Home
last modified time | relevance | path

Searched full:gusb2phycfg (Results 1 – 13 of 13) sorted by relevance

/kernel/linux/linux-6.6/drivers/usb/dwc3/
Ddebugfs.c95 dump_register(GUSB2PHYCFG(0)),
96 dump_register(GUSB2PHYCFG(1)),
97 dump_register(GUSB2PHYCFG(2)),
98 dump_register(GUSB2PHYCFG(3)),
99 dump_register(GUSB2PHYCFG(4)),
100 dump_register(GUSB2PHYCFG(5)),
101 dump_register(GUSB2PHYCFG(6)),
102 dump_register(GUSB2PHYCFG(7)),
103 dump_register(GUSB2PHYCFG(8)),
104 dump_register(GUSB2PHYCFG(9)),
[all …]
Ddrd.c230 /* GUSB2PHYCFG.ULPIAutoRes = 1/0, GUSB2PHYCFG.SusPHY = 1 */ in dwc3_otg_host_init()
293 /* GUSB2PHYCFG.ULPIAutoRes = 0, GUSB2PHYCFG0.SusPHY = 1 */ in dwc3_otg_device_init()
Dcore.c137 * GUSB2PHYCFG.SUSPHY should be cleared during mode switching, in dwc3_set_prtcap()
732 /* Ensure the GUSB2PHYCFG.SUSPHY is cleared prior to phy init. */ in dwc3_phy_setup()
747 * ULPIEXTVBUSDRV bit[17] of the GUSB2PHYCFG register to drive vBus in dwc3_phy_setup()
816 * Make sure GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY are clear in dwc3_phy_power_on()
821 * GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid in dwc3_phy_power_on()
2222 /* Restore GUSB2PHYCFG bits that were modified in suspend */ in dwc3_resume_common()
Dgadget.c300 * GUSB2PHYCFG.SUSPENDUSB2, which turns on the signal required to complete
321 * When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or in dwc3_send_gadget_ep_cmd()
322 * GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an in dwc3_send_gadget_ep_cmd()
325 * Save and clear both GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY in dwc3_send_gadget_ep_cmd()
2636 * GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting in dwc3_gadget_run_stop()
Dcore.h1103 * @dis_enblslpm_quirk: set if we clear enblslpm in GUSB2PHYCFG,
1111 * in GUSB2PHYCFG, specify that USB2 PHY doesn't
/kernel/linux/linux-5.10/drivers/usb/dwc3/
Ddebugfs.c92 dump_register(GUSB2PHYCFG(0)),
93 dump_register(GUSB2PHYCFG(1)),
94 dump_register(GUSB2PHYCFG(2)),
95 dump_register(GUSB2PHYCFG(3)),
96 dump_register(GUSB2PHYCFG(4)),
97 dump_register(GUSB2PHYCFG(5)),
98 dump_register(GUSB2PHYCFG(6)),
99 dump_register(GUSB2PHYCFG(7)),
100 dump_register(GUSB2PHYCFG(8)),
101 dump_register(GUSB2PHYCFG(9)),
[all …]
Ddrd.c230 /* GUSB2PHYCFG.ULPIAutoRes = 1/0, GUSB2PHYCFG.SusPHY = 1 */ in dwc3_otg_host_init()
293 /* GUSB2PHYCFG.ULPIAutoRes = 0, GUSB2PHYCFG0.SusPHY = 1 */ in dwc3_otg_device_init()
Dcore.h1041 * @dis_enblslpm_quirk: set if we clear enblslpm in GUSB2PHYCFG,
1047 * in GUSB2PHYCFG, specify that USB2 PHY doesn't
Dcore.c727 * For DRD controllers, GUSB2PHYCFG.SUSPHY must be cleared after in dwc3_phy_setup()
1787 /* Restore GUSB2PHYCFG bits that were modified in suspend */ in dwc3_resume_common()
Dgadget.c286 * When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or in dwc3_send_gadget_ep_cmd()
287 * GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an in dwc3_send_gadget_ep_cmd()
290 * Save and clear both GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY in dwc3_send_gadget_ep_cmd()
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/usb/
Ddwc3.txt64 - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
71 in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/usb/
Dsnps,dwc3.yaml202 When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal
221 When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2
/kernel/linux/linux-6.6/drivers/phy/broadcom/
Dphy-brcm-usb-init-synopsys.c156 USB_XHCI_GBL_UNSET(xhci_gbl, GUSB2PHYCFG, U2_FREECLK_EXISTS); in xhci_soft_reset()