| /kernel/linux/linux-6.6/drivers/leds/ |
| D | leds-bcm6328.c | 64 * @blink_leds: blinking LEDs
65 * @blink_delay: blinking delay
136 /* Remove LED from cached HW blinking intervals */ in bcm6328_led_set()
178 "fallback to soft blinking (delay_on != delay_off)\n"); in bcm6328_blink_set()
184 "fallback to soft blinking (delay > %ums)\n", in bcm6328_blink_set()
191 * Check if any of the two configurable HW blinking intervals is in bcm6328_blink_set()
193 * 1. No LEDs assigned to the HW blinking interval. in bcm6328_blink_set()
194 * 2. Only this LED is assigned to the HW blinking interval. in bcm6328_blink_set()
202 /* Add LED to the first HW blinking interval cache */ in bcm6328_blink_set()
205 /* Remove LED from the second HW blinking interval cache */ in bcm6328_blink_set()
[all …]
|
| D | leds-pca963x.c | 14 * Note that hardware blinking violates the leds infrastructure driver
15 * interface since the hardware only supports blinking all LEDs with the
19 * that is set to blink will be used for all of the blinking LEDs.
20 * Hardware blinking is disabled by default but can be enabled by setting
44 #define PCA963X_MODE2_DMBLNK 0x20 /* Enable blinking */
104 bool blinking; member
133 if (led->blinking) { in pca963x_brightness()
147 led->blinking = false; in pca963x_brightness()
157 if (led->blinking) in pca963x_brightness()
198 led->blinking = true; in pca963x_blink()
[all …]
|
| D | leds-ss4200.c | 172 * There are two gpio ports, one for blinking and the other
173 * for power. @port tells us if we're doing blinking or
227 * consistency so that both the "turn off blinking" in nasgpio_led_set_brightness()
439 * LED_OFF implies disabling future blinking in set_power_light_amber_noblink()
451 int blinking = 0; in blink_show() local
453 blinking = 1; in blink_show()
454 return sprintf(buf, "%u\n", blinking); in blink_show()
535 * light blue and blinking. This will turn it solid in nas_gpio_init()
|
| D | leds-gpio.c | 26 u8 blinking; member
47 if (led_dat->blinking) { in gpio_led_set()
50 led_dat->blinking = 0; in gpio_led_set()
71 led_dat->blinking = 1; in gpio_blink_set()
90 led_dat->blinking = 0; in create_gpio_led()
|
| /kernel/linux/linux-5.10/drivers/leds/ |
| D | leds-bcm6328.c | 64 * @blink_leds: blinking LEDs
65 * @blink_delay: blinking delay
136 /* Remove LED from cached HW blinking intervals */ in bcm6328_led_set()
178 "fallback to soft blinking (delay_on != delay_off)\n"); in bcm6328_blink_set()
184 "fallback to soft blinking (delay > %ums)\n", in bcm6328_blink_set()
191 * Check if any of the two configurable HW blinking intervals is in bcm6328_blink_set()
193 * 1. No LEDs assigned to the HW blinking interval. in bcm6328_blink_set()
194 * 2. Only this LED is assigned to the HW blinking interval. in bcm6328_blink_set()
202 /* Add LED to the first HW blinking interval cache */ in bcm6328_blink_set()
205 /* Remove LED from the second HW blinking interval cache */ in bcm6328_blink_set()
[all …]
|
| D | leds-ss4200.c | 172 * There are two gpio ports, one for blinking and the other
173 * for power. @port tells us if we're doing blinking or
227 * consistency so that both the "turn off blinking" in nasgpio_led_set_brightness()
436 * LED_OFF implies disabling future blinking in set_power_light_amber_noblink()
448 int blinking = 0; in nas_led_blink_show() local
450 blinking = 1; in nas_led_blink_show()
451 return sprintf(buf, "%u\n", blinking); in nas_led_blink_show()
536 * light blue and blinking. This will turn it solid in nas_gpio_init()
|
| D | leds-gpio.c | 24 u8 blinking; member
45 if (led_dat->blinking) { in gpio_led_set()
48 led_dat->blinking = 0; in gpio_led_set()
69 led_dat->blinking = 1; in gpio_blink_set()
87 led_dat->blinking = 0; in create_gpio_led()
|
| D | leds-pca963x.c | 14 * Note that hardware blinking violates the leds infrastructure driver
15 * interface since the hardware only supports blinking all LEDs with the
19 * that is set to blink will be used for all of the blinking LEDs.
20 * Hardware blinking is disabled by default but can be enabled by setting
44 #define PCA963X_MODE2_DMBLNK 0x20 /* Enable blinking */
|
| /kernel/linux/linux-6.6/Documentation/admin-guide/ |
| D | vga-softcursor.rst | 9 tricks: you can make your cursor look like a non-blinking red block,
40 on highlight (or sometimes blinking -- it depends on the configuration
52 To get normal blinking underline, use::
56 To get blinking block, use::
60 To get red non-blinking block, use::
|
| /kernel/linux/linux-5.10/Documentation/admin-guide/ |
| D | vga-softcursor.rst | 9 tricks: you can make your cursor look like a non-blinking red block,
40 on highlight (or sometimes blinking -- it depends on the configuration
52 To get normal blinking underline, use::
56 To get blinking block, use::
60 To get red non-blinking block, use::
|
| /kernel/linux/linux-6.6/Documentation/leds/ |
| D | leds-cht-wcove.rst | 35 This is just like how blinking works in the LED subsystem,
36 for both sw and hw blinking the brightness can also be changed
37 while blinking. Breathing on this hw really is just a variant
38 mode of blinking.
|
| D | leds-class.rst | 126 blinking,
132 blinking, returns -EBUSY if software blink fallback is enabled.
155 blink_set() function (see <linux/leds.h>). To set an LED to blinking,
159 To turn off blinking, use the API function led_brightness_set()
161 timers that may have been required for blinking.
163 The blink_set() function should choose a user friendly blinking value
170 hardware blinking function, if any.
229 device for the trigger as the source for blinking
|
| D | ledtrig-oneshot.rst | 13 event, while in the latter it keeps blinking at constant rate, as to signal
40 echo 1 > shot # led starts blinking, ignored if already blinking
|
| D | leds-lp55xx.rst | 90 For example, run blinking pattern in engine #1 of LP5521::
98 For example, run blinking pattern in engine #3 of LP55231
109 To start blinking patterns in engine #2 and #3 simultaneously::
192 /* mode_1: blinking data */
219 echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
|
| /kernel/linux/linux-5.10/Documentation/leds/ |
| D | leds-class.rst | 126 blinking,
132 blinking, returns -EBUSY if software blink fallback is enabled.
155 blink_set() function (see <linux/leds.h>). To set an LED to blinking,
159 To turn off blinking, use the API function led_brightness_set()
161 timers that may have been required for blinking.
163 The blink_set() function should choose a user friendly blinking value
170 hardware blinking function, if any.
|
| D | ledtrig-oneshot.rst | 13 event, while in the latter it keeps blinking at constant rate, as to signal
40 echo 1 > shot # led starts blinking, ignored if already blinking
|
| D | leds-lp55xx.rst | 90 For example, run blinking pattern in engine #1 of LP5521::
98 For example, run blinking pattern in engine #3 of LP55231
109 To start blinking patterns in engine #2 and #3 simultaneously::
192 /* mode_1: blinking data */
219 echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
|
| /kernel/linux/linux-5.10/drivers/staging/rtl8188eu/include/ |
| D | rtw_led.h | 51 enum LED_STATE_871x BlinkingLedState; /* Next state for blinking,
57 u8 bLedBlinkInProgress; /* true if it is blinking, false o.w.. */
61 u32 BlinkTimes; /* Number of times to toggle led state for blinking. */
63 struct timer_list BlinkTimer; /* Timer object for led blinking. */
|
| /kernel/linux/linux-6.6/include/linux/ |
| D | leds.h | 128 /* Brightness off also disables hw-blinking so it is a separate action */
153 * Deactivate blinking again when the brightness is set to LED_OFF
321 * led_blink_set - set blinking with software fallback
322 * @led_cdev: the LED to start blinking
328 * software blinking if there is no hardware blinking or if
333 * Note that if software blinking is active, simply calling
334 * led_cdev->brightness_set() will not stop the blinking,
341 * led_blink_set_nosleep - set blinking, guaranteed to not sleep
342 * @led_cdev: the LED to start blinking
354 * @led_cdev: the LED to start blinking
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/leds/ |
| D | leds-el15203000.txt | 6 The board manages 3 LEDs and supports predefined blinking patterns
10 Doesn't have any hardware blinking pattern.
13 encoded with symbol 'S' (hex code 0x53). Supports blinking breathing pattern.
|
| D | pca963x.txt | 9 - nxp,hw-blink : use hardware blinking instead of software blinking
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/leds/ |
| D | leds-el15203000.txt | 6 The board manages 3 LEDs and supports predefined blinking patterns
10 Doesn't have any hardware blinking pattern.
13 encoded with symbol 'S' (hex code 0x53). Supports blinking breathing pattern.
|
| D | pca963x.txt | 9 - nxp,hw-blink : use hardware blinking instead of software blinking
|
| /kernel/linux/linux-5.10/include/linux/ |
| D | leds.h | 113 * Deactivate blinking again when the brightness is set to LED_OFF
214 * led_blink_set - set blinking with software fallback
215 * @led_cdev: the LED to start blinking
221 * software blinking if there is no hardware blinking or if
224 * Note that if software blinking is active, simply calling
225 * led_cdev->brightness_set() will not stop the blinking,
232 * @led_cdev: the LED to start blinking
253 * software blink timer that implements blinking when the
|
| /kernel/linux/linux-5.10/drivers/staging/rtl8712/ |
| D | rtl871x_led.h | 82 u8 bLedBlinkInProgress; /*true if blinking */
89 u32 BlinkingLedState; /* Next state for blinking,
93 struct timer_list BlinkTimer; /* Timer object for led blinking.*/
|