Searched full:electrical (Results 1 – 25 of 142) sorted by relevance
123456
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/display/panel/ |
| D | tpo,tpg110.yaml | 27 If some electrical strap or alternate resolution is desired,
31 certain electrical driving levels.
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/display/panel/ |
| D | tpo,tpg110.yaml | 27 If some electrical strap or alternate resolution is desired,
31 certain electrical driving levels.
|
| /kernel/linux/linux-6.6/drivers/usb/chipidea/ |
| D | otg_fsm.h | 21 * Table 4-1: Electrical Characteristics
22 * ->DC Electrical Timing
|
| /kernel/linux/linux-5.10/drivers/usb/chipidea/ |
| D | otg_fsm.h | 21 * Table 4-1: Electrical Characteristics
22 * ->DC Electrical Timing
|
| /kernel/linux/linux-6.6/Documentation/driver-api/soundwire/ |
| D | error_handling.rst | 23 slots) or electrical issues during the transmit/receive transition cannot
35 Slave or to a non-implemented register) or electrical issue, no response
|
| /kernel/linux/linux-5.10/Documentation/driver-api/soundwire/ |
| D | error_handling.rst | 23 slots) or electrical issues during the transmit/receive transition cannot
35 Slave or to a non-implemented register) or electrical issue, no response
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/phy/ |
| D | mixel,mipi-dsi-phy.txt | 5 electrical signals for DSI.
|
| /kernel/linux/linux-6.6/drivers/thunderbolt/ |
| D | Kconfig | 36 under each USB4 port. Used for electrical quality and robustness
|
| /kernel/linux/linux-5.10/Documentation/driver-api/ |
| D | miscellaneous.rst | 29 control power supplied to electrical devices.
|
| D | i2c.rst | 30 systems are also I2C conformant. The electrical constraints are tighter
|
| D | pinctl.rst | 397 is a way for chip vendors producing some kind of electrical packages to use
747 that your datasheet calls "GPIO mode", but actually is just an electrical
802 software-control a few electrical properties of the pin that you would
821 Here some electrical properties of the pin can be configured no matter
869 - Registers (or fields within registers) that control electrical
890 Electrical properties of the pin such as biasing and drive strength
969 GPIO subsystem. It is just an electrical configuration used by that device
|
| /kernel/linux/linux-5.10/include/linux/mtd/ |
| D | jedec.h | 55 /* electrical parameter block */
|
| /kernel/linux/linux-6.6/Documentation/driver-api/ |
| D | miscellaneous.rst | 28 control power supplied to electrical devices.
|
| D | i2c.rst | 30 systems are also I2C conformant. The electrical constraints are tighter
|
| D | pin-control.rst | 397 is a way for chip vendors producing some kind of electrical packages to use
702 that your datasheet calls "GPIO mode", but actually is just an electrical
757 software-control a few electrical properties of the pin that you would
777 Here some electrical properties of the pin can be configured no matter
823 - Registers (or fields within registers) that control electrical
844 Electrical properties of the pin such as biasing and drive strength
926 GPIO subsystem. It is just an electrical configuration used by that device
|
| /kernel/linux/linux-6.6/include/linux/mtd/ |
| D | jedec.h | 58 /* electrical parameter block */
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/gpio/ |
| D | gpio-delay.yaml | 13 This binding describes an electrical setup where setting an GPIO output
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/intel/e1000e/ |
| D | 80003es2lan.h | 64 /* 1=Enable SERDES Electrical Idle */
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/intel/e1000e/ |
| D | 80003es2lan.h | 64 /* 1=Enable SERDES Electrical Idle */
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/phy/ |
| D | mixel,mipi-dsi-phy.yaml | 15 electrical signals for DSI.
|
| /kernel/linux/linux-5.10/Documentation/i2c/ |
| D | summary.rst | 27 meet both SMBus and I2C electrical constraints; and others which can't
|
| /kernel/linux/linux-6.6/Documentation/i2c/ |
| D | summary.rst | 29 meet both SMBus and I2C electrical constraints; and others which can't
|
| /kernel/linux/linux-6.6/drivers/net/can/ctucanfd/ |
| D | ctucanfd.h | 16 * Faculty of Electrical Engineering (http://www.fel.cvut.cz)
|
| D | ctucanfd_kframe.h | 16 * Faculty of Electrical Engineering (http://www.fel.cvut.cz)
|
| /kernel/linux/linux-5.10/Documentation/driver-api/gpio/ |
| D | driver.rst | 62 - method to set electrical configuration for a given GPIO line
91 GPIO electrical configuration
94 GPIO lines can be configured for several electrical modes of operation by using
250 supports more versatile control over electrical properties and can handle
|
123456