Lines Matching +full:on +full:- +full:module
1 # SPDX-License-Identifier: GPL-2.0-only
18 depends on MFD_88PM860X
23 To compile this driver as a module, choose M here: the module
28 depends on MFD_88PM800
33 To compile this driver as a module, choose M here: the module
38 depends on AB8500_CORE
40 Say Y here to use the PowerOn Key for ST-Ericsson's AB8500
41 Mix-Sig PMIC.
43 To compile this driver as a module, choose M here: the module
44 will be called ab8500-ponkey.
53 To compile this driver as a module, choose M here: the
54 module will be called ad714x.
58 depends on INPUT_AD714X && I2C
63 To compile this driver as a module, choose M here: the
64 module will be called ad714x-i2c.
68 depends on INPUT_AD714X && SPI
73 To compile this driver as a module, choose M here: the
74 module will be called ad714x-spi.
78 depends on MFD_ARIZONA && SND_SOC
81 Say Y to enable support for the haptics module in Arizona CODECs.
83 To compile this driver as a module, choose M here: the
84 module will be called arizona-haptics.
88 depends on OF || COMPILE_TEST
89 depends on I2C
94 MCU running firmware based on Qtouch library.
97 To compile this driver as a module, choose M here: the
98 module will be called atmel_captouch.
102 depends on I2C
107 To compile this driver as a module, choose M here: the
108 module will be called bma150.
117 To compile this driver as a module, choose M here: the
118 module will be called e3x0_button.
122 depends on PCSPKR_PLATFORM
129 To compile this driver as a module, choose M here: the
130 module will be called pcspkr.
134 depends on MFD_SPMI_PMIC
137 on boards using a Qualcomm PM8941 compatible PMIC.
141 To compile this driver as a module, choose M here: the module
142 will be called pm8941-pwrkey.
146 depends on MFD_PM8XXX || MFD_SPMI_PMIC
150 on Qualcomm PM8xxx chip. This driver supports ff-memless interface
153 To compile this driver as module, choose M here: the
154 module will be called pm8xxx-vibrator.
158 depends on MFD_PM8XXX
164 To compile this driver as a module, choose M here: the
165 module will be called pmic8xxx-pwrkey.
169 depends on PCI && SPARC64
171 Say Y here if you want the standard Speaker on Sparc PCI systems
176 To compile this driver as a module, choose M here: the
177 module will be called sparcspkr.
181 depends on M68K
185 depends on MFD_MAX77650
189 To compile this driver as a module, choose M here: the module
190 will be called max77650-onkey.
194 depends on (MFD_MAX77693 || MFD_MAX77843) && PWM
197 This option enables support for the haptic controller on
200 To compile this driver as module, choose M here: the
201 module will be called max77693-haptic.
205 depends on MFD_MAX8925
210 To compile this driver as a module, choose M here: the module
215 depends on PWM && MFD_MAX8997
219 on MAXIM MAX8997 chip. This driver supports ff-memless interface
222 To compile this driver as module, choose M here: the
223 module will be called max8997-haptic.
226 tristate "MC13783 ON buttons"
227 depends on MFD_MC13XXX
229 Support the ON buttons of MC13783 PMIC as an input device
232 To compile this driver as a module, choose M here: the module
233 will be called mc13783-pwrbutton.
236 tristate "MMA8450 - Freescale's 3-Axis, 8/12-bit Digital Accelerometer"
237 depends on I2C
242 To compile this driver as a module, choose M here: the
243 module will be called mma8450.
247 depends on X86 && I2C && LEDS_CLASS
250 Say Y here for support of the Application Panel buttons, used on
255 To compile this driver as a module, choose M here: the module will
260 depends on GPIOLIB || COMPILE_TEST
264 To compile this driver as a module, choose M here: the
265 module will be called gpio-beeper.
269 depends on GPIOLIB || COMPILE_TEST
275 To compile this driver as a module, choose M here: the module
280 depends on GPIOLIB || COMPILE_TEST
287 To compile this driver as a module, choose M here: the module will be
288 called gpio-vibra.
