| /kernel/linux/linux-5.10/arch/mips/pci/ |
| D | fixup-capcella.c | 15 #define INT1 RTL8139_1_IRQ macro
23 [11] = { -1, INT1, INT1, INT1, INT1 },
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/iio/accel/ |
| D | fsl,mma7455.yaml | 32 Data ready is only available on INT1, but events can use either or
34 to INT1 and second (where present) to INT2.
39 - INT1
64 interrupt-names = "INT2", "INT1";
79 interrupt-names = "INT1";
|
| D | bosch,bma255.yaml | 50 connected to the INT1 pin, the second (optional) interrupt listed must be
54 BMC156 does not have an INT1 pin, therefore the first interrupt pin is
62 - INT1
92 interrupt-names = "INT1";
|
| D | nxp,fxls8962af.yaml | 35 - INT1
63 interrupt-names = "INT1";
79 interrupt-names = "INT1";
|
| D | adi,adxl313.yaml | 46 - INT1
72 interrupt-names = "INT1";
89 interrupt-names = "INT1";
|
| D | kionix,kx022a.yaml | 31 - enum: [INT1, INT2]
60 interrupt-names = "INT1";
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/iio/imu/ |
| D | bosch,bmi160.yaml | 29 - INT1
32 set to "INT1" if INT1 pin should be used as interrupt input, set
72 interrupt-names = "INT1";
|
| D | nxp,fxos8700.yaml | 33 - INT1
61 interrupt-names = "INT1";
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/iio/imu/ |
| D | bosch,bmi160.yaml | 29 - INT1
32 set to "INT1" if INT1 pin should be used as interrupt input, set
73 interrupt-names = "INT1";
|
| D | nxp,fxos8700.yaml | 33 - INT1
62 interrupt-names = "INT1";
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/interrupt-controller/ |
| D | loongson,liointc.yaml | 41 - const: int1
83 interrupt-names = "int0", "int1";
86 <0x0f000000>, /* int1 */
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/interrupt-controller/ |
| D | loongson,liointc.yaml | 49 - const: int1
110 interrupt-names = "int0", "int1";
113 <0x0f000000>, /* int1 */
|
| /kernel/linux/linux-6.6/drivers/iio/common/st_sensors/ |
| D | st_sensors_core.c | 247 if (!sdata->sensor_settings->drdy_irq.int1.addr && in st_sensors_set_drdy_int_pin()
258 if (!sdata->sensor_settings->drdy_irq.int1.mask) { in st_sensors_set_drdy_int_pin()
260 "DRDY on INT1 not available.\n"); in st_sensors_set_drdy_int_pin()
279 if (!sdata->sensor_settings->drdy_irq.int1.addr_od && in st_sensors_set_drdy_int_pin()
401 addr = sdata->sensor_settings->drdy_irq.int1.addr_od; in st_sensors_init_sensor()
402 mask = sdata->sensor_settings->drdy_irq.int1.mask_od; in st_sensors_init_sensor()
429 if (!sdata->sensor_settings->drdy_irq.int1.addr && in st_sensors_set_dataready_irq()
453 drdy_addr = sdata->sensor_settings->drdy_irq.int1.addr; in st_sensors_set_dataready_irq()
454 drdy_mask = sdata->sensor_settings->drdy_irq.int1.mask; in st_sensors_set_dataready_irq()
|
| /kernel/linux/linux-5.10/drivers/iio/common/st_sensors/ |
| D | st_sensors_core.c | 275 if (!sdata->sensor_settings->drdy_irq.int1.addr && in st_sensors_set_drdy_int_pin()
286 if (!sdata->sensor_settings->drdy_irq.int1.mask) { in st_sensors_set_drdy_int_pin()
288 "DRDY on INT1 not available.\n"); in st_sensors_set_drdy_int_pin()
307 if (!sdata->sensor_settings->drdy_irq.int1.addr_od && in st_sensors_set_drdy_int_pin()
429 addr = sdata->sensor_settings->drdy_irq.int1.addr_od; in st_sensors_init_sensor()
430 mask = sdata->sensor_settings->drdy_irq.int1.mask_od; in st_sensors_init_sensor()
457 if (!sdata->sensor_settings->drdy_irq.int1.addr && in st_sensors_set_dataready_irq()
481 drdy_addr = sdata->sensor_settings->drdy_irq.int1.addr; in st_sensors_set_dataready_irq()
482 drdy_mask = sdata->sensor_settings->drdy_irq.int1.mask; in st_sensors_set_dataready_irq()
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/iio/gyroscope/ |
| D | nxp,fxas21002c.txt | 14 - interrupts : device support 2 interrupts, INT1 and INT2,
17 - interrupt-names: should contain "INT1" or "INT2", the gyroscope interrupt
|
| /kernel/linux/linux-6.6/drivers/iio/accel/ |
| D | st_accel_core.c | 180 .int1 = {
254 .int1 = {
348 .int1 = {
426 .int1 = {
489 .int1 = {
569 .int1 = {
628 .int1 = {
701 .int1 = {
774 .int1 = {
832 .int1 = {
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/ |
| D | fsl-fec.txt | 35 3 "int0", "int1", "int2"
36 4 "int0", "int1", "int2", "pps"
38 property. Currently, only i.mx7 uses "int1" and "int2". They correspond to
|
| /kernel/linux/linux-5.10/arch/mips/boot/dts/loongson/ |
| D | loongson64g-package.dtsi | 33 interrupt-names = "int0", "int1";
36 <0xff000000>, /* int1 */
|
| D | loongson64c-package.dtsi | 36 interrupt-names = "int0", "int1";
39 <0x0f000000>, /* int1 */
|
| /kernel/linux/linux-6.6/arch/mips/boot/dts/loongson/ |
| D | loongson64g-package.dtsi | 33 interrupt-names = "int0", "int1";
36 <0xff000000>, /* int1 */
|
| D | loongson64c-package.dtsi | 36 interrupt-names = "int0", "int1";
39 <0x0f000000>, /* int1 */
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | stm32mp153.dtsi | 32 interrupt-names = "int0", "int1";
45 interrupt-names = "int0", "int1";
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/st/ |
| D | stm32mp153.dtsi | 39 interrupt-names = "int0", "int1";
52 interrupt-names = "int0", "int1";
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/iio/gyroscope/ |
| D | nxp,fxas21002c.yaml | 43 - INT1
81 interrupt-names = "INT1";
|
| /kernel/linux/linux-5.10/drivers/iio/accel/ |
| D | st_accel_core.c | 161 .int1 = {
235 .int1 = {
329 .int1 = {
407 .int1 = {
469 .int1 = {
548 .int1 = {
607 .int1 = {
680 .int1 = {
753 .int1 = {
811 .int1 = {
[all …]
|