sensitivity powersave bias driver is not loaded,
529 If the AMD frequency sensitivity powersave bias driver is loaded, the
545 the ``powersave_bias`` value, the sensitivity powersave bias driver
|
| /kernel/linux/linux-5.10/tools/power/cpupower/bench/ |
| D | README-BENCH | 29 powersave module.
|
| /kernel/linux/linux-5.10/drivers/dma/ |
| D | coh901318.c | 207 struct powersave { struct
1285 struct powersave pm;
1423 struct powersave *pm = &cohc->base->pm; in enable_powersave()
1434 struct powersave *pm = &cohc->base->pm; in disable_powersave()
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | kirkwood.dtsi | 22 clock-names = "cpu_clk", "ddrclk", "powersave";
|
| /kernel/linux/linux-5.10/Documentation/livepatch/ |
| D | shadow-vars.rst | 101 ("mac80211: fix AP powersave TX vs. wakeup race"), which added a
|
| /kernel/linux/linux-5.10/sound/drivers/ |
| D | Kconfig | 216 See Documentation/sound/designs/powersave.rst for more details.
|
| /kernel/linux/linux-5.10/Documentation/admin-guide/sysctl/ |
| D | kernel.rst | 917 powersave-nap (PPC only)
1143 range of [0:600]. This could happen for instance if a powersave mode will
|
| /kernel/linux/linux-5.10/Documentation/sound/ |
| D | alsa-configuration.rst | 1068 mode. See powersave.rst for details.
|
| /kernel/linux/linux-5.10/Documentation/admin-guide/ |
| D | kernel-parameters.txt | 3980 powersave=off [PPC] This option disables power saving features.
|