| /kernel/linux/linux-5.10/drivers/net/can/sja1000/ |
| D | tscan1.c | 3 * tscan1.c: driver for Technologic Systems TS-CAN1 PC104 boards
10 * - Getting started with TS-CAN1, Technologic Systems, Jun 2009
11 * http://www.embeddedarm.com/documentation/ts-can1-manual.pdf
22 MODULE_DESCRIPTION("Driver for Technologic Systems TS-CAN1 PC104 boards");
78 /* Probe for a TS-CAN1 board with JP2:JP1 jumper setting ID */
145 netdev_info(netdev, "TS-CAN1 at 0x%lx 0x%lx irq %d\n", in tscan1_probe()
|
| /kernel/linux/linux-6.6/drivers/net/can/sja1000/ |
| D | tscan1.c | 3 * tscan1.c: driver for Technologic Systems TS-CAN1 PC104 boards
9 * - Getting started with TS-CAN1, Technologic Systems, Feb 2022
10 * https://docs.embeddedts.com/TS-CAN1
21 MODULE_DESCRIPTION("Driver for Technologic Systems TS-CAN1 PC104 boards");
77 /* Probe for a TS-CAN1 board with JP2:JP1 jumper setting ID */
144 netdev_info(netdev, "TS-CAN1 at 0x%lx 0x%lx irq %d\n", in tscan1_probe()
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/net/can/ |
| D | st,stm32-bxcan.yaml | 69 SRAM memory shared by the two bxCAN cells (CAN1 primary and CAN2
87 can1: can@40006400 {
92 resets = <&rcc STM32F4_APB1_RESET(CAN1)>;
93 clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN1)>;
|
| D | renesas,rcar-canfd.yaml | 125 - description: CAN1 error interrupt
126 - description: CAN1 transmit interrupt
127 - description: CAN1 transmit/receive FIFO receive completion interrupt
|
| /kernel/linux/linux-5.10/arch/arm64/boot/dts/renesas/ |
| D | cat875.dtsi | 38 &can1 {
61 can1_pins: can1 {
63 function = "can1";
|
| D | hihope-rzg2-ex.dtsi | 40 &can1 {
77 can1_pins: can1 {
79 function = "can1";
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/renesas/ |
| D | cat875.dtsi | 40 &can1 {
63 can1_pins: can1 {
65 function = "can1";
|
| D | hihope-rzg2-ex.dtsi | 42 &can1 {
79 can1_pins: can1 {
81 function = "can1";
|
| D | rzg2lc-smarc-pinfunction.dtsi | 17 can1_pins: can1 {
25 can1-stb-hog {
32 can1_pins: can1 {
|
| D | r9a07g044c2-smarc.dts | 14 * SW1-3 : SW_SCIF_CAN (1: CAN1; 0: SCIF1)
15 * SW1-4 : SW_RSPI_CAN (1: CAN1; 0: RSPI1)
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/renesas/ |
| D | iwg20d-q7-dbcm-ca.dtsi | 32 &can1 {
98 can1_pins: can1 {
100 function = "can1";
|
| D | r8a7745-iwg22d-sodimm-dbhd-ca.dts | 54 &can1 {
116 can1_pins: can1 {
118 function = "can1";
|
| D | r9a06g032-rzn1d400-db.dts | 33 /* Assuming CN10/CN11 are wired for CAN1 */
37 &can1 {
41 /* Please only enable can0 or can1, depending on CN10/CN11 */
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | iwg20d-q7-dbcm-ca.dtsi | 32 &can1 {
98 can1_pins: can1 {
100 function = "can1";
|
| D | r8a7745-iwg22d-sodimm-dbhd-ca.dts | 54 &can1 {
116 can1_pins: can1 {
118 function = "can1";
|
| D | at91sam9x5_can.dtsi | 26 can1: can@f8004000 { label
46 can1 {
|
| D | sama5d3_can.dtsi | 24 can1 {
45 can1: can@f8010000 { label
|
| /kernel/linux/linux-5.10/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp-zc1751-xm016-dc2.dts | 22 can1 = &can1;
47 &can1 {
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/nxp/imx/ |
| D | imx6qdl-skov-cpu.dtsi | 14 can0 = &can1;
15 can1 = &can2;
133 reg_can1_stby: regulator-can1-stby {
137 regulator-name = "can1-3v3";
194 &can1 {
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/reset/ |
| D | zynq-reset.txt | 46 257: can1 reset
48 259: can1 ref reset
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/reset/ |
| D | zynq-reset.txt | 46 257: can1 reset
48 259: can1 ref reset
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/microchip/ |
| D | at91sam9x5_can.dtsi | 26 can1: can@f8004000 { label
46 can1 {
|
| D | sama5d3_can.dtsi | 24 can1 {
45 can1: can@f8010000 { label
|
| /kernel/linux/linux-5.10/arch/powerpc/boot/dts/fsl/ |
| D | p1010si-pre.dtsi | 54 can1 = &can1;
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/pinctrl/ |
| D | loongson,ls2k-pinctrl.yaml | 42 enum: [gpio, sdio, can1, can0, pwm3, pwm2, pwm1, pwm0, i2c1, i2c0,
47 enum: [gpio, sdio, can1, can0, pwm3, pwm2, pwm1, pwm0, i2c1, i2c0,
|