| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/sound/ |
| D | rt5668.txt | 7 - compatible : "realtek,rt5668b"
9 - reg : The I2C address of the device.
13 - interrupts : The CODEC's interrupt output.
15 - realtek,dmic1-data-pin
20 - realtek,dmic1-clk-pin
24 - realtek,jd-src
25 0: No JD is used
26 1: using JD1 as JD source
28 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
43 interrupt-parent = <&gpio>;
[all …]
|
| D | rt5682.txt | 7 - compatible : "realtek,rt5682" or "realtek,rt5682i"
9 - reg : The I2C address of the device.
13 - interrupts : The CODEC's interrupt output.
15 - realtek,dmic1-data-pin
20 - realtek,dmic1-clk-pin
24 - realtek,jd-src
25 0: No JD is used
26 1: using JD1 as JD source
28 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
30 - realtek,btndet-delay
[all …]
|
| D | rt5665.txt | 7 - compatible : One of "realtek,rt5665", "realtek,rt5666".
9 - reg : The I2C address of the device.
11 - interrupts : The CODEC's interrupt output.
15 - realtek,in1-differential
16 - realtek,in2-differential
17 - realtek,in3-differential
18 - realtek,in4-differential
19 Boolean. Indicate MIC1/2/3/4 input are differential, rather than single-ended.
21 - realtek,dmic1-data-pin
26 - realtek,dmic2-data-pin
[all …]
|
| D | rt5659.txt | 7 - compatible : One of "realtek,rt5659" or "realtek,rt5658".
9 - reg : The I2C address of the device.
11 - interrupts : The CODEC's interrupt output.
15 - clocks: The phandle of the master clock to the CODEC
16 - clock-names: Should be "mclk"
18 - realtek,in1-differential
19 - realtek,in3-differential
20 - realtek,in4-differential
21 Boolean. Indicate MIC1/3/4 input are differential, rather than single-ended.
23 - realtek,dmic1-data-pin
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/sound/ |
| D | rt5668.txt | 7 - compatible : "realtek,rt5668b"
9 - reg : The I2C address of the device.
13 - interrupts : The CODEC's interrupt output.
15 - realtek,dmic1-data-pin
20 - realtek,dmic1-clk-pin
24 - realtek,jd-src
25 0: No JD is used
26 1: using JD1 as JD source
28 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
43 interrupt-parent = <&gpio>;
[all …]
|
| D | realtek,rt5682s.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Derek Fang <derek.fang@realtek.com>
13 Rt5682s(ALC5682I-VS) is a rt5682i variant which supports I2C only.
16 - $ref: dai-common.yaml#
30 realtek,dmic1-data-pin:
33 - 0 # dmic1 data is not used
34 - 1 # using GPIO2 pin as dmic1 data pin
35 - 2 # using GPIO5 pin as dmic1 data pin
[all …]
|
| D | rt5682.txt | 7 - compatible : "realtek,rt5682" or "realtek,rt5682i"
9 - reg : The I2C address of the device.
11 - AVDD-supply: phandle to the regulator supplying analog power through the
14 - MICVDD-supply: phandle to the regulator supplying power for the microphone
17 - VBAT-supply: phandle to the regulator supplying battery power through the
20 - DBVDD-supply: phandle to the regulator supplying I/O power through the DBVDD
23 - LDO1-IN-supply: phandle to the regulator supplying power to the digital core
28 - interrupts : The CODEC's interrupt output.
30 - realtek,dmic1-data-pin
35 - realtek,dmic1-clk-pin
[all …]
|
| D | rt5659.txt | 7 - compatible : One of "realtek,rt5659" or "realtek,rt5658".
9 - reg : The I2C address of the device.
11 - interrupts : The CODEC's interrupt output.
15 - clocks: The phandle of the master clock to the CODEC
16 - clock-names: Should be "mclk"
18 - realtek,in1-differential
19 - realtek,in3-differential
20 - realtek,in4-differential
21 Boolean. Indicate MIC1/3/4 input are differential, rather than single-ended.
23 - realtek,dmic1-data-pin
[all …]
|
| D | rt5665.txt | 7 - compatible : One of "realtek,rt5665", "realtek,rt5666".
9 - reg : The I2C address of the device.
11 - interrupts : The CODEC's interrupt output.