292 depends on ARCH_IXP4XX
299 To compile this driver as a module, choose M here: the
300 module will be called ixp4xx-beeper.
304 depends on MIPS_COBALT
308 To compile this driver as a module, choose M here: the
309 module will be called cobalt_btns.
313 depends on MFD_CPCAP
318 To compile this driver as a module, choose M here. The module will
319 be called cpcap-pwrbutton.
323 depends on X86_32
329 Say Y here for support of Wistron laptop button interfaces, used on
330 laptops of various brands, including Acer and Fujitsu-Siemens. If
333 To compile this driver as a module, choose M here: the module will
338 depends on X86 && ACPI
343 To compile this driver as a module, choose M here: the module will
348 depends on USB_ARCH_HAS_HCD
353 ATI Remote Wonder II comes with some ATI's All-In-Wonder video cards
358 To compile this driver as a module, choose M here: the module will be
363 depends on USB_ARCH_HAS_HCD
367 Currently only the UIA-11 type of receiver has been tested. The tag
368 on the receiver that connects to the USB port should have a P/N that
369 will tell you what type of DMR you have. The UIA-10 type is not
373 To compile this driver as a module, choose M here: the module will
377 tristate "Kionix KXTJ9 tri-axis digital accelerometer"
378 depends on I2C
380 Say Y here to enable support for the Kionix KXTJ9 digital tri-axis
383 To compile this driver as a module, choose M here: the module will
388 depends on USB_ARCH_HAS_HCD
399 To compile this driver as a module, choose M here: the
400 module will be called powermate.
403 tristate "Yealink usb-p1k voip phone"
404 depends on USB_ARCH_HAS_HCD
408 Yealink usb-p1k usb phones. The audio part is enabled by the generic
414 To compile this driver as a module, choose M here: the module will be
418 tristate "C-Media CM109 USB I/O Controller"
419 depends on USB_ARCH_HAS_HCD
423 C-Media CM109 usb phones. The audio part is enabled by the generic
426 To compile this driver as a module, choose M here: the module will be
431 depends on REGULATOR
435 by a regulator. This driver supports ff-memless interface
438 To compile this driver as a module, choose M here: the
439 module will be called regulator-haptic.
443 depends on MFD_RETU
448 To compile this driver as a module, choose M here. The module will
449 be called retu-pwrbutton.
453 depends on (MFD_TPS65217 || MFD_TPS65218)
458 To compile this driver as a module, choose M here. The module will
459 be called tps65218-pwrbutton.
462 tristate "X-Powers AXP20X power button driver"
463 depends on MFD_AXP20X
468 To compile this driver as a module, choose M here. The module will
469 be called axp20x-pek.
474 depends on TWL4030_CORE
479 To compile this driver as a module, choose M here. The module will
484 depends on TWL4030_CORE
490 To compile this driver as a module, choose M here. The module will
495 depends on TWL6040_CORE
500 To compile this driver as a module, choose M here. The module will
507 subsystem accessible under char device 10:223 - /dev/input/uinput.
509 To compile this driver as a module, choose M here: the
510 module will be called uinput.
514 depends on SGI_IP22 || SGI_IP32
518 To compile this driver as a module, choose M here: the
519 module will be called sgi_btns.
523 depends on (GSC || HP300) && SERIO
526 Say Y here if you want to support the built-in real time clock
531 depends on MFD_PALMAS
536 To compile this driver as a module, choose M here. The module will
541 depends on MFD_PCF50633
544 layer on NXP PCF50633.
548 depends on I2C
553 To compile this driver as a module, choose M here: the
554 module will be called pcf8574_keypad.
558 depends on PWM
564 To compile this driver as a module, choose M here: the module will be
565 called pwm-beeper.
569 depends on PWM
576 To compile this driver as a module, choose M here: the module will be
577 called pwm-vibra.
