Lines Matching +full:force +full:- +full:load +full:- +full:on +full:- +full:access
1 .TH sane\-mustek 5 "13 Jul 2008" "@PACKAGEVERSION@" "SANE Scanner Access Now Easy"
2 .IX sane\-mustek
4 sane\-mustek \- SANE backend for Mustek SCSI flatbed scanners (and some other devices)
7 .B sane\-mustek
8 library implements a SANE (Scanner Access Now Easy) backend that provides access
14 Paragon MFS-6000CX
16 Paragon MFS-12000CX
18 Paragon MFC-600S, 600 II CD, ScanMagic 600 II SP
20 Paragon MFC-800S, 800 II SP
22 Paragon MFS-6000SP
24 Paragon MFS-8000SP
26 Paragon MFS-1200SP, MFS-12000SP
56 More details can be found on the Mustek SCSI backend homepage
57 .IR http://www.meier\-geinitz.de/sane/mustek\-backend/ .
63 non-SCSI scanners that have some support at this point is the 600 II N and 600
68 too. More info on how to use these parallel port scanners can be found below in
95 .IR sane\-devel@alioth-lists.debian.net .
99 .IR "scanimage \-L" .
100 Please send all of it to the mailing list. You must be subscribed to sane\-devel
102 .I http://www.sane\-project.org/mailing\-lists.html
114 is either the path-name for the special device that corresponds to a
156 .B linedistance\-fix
160 likely that your controller suffers from this problem. Turning on
164 .B lineart\-fix
166 with certain MFS-12000SP scanners. The problem manifests itself in
167 dropped lines when scanning in lineart mode. Turning on this option
171 .B legal\-size
197 .B strip\-height
200 fractional part (e.g., 1.5). Setting the strip\-height to a small value (one
202 driver timeouts and/or timeouts with other devices on the same SCSI bus.
207 .B disable\-double\-buffering
214 .B disable\-backtracking
222 .B force\-wait
224 before sending the inquiry command. Further more the backend will force the
235 option strip\-height 1.5
246 # turn on fixes for /dev/sge:
248 option lineart\-fix
250 option linedistance\-fix
263 so much load on the system, that it becomes almost unusable for other tasks.
266 should consider that Mustek scanners do not support the SCSI-2
268 scan is in progress. This means that no other SCSI device on the same
271 Because the Mustek-supplied adapter is not worth much and because
272 Mustek scanners do not support the SCSI-2 disconnect/reconnect
277 For Mustek scanners, it is typically necessary to configure the low-level SCSI
281 for driver- and platform-specific information.
288 Details on how to get the Mustek SCSI adapters and other cards running can be
290 .IR http://www.meier\-geinitz.de/sane/mustek\-backend/#SCSI .
306 only one number on a single line. Example:
312 Note that for these scanners usually root privileges are required to access the
318 access this backend through the network daemon
323 .B force\-wait
331 you use the scanner again, the lamp turns back on to the normal high
333 have stripes and appear to be over-exposed. When this happens, just
343 .I @LIBDIR@/libsane\-mustek.a
346 .I @LIBDIR@/libsane\-mustek.so
347 The shared library implementing this backend (present on systems that
354 contain the configuration file. On *NIX systems, the directories are
356 semi-colon (`;'). If this variable is not set, the configuration file
383 3 print non-fatal errors and less important messages
407 .I http://www.meier\-geinitz.de/sane/mustek\-backend/
411 Henning Meier-Geinitz, James Perry (600 II EP).
423 .IR http://www.meier\-geinitz.de/sane/mustek\-backend/ .