| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/soc/ti/ |
| D | wkup-m3-ipc.yaml | 27 Support for VTT Toggle with GPIO pin
30 connected to the enable pin on the DDR VTT regulator. This allows the
80 ti,vtt-gpio-pin:
82 description: GPIO pin connected to enable pin on VTT regulator
129 ti,vtt-gpio-pin = <7>;
137 * On the AM437x-GP-EVM board, gpio5_7 is wired to enable pin of the DDR VTT
140 * state of the pin is configured for pull-down and thus the VTT regulator
142 * this method is an alternative to using the 'ti,vtt-gpio-pin' property.
|
| /kernel/linux/linux-6.6/drivers/regulator/ |
| D | tps65086-regulator.c | 18 LDOA2, LDOA3, VTT, SWA1, SWB1, SWB2 }; enumerator
171 TPS65086_SWITCH("VTT", "vtt", VTT, TPS65086_SWVTT_EN, BIT(4)),
211 TPS65086_SWITCH("VTT", "vtt", VTT, TPS65086_SWVTT_EN, BIT(4)),
250 TPS65086_SWITCH("VTT", "vtt", VTT, TPS65086_SWVTT_EN, BIT(4)),
289 TPS65086_SWITCH("VTT", "vtt", VTT, TPS65086_SWVTT_EN, BIT(4)),
|
| /kernel/linux/linux-5.10/drivers/hwmon/ |
| D | abituguru3.c | 190 { "DDR VTT", 2, 0, 10, 1, 0 },
191 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
212 { "DDR VTT", 2, 0, 10, 1, 0 },
213 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
241 { "DDR VTT", 2, 0, 10, 1, 0 },
242 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
263 { "DDR VTT", 2, 0, 10, 1, 0 },
264 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
284 { "DDR VTT", 2, 0, 10, 1, 0 },
285 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
[all …]
|
| D | w83793.c | 131 {0x12, 0x64, 0x65}, /* Vtt */
141 /* Low Bits of Vcore A/B Vtt Read/High/Low */
217 u8 in_low_bits[3]; /* Additional resolution for VCore A/B Vtt */
951 /* only Vcore A/B and Vtt have additional 2 bits precision */
|
| /kernel/linux/linux-6.6/drivers/hwmon/ |
| D | abituguru3.c | 190 { "DDR VTT", 2, 0, 10, 1, 0 },
191 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
212 { "DDR VTT", 2, 0, 10, 1, 0 },
213 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
241 { "DDR VTT", 2, 0, 10, 1, 0 },
242 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
263 { "DDR VTT", 2, 0, 10, 1, 0 },
264 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
284 { "DDR VTT", 2, 0, 10, 1, 0 },
285 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
[all …]
|
| D | w83793.c | 131 {0x12, 0x64, 0x65}, /* Vtt */
141 /* Low Bits of Vcore A/B Vtt Read/High/Low */
217 u8 in_low_bits[3]; /* Additional resolution for VCore A/B Vtt */
951 /* only Vcore A/B and Vtt have additional 2 bits precision */
|
| /kernel/linux/linux-5.10/drivers/regulator/ |
| D | tps65086-regulator.c | 26 LDOA2, LDOA3, SWA1, SWB1, SWB2, VTT }; enumerator
162 TPS65086_SWITCH("VTT", "vtt", VTT, TPS65086_SWVTT_EN, BIT(4)),
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/mfd/ |
| D | ti,tps65086.yaml | 45 buck[1-6], ldoa[1-3], swa1, swb[1-2], and vtt.
73 "^(ldoa[1-3]|swa1|swb[1-2]|vtt)$":
|
| /kernel/linux/linux-5.10/Documentation/hwmon/ |
| D | w83795.rst | 51 28 VTT 1Bh in11
107 22 VTT 1Bh in11
|
| D | adt7475.rst | 109 in5 VTT (8)
|
| D | abituguru-datasheet.rst | 193 - Sensor 10 DDR Vtt volt
|
| /kernel/linux/linux-6.6/Documentation/hwmon/ |
| D | w83795.rst | 51 28 VTT 1Bh in11
107 22 VTT 1Bh in11
|
| D | adt7475.rst | 109 in5 VTT (8)
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/mfd/ |
| D | tps65086.txt | 19 ldoa[1-3], swa1, swb[1-2], and vtt. Each child
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | am335x-icev2.dts | 38 regulator-name = "vtt";
449 /* Do not idle the GPIO used for holding the VTT regulator */
|
| D | vexpress-v2p-ca9.dts | 252 /* DDR2 SDRAM VTT termination voltage */
|
| D | am57xx-beagle-x15-common.dtsi | 104 vtt_fixed: fixedregulator-vtt {
|
| D | dra76-evm.dts | 142 vtt_fixed: fixedregulator-vtt {
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/ti/omap/ |
| D | am335x-icev2.dts | 38 regulator-name = "vtt";
449 /* Do not idle the GPIO used for holding the VTT regulator */
|
| D | dra76-evm.dts | 142 vtt_fixed: fixedregulator-vtt {
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/st/ |
| D | stm32mp157a-icore-stm32mp1.dtsi | 98 vtt_ddr: regulator-vtt-ddr {
|
| /kernel/linux/linux-6.6/drivers/soc/ti/ |
| D | wkup_m3_ipc.c | 672 if (!of_property_read_u32(np, "ti,vtt-gpio-pin", &temp)) { in wkup_m3_ipc_probe()
676 dev_warn(dev, "Invalid VTT GPIO(%d) pin\n", temp); in wkup_m3_ipc_probe()
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/ti/ |
| D | k3-am654-base-board.dts | 136 regulator-name = "vtt";
159 ddr_vtt_pins_default: ddr-vtt-default-pins {
|
| D | k3-am642-evm.dts | 170 regulator-name = "vtt";
380 ddr_vtt_pins_default: ddr-vtt-default-pins {
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/arm/ |
| D | vexpress-v2p-ca9.dts | 252 /* DDR2 SDRAM VTT termination voltage */
|