581 depends on MFD_RK808
587 To compile this driver as a module, choose M here: the module will be
592 depends on GPIOLIB || COMPILE_TEST
595 Check file:Documentation/input/devices/rotary-encoder.rst for more
598 To compile this driver as a module, choose M here: the
599 module will be called rotary_encoder.
603 depends on MIKROTIK_RB532
604 depends on GPIOLIB
609 To compile this driver as a module, choose M here: the
610 module will be called rb532_button.
614 depends on PMIC_DA9052
619 To compile this driver as a module, choose M here: the
620 module will be called da9052_onkey.
624 depends on MFD_DA9055
629 To compile this driver as a module, choose M here: the module
634 depends on MFD_DA9063 || MFD_DA9062
640 To compile this driver as a module, choose M here: the module
645 depends on MFD_DM355EVM_MSP
651 To compile this driver as a module, choose M here: the
652 module will be called dm355evm_keys.
655 tristate "WM831X ON pin"
656 depends on MFD_WM831X
658 Support the ON pin of WM831X PMICs as an input device
661 To compile this driver as a module, choose M here: the module
666 depends on EZX_PCAP
669 on Motorola EZX phones.
671 To compile this driver as a module, choose M here: the
672 module will be called pcap_keys.
675 tristate "Analog Devices ADXL34x Three-Axis Digital Accelerometer"
679 ADXL345/6 controller, and your board-specific initialization
688 To compile this driver as a module, choose M here: the
689 module will be called adxl34x.
693 depends on INPUT_ADXL34X && I2C
698 To compile this driver as a module, choose M here: the
699 module will be called adxl34x-i2c.
703 depends on INPUT_ADXL34X && SPI
708 To compile this driver as a module, choose M here: the
709 module will be called adxl34x-spi.
713 depends on USB
714 depends on LEDS_CLASS
718 To compile this driver as a module, choose M here: the module will be
723 depends on I2C
729 To compile this driver as a module, choose M here: the
730 module will be called iqs269a.
733 tristate "VTI CMA3000 Tri-axis accelerometer"
743 To compile this driver as a module, choose M here: the
744 module will be called cma3000_d0x.
748 depends on INPUT_CMA3000 && I2C
753 To compile this driver as a module, choose M here: the
754 module will be called cma3000_d0x_i2c.
758 depends on XEN
762 This driver implements the front-end of the Xen virtual
763 keyboard and mouse device driver. It communicates with a back-end
766 To compile this driver as a module, choose M here: the
767 module will be called xen-kbdfront.
770 tristate "CSR SiRFSoC power on/off/suspend key support"
771 depends on ARCH_SIRF && OF
774 Say Y here if you want to support for the SiRFSoC power on/off/suspend key
781 depends on INPUT
782 depends on SERIO_I8042
786 To compile this driver as a module, choose M here: the
787 module will be called ideapad_slidebar.
790 tristate "Windows-compatible SoC Button Array"
791 depends on KEYBOARD_GPIO && ACPI
793 Say Y here if you have a SoC-based tablet that originally runs
796 To compile this driver as a module, choose M here: the
797 module will be called soc_button_array.
801 depends on INPUT && I2C
802 depends on GPIOLIB || COMPILE_TEST
808 To compile this driver as a module, choose M here: the
809 module will be called drv260x-haptics.
813 depends on INPUT && I2C
819 To compile this driver as a module, choose M here: the
820 module will be called drv2665-haptics.
824 depends on INPUT && I2C
830 To compile this driver as a module, choose M here: the
831 module will be called drv2667-haptics.
835 depends on ARCH_HISI || COMPILE_TEST
839 To compile this driver as a module, choose M here: the
840 module will be called hisi_powerkey.
844 depends on RAVE_SP_CORE
848 To compile this driver as a module, choose M here: the
849 module will be called rave-sp-pwrbutton.
853 depends on MFD_SC27XX_PMIC || COMPILE_TEST
858 To compile this driver as a module, choose M here. The module will
863 depends on MFD_STPMIC1
866 can be used to wakeup from low power modes and force a shut-down on
869 To compile this driver as a module, choose M here: the
870 module will be called stpmic1_onkey.