15 - realtek,in1-differential
16 - realtek,in2-differential
17 - realtek,in3-differential
18 - realtek,in4-differential
19 Boolean. Indicate MIC1/2/3/4 input are differential, rather than single-ended.
21 - realtek,dmic1-data-pin
26 - realtek,dmic2-data-pin
[all …]
|
| /kernel/linux/linux-6.6/sound/soc/codecs/ |
| D | src4xxx.c | 1 // SPDX-License-Identifier: GPL-2.0
5 // Copyright 2021-2022 Deqx Pty Ltd
24 /* SRC attenuation */
25 static const DECLARE_TLV_DB_SCALE(src_tlv, -12750, 50, 0);
28 SOC_DOUBLE_R_TLV("SRC Volume",
34 "loopback", "other_port", "DIR", "SRC"
46 static const char * const dit_mux_text[] = {"Port A", "Port B", "DIR", "SRC"};
51 /* SRC control */
55 SOC_DAPM_ENUM("SRC source select", src_in_enum);
85 SND_SOC_DAPM_MUX("DIT Out Src", SRC4XXX_PWR_RST_01,
[all …]
|
| D | arizona-jack.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * extcon-arizona.c - Extcon driver Wolfson Arizona devices
5 * Copyright (C) 2012-2014 Wolfson Microelectronics plc
26 #include <dt-bindings/mfd/arizona.h>
33 * The hardware supports 8 ranges / buttons, but the snd-jack interface
34 * only supports 6 buttons (button 0-5).
100 struct arizona *arizona = info->arizona; in arizona_extcon_hp_clamp()
105 switch (arizona->type) { in arizona_extcon_hp_clamp()
122 ret = regmap_update_bits(arizona->regmap, in arizona_extcon_hp_clamp()
127 dev_warn(arizona->dev, "Failed to set TST_CAP_SEL: %d\n", ret); in arizona_extcon_hp_clamp()
[all …]
|
| D | rt712-sdca.c | 1 // SPDX-License-Identifier: GPL-2.0-only
3 // rt712-sdca.c -- rt712 SDCA ALSA SoC audio driver
23 #include <sound/soc-dapm.h>
25 #include "rt712-sdca.h"
31 struct regmap *regmap = rt712->mbq_regmap; in rt712_sdca_index_write()
36 dev_err(&rt712->slave->dev, in rt712_sdca_index_write()
47 struct regmap *regmap = rt712->mbq_regmap; in rt712_sdca_index_read()
52 dev_err(&rt712->slave->dev, in rt712_sdca_index_read()
77 struct regmap *regmap = rt712->regmap; in rt712_sdca_calibration()
81 mutex_lock(&rt712->calibrate_mutex); in rt712_sdca_calibration()
[all …]
|
| D | rt711-sdca.c | 1 // SPDX-License-Identifier: GPL-2.0-only
3 // rt711-sdca.c -- rt711 SDCA ALSA SoC audio driver
22 #include <sound/soc-dapm.h>
27 #include "rt711-sdca.h"
33 struct regmap *regmap = rt711->mbq_regmap; in rt711_sdca_index_write()
38 dev_err(&rt711->slave->dev, in rt711_sdca_index_write()
49 struct regmap *regmap = rt711->mbq_regmap; in rt711_sdca_index_read()
54 dev_err(&rt711->slave->dev, in rt711_sdca_index_read()
88 struct regmap *regmap = rt711->regmap; in rt711_sdca_calibration()
92 mutex_lock(&rt711->calibrate_mutex); in rt711_sdca_calibration()
[all …]
|
| D | rt711.c | 1 // SPDX-License-Identifier: GPL-2.0
3 // rt711.c -- rt711 ALSA SoC audio driver
24 #include <sound/soc-dapm.h>
89 struct regmap *regmap = rt711->regmap; in rt711_calibration()
92 mutex_lock(&rt711->calibrate_mutex); in rt711_calibration()
93 regmap_write(rt711->regmap, in rt711_calibration()
113 pr_err("%s, calibration time-out!\n", in rt711_calibration()
115 ret = -ETIMEDOUT; in rt711_calibration()
129 regmap_write(rt711->regmap, in rt711_calibration()
131 mutex_unlock(&rt711->calibrate_mutex); in rt711_calibration()
[all …]
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/mediatek/ |
| D | mt8192-asurada-audio-rt5682.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
7 rt5682: audio-codec@1a {
10 interrupts-extended = <&pio 18 IRQ_TYPE_LEVEL_LOW>;
11 realtek,jd-src = <1>;
12 realtek,btndet-delay = <16>;
13 #sound-dai-cells = <1>;
15 AVDD-supply = <&mt6359_vio18_ldo_reg>;
16 DBVDD-supply = <&mt6359_vio18_ldo_reg>;
17 LDO1-IN-supply = <&mt6359_vio18_ldo_reg>;
18 MICVDD-supply = <&pp3300_g>;
[all …]
|
| /kernel/linux/linux-5.10/drivers/media/dvb-frontends/ |
| D | zl10039.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Driver for Zarlink ZL10039 DVB-S tuner
5 * Copyright 2007 Jan D. Louw <jd.louw@mweb.co.za>
64 .addr = state->i2c_addr, in zl10039_read()
69 .addr = state->i2c_addr, in zl10039_read()
78 if (i2c_transfer(state->i2c, msg, 2) != 2) { in zl10039_read()
80 return -EREMOTEIO; in zl10039_read()
87 const enum zl10039_reg_addr reg, const u8 *src, in zl10039_write() argument
92 .addr = state->i2c_addr, in zl10039_write()
102 return -EINVAL; in zl10039_write()
[all …]
|
| /kernel/linux/linux-6.6/drivers/media/dvb-frontends/ |
| D | zl10039.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Driver for Zarlink ZL10039 DVB-S tuner
5 * Copyright 2007 Jan D. Louw <jd.louw@mweb.co.za>
64 .addr = state->i2c_addr, in zl10039_read()
69 .addr = state->i2c_addr, in zl10039_read()
78 if (i2c_transfer(state->i2c, msg, 2) != 2) { in zl10039_read()
80 return -EREMOTEIO; in zl10039_read()
87 const enum zl10039_reg_addr reg, const u8 *src, in zl10039_write() argument
92 .addr = state->i2c_addr, in zl10039_write()
102 return -EINVAL; in zl10039_write()
[all …]
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/qcom/ |
| D | sc7280-herobrine-audio-rt5682.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
11 /* BOARD-SPECIFIC TOP LEVEL NODES */
13 compatible = "google,sc7280-herobrine";
14 model = "sc7280-rt5682-max98360a-1mic";
16 audio-routing = "Headphone Jack", "HPOL",
19 #address-cells = <1>;
20 #size-cells = <0>;
22 dai-link@0 {
23 link-name = "MAX98360";
27 sound-dai = <&lpass_cpu MI2S_SECONDARY>;
[all …]
|
| D | sc7280-herobrine-audio-rt5682-3mic.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
11 /* BOARD-SPECIFIC TOP LEVEL NODES */
13 compatible = "google,sc7280-herobrine";
14 model = "sc7280-rt5682-max98360a-3mic";
16 audio-routing = "VA DMIC0", "vdd-micb",
17 "VA DMIC1", "vdd-micb",
18 "VA DMIC2", "vdd-micb",
19 "VA DMIC3", "vdd-micb",
24 #address-cells = <1>;
25 #size-cells = <0>;
[all …]
|
| /kernel/linux/linux-5.10/sound/soc/intel/boards/ |
| D | sof_sdw_rt711_sdca.c | 1 // SPDX-License-Identifier: GPL-2.0-only
5 * sof_sdw_rt711_sdca - Helpers to handle RT711-SDCA from generic machine driver
15 #include <sound/soc-acpi.h>
16 #include <sound/soc-dapm.h>
32 return -EPROBE_DEFER; in rt711_sdca_add_codec_device_props()
35 props[0] = PROPERTY_ENTRY_U32("realtek,jd-src", in rt711_sdca_add_codec_device_props()
74 struct snd_soc_card *card = rtd->card; in rt711_sdca_rtd_init()
77 struct snd_soc_component *component = codec_dai->component; in rt711_sdca_rtd_init()
81 card->components = devm_kasprintf(card->dev, GFP_KERNEL, in rt711_sdca_rtd_init()
82 "%s hs:rt711-sdca", in rt711_sdca_rtd_init()
[all …]
|
| D | sof_sdw_rt711.c | 1 // SPDX-License-Identifier: GPL-2.0-only
