Searched +full:charge +full:- +full:enable +full:- +full:gpios (Results 1 – 25 of 257) sorted by relevance
1234567891011
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/power/supply/ |
| D | bq2515x.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
6 $schema: "http://devicetree.org/meta-schemas/core.yaml#"
8 title: TI bq2515x 500-mA Linear charger family
11 - Dan Murphy <dmurphy@ti.com>
12 - Ricardo Rivera-Matos <r-rivera-matos@ti.com>
15 The BQ2515x family is a highly integrated battery charge management IC that
18 push-button controller.
27 - ti,bq25150
28 - ti,bq25155
[all …]
|
| D | max8903-charger.txt | 4 - compatible: "maxim,max8903" for MAX8903 Battery Charger
5 - dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided
6 - uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provid…
9 - cen-gpios: Charge enable pin (active low, output)
10 - chg-gpios: Charger status pin (active low, input)
11 - flt-gpios: Fault pin (active low, output)
12 - dcm-gpios: Current limit mode setting (DC=1 or USB=0, output)
13 - usus-gpios: USB suspend pin (active high, output)
18 max8903-charger {
20 dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
[all …]
|
| D | ti,bq24735.txt | 1 TI BQ24735 Charge Controller
5 - compatible : "ti,bq24735"
8 - interrupts : Specify the interrupt to be used to trigger when the AC
10 - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter
15 - ti,charge-current : Used to control and set the charging current. This value
19 - ti,charge-voltage : Used to control and set the charging voltage. This value
23 - ti,input-current : Used to control and set the charger input current. This
27 - ti,external-control : Indicates that the charger is configured externally
28 and that the host should not attempt to enable/disable charging or set the
29 charge voltage/current.
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/power/supply/ |
| D | bq2515x.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: TI bq2515x 500-mA Linear charger family
11 - Andrew Davis <afd@ti.com>
14 The BQ2515x family is a highly integrated battery charge management IC that
17 push-button controller.
26 - ti,bq25150
27 - ti,bq25155
33 ac-detect-gpios:
[all …]
|
| D | richtek,rt9467.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - ChiYuan Huang <cy_huang@richtek.com>
11 - ChiaEn Wu <chiaen_wu@richtek.com>
14 RT9467 is a switch-mode single cell Li-Ion/Li-Polymer battery charger for
16 MOSFETs, input current sensing and regulation, high-accuracy voltage
17 regulation, and charge termination. The charge current is regulated through
20 The RT9467 also features USB On-The-Go (OTG) support. It also integrates
21 D+/D- pin for USB host/charging port detection.
[all …]
|
| D | richtek,rt9471.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Alina Yu <alina_yu@richtek.com>
11 - ChiYuan Huang <cy_huang@richtek.com>
14 RT9471 is a switch-mode single cell Li-Ion/Li-Polymer battery charger for
19 https://www.richtek.com/assets/product_file/RT9471=RT9471D/DS9471D-02.pdf
28 charge-enable-gpios:
32 wakeup-source: true
37 usb-otg-vbus-regulator:
[all …]
|
| D | maxim,max8903.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
13 - $ref: power-supply.yaml#
19 dok-gpios:
23 uok-gpios:
27 cen-gpios:
29 description: Charge enable pin (active low, output)
31 chg-gpios:
[all …]
|
| D | bq24735.yaml | 1 # SPDX-License-Identifier: GPL-2.0
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: TI BQ24735 Li-Ion Battery Charger
11 - Sebastian Reichel <sre@kernel.org>
14 - $ref: power-supply.yaml#
27 ti,ac-detect-gpios:
35 ti,charge-current:
43 ti,charge-voltage:
51 ti,input-current:
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/leds/ |
| D | leds-sgm3140.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/leds-sgm3140.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: SGMICRO SGM3140 500mA Buck/Boost Charge Pump LED Driver
10 - Luca Weiss <luca@z3ntu.xyz>
13 The SGM3140 is a current-regulated charge pump which can regulate two current
17 http://www.sg-micro.com/uploads/soft/20190626/1561535688.pdf
23 enable-gpios:
27 flash-gpios:
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/leds/ |
| D | leds-sgm3140.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/leds-sgm3140.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: SGMICRO SGM3140 500mA Buck/Boost Charge Pump LED Driver
10 - Luca Weiss <luca@z3ntu.xyz>
13 The SGM3140 is a current-regulated charge pump which can regulate two current
17 http://www.sg-micro.com/uploads/soft/20190626/1561535688.pdf
22 - ocs,ocp8110
23 - richtek,rt5033-led
[all …]
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/rockchip/ |
| D | rk3566-anbernic-rg503.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 /dts-v1/;
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/linux-event-codes.h>
7 #include <dt-bindings/pinctrl/rockchip.h>
8 #include "rk3566-anbernic-rgxx3.dtsi"
21 compatible = "simple-battery";
22 charge-full-design-microamp-hours = <3472000>;
23 charge-term-current-microamp = <300000>;
24 constant-charge-current-max-microamp = <2000000>;
[all …]
|
| D | rk3566-anbernic-rg353p.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 /dts-v1/;
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/linux-event-codes.h>
7 #include <dt-bindings/pinctrl/rockchip.h>
8 #include "rk3566-anbernic-rg353x.dtsi"
22 compatible = "simple-battery";
23 charge-full-design-microamp-hours = <3472000>;
24 charge-term-current-microamp = <300000>;
25 constant-charge-current-max-microamp = <2000000>;
[all …]
|
| D | rk3566-anbernic-rg353ps.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 /dts-v1/;
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/linux-event-codes.h>
7 #include <dt-bindings/pinctrl/rockchip.h>
8 #include "rk3566-anbernic-rg353x.dtsi"
21 compatible = "simple-battery";
22 charge-full-design-microamp-hours = <3472000>;
23 charge-term-current-microamp = <300000>;
24 constant-charge-current-max-microamp = <2000000>;
[all …]
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/nxp/imx/ |
| D | imx6dl-b1x5pv2.dtsi | 1 // SPDX-License-Identifier: GPL-2.0 OR MIT
6 // Copyright 2018-2021 General Electric Company
7 // Copyright 2018-2021 Collabora
9 #include <dt-bindings/input/input.h>
10 #include "imx6dl-qmx6.dtsi"
14 stdout-path = &uart3;
20 operating-points = <
25 fsl,soc-operating-points = <
26 /* ARM kHz SOC-PU uV */
33 operating-points = <
[all …]
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/qcom/ |
| D | msm8916-samsung-serranove.dts | 1 // SPDX-License-Identifier: GPL-2.0-only
6 /dts-v1/;
8 #include "msm8916-pm8916.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/interrupt-controller/irq.h>
22 * arch/arm/boot/dts/qcom-msm8916-samsung-serranove.dts
28 chassis-type = "handset";
37 stdout-path = "serial0";
40 reserved-memory {
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/iio/frequency/ |
| D | adf4350.txt | 4 - compatible: Should be one of
7 - reg: SPI chip select numbert for the device
8 - spi-max-frequency: Max SPI frequency to use (< 20000000)
9 - clocks: From common clock binding. Clock is phandle to clock for
13 - gpios: GPIO Lock detect - If set with a valid phandle and GPIO number,
15 - adi,channel-spacing: Channel spacing in Hz (influences MODULUS).
16 - adi,power-up-frequency: If set in Hz the PLL tunes to
18 - adi,reference-div-factor: If set the driver skips dynamic calculation
20 - adi,reference-doubler-enable: Enables reference doubler.
21 - adi,reference-div2-enable: Enables reference divider.
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/extcon/ |
| D | extcon-max3355.txt | 2 -------------------------------------
4 MAX3355 integrates a charge pump and comparators to enable a system with an
5 integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
9 - compatible: should be "maxim,max3355";
10 - maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin
12 - id-gpios: should contain a phandle and GPIO specifier for the GPIO pin
17 usb-otg {
19 maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
20 id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/extcon/ |
| D | extcon-max3355.txt | 2 -------------------------------------
4 MAX3355 integrates a charge pump and comparators to enable a system with an
5 integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
9 - compatible: should be "maxim,max3355";
10 - maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin
12 - id-gpios: should contain a phandle and GPIO specifier for the GPIO pin
17 usb-otg {
19 maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
20 id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/qcom/ |
| D | qcom-msm8974pro-sony-xperia-shinano-castor.dts | 1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974pro.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/leds/common.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
11 compatible = "sony,xperia-castor", "qcom,msm8974pro", "qcom,msm8974";
12 chassis-type = "tablet";
20 stdout-path = "serial0:115200n8";
23 gpio-keys {
24 compatible = "gpio-keys";
[all …]
|
| D | qcom-apq8026-huawei-sturgeon.dts | 1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include "qcom-msm8226.dtsi"
10 #include <dt-bindings/input/ti-drv260x.h>
12 /delete-node/ &adsp_region;
17 chassis-type = "watch";
18 qcom,msm-id = <199 0x20000>;
19 qcom,board-id = <8 4>;
21 reserved-memory {
24 no-map;
[all …]
|
| D | qcom-msm8974-sony-xperia-rhine.dtsi | 1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/leds/common.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
15 stdout-path = "serial0:115200n8";
18 gpio-keys {
19 compatible = "gpio-keys";
21 pinctrl-names = "default";
22 pinctrl-0 = <&gpio_keys_pin_a>;
[all …]
|
| D | qcom-msm8974pro-fairphone-fp2.dts | 1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974pro.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/leds/common.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
12 chassis-type = "handset";
21 stdout-path = "serial0:115200n8";
24 gpio-keys {
25 compatible = "gpio-keys";
27 pinctrl-names = "default";
[all …]
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | qcom-msm8974-sony-xperia-castor.dts | 1 #include "qcom-msm8974pro.dtsi"
2 #include "qcom-pm8841.dtsi"
3 #include "qcom-pm8941.dtsi"
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
10 compatible = "sony,xperia-castor", "qcom,msm8974";
17 stdout-path = "serial0:115200n8";
20 gpio-keys {
21 compatible = "gpio-keys";
[all …]
|
| D | qcom-msm8974-sony-xperia-honami.dts | 1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974.dtsi"
3 #include "qcom-pm8841.dtsi"
4 #include "qcom-pm8941.dtsi"
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
11 compatible = "sony,xperia-honami", "qcom,msm8974";
18 stdout-path = "serial0:115200n8";
21 gpio-keys {
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/iio/frequency/ |
| D | adi,adf4350.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Michael Hennerich <michael.hennerich@analog.com>
15 - adi,adf4350
16 - adi,adf4351
21 spi-max-frequency:
28 clock-names:
31 gpios:
35 adi,channel-spacing:
[all …]
|
1234567891011