5 * sof_sdw_rt711 - Helpers to handle RT711 from generic machine driver
15 #include <sound/soc-acpi.h>
16 #include <sound/soc-dapm.h>
32 return -EPROBE_DEFER; in rt711_add_codec_device_props()
35 props[0] = PROPERTY_ENTRY_U32("realtek,jd-src", in rt711_add_codec_device_props()
74 struct snd_soc_card *card = rtd->card; in rt711_rtd_init()
77 struct snd_soc_component *component = codec_dai->component; in rt711_rtd_init()
81 card->components = devm_kasprintf(card->dev, GFP_KERNEL, in rt711_rtd_init()
83 card->components); in rt711_rtd_init()
[all …]
|
| /kernel/linux/linux-6.6/sound/soc/intel/boards/ |
| D | sof_sdw_rt711.c | 1 // SPDX-License-Identifier: GPL-2.0-only
5 * sof_sdw_rt711 - Helpers to handle RT711 from generic machine driver
15 #include <sound/soc-acpi.h>
16 #include <sound/soc-dapm.h>
32 props[0] = PROPERTY_ENTRY_U32("realtek,jd-src", SOF_JACK_JDSRC(sof_sdw_quirk)); in rt711_add_codec_device_props()
74 struct snd_soc_card *card = rtd->card; in rt711_rtd_init()
77 struct snd_soc_component *component = codec_dai->component; in rt711_rtd_init()
81 card->components = devm_kasprintf(card->dev, GFP_KERNEL, in rt711_rtd_init()
83 card->components); in rt711_rtd_init()
84 if (!card->components) in rt711_rtd_init()
[all …]
|
| D | sof_sdw_rt_sdca_jack_common.c | 1 // SPDX-License-Identifier: GPL-2.0-only
5 * sof_sdw_rt711_sdca - Helpers to handle RT711-SDCA from generic machine driver
15 #include <sound/soc-acpi.h>
16 #include <sound/soc-dapm.h>
33 props[0] = PROPERTY_ENTRY_U32("realtek,jd-src", SOF_JACK_JDSRC(sof_sdw_quirk)); in rt_sdca_jack_add_codec_device_props()
84 struct snd_soc_card *card = rtd->card; in rt_sdca_jack_rtd_init()
87 struct snd_soc_component *component = codec_dai->component; in rt_sdca_jack_rtd_init()
91 card->components = devm_kasprintf(card->dev, GFP_KERNEL, in rt_sdca_jack_rtd_init()
92 "%s hs:%s-sdca", in rt_sdca_jack_rtd_init()
93 card->components, component->name_prefix); in rt_sdca_jack_rtd_init()
[all …]
|
| /kernel/linux/linux-5.10/drivers/extcon/ |
| D | extcon-arizona.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * extcon-arizona.c - Extcon driver Wolfson Arizona devices
5 * Copyright (C) 2012-2014 Wolfson Microelectronics plc
21 #include <linux/extcon-provider.h>
28 #include <dt-bindings/mfd/arizona.h>
143 struct arizona *arizona = info->arizona; in arizona_extcon_hp_clamp()
148 switch (arizona->type) { in arizona_extcon_hp_clamp()
165 ret = regmap_update_bits(arizona->regmap, in arizona_extcon_hp_clamp()
170 dev_warn(arizona->dev, in arizona_extcon_hp_clamp()
180 snd_soc_dapm_mutex_lock(arizona->dapm); in arizona_extcon_hp_clamp()
[all …]
|
| /kernel/linux/linux-5.10/Documentation/dev-tools/ |
| D | kselftest.rst | 15 On some systems, hot-plug tests could hang forever waiting for cpu and
16 memory to be ready to be offlined. A special hot-plug target is created
17 to run the full range of hot-plug tests. In default mode, hot-plug tests run
18 in safe mode with a limited scope. In limited mode, cpu-hotplug test is
31 $ make -C tools/testing/selftests
35 $ make -C tools/testing/selftests run_tests
46 kernel src. This is applicable to "Running a subset of selftests" section
78 $ make -C tools/testing/selftests TARGETS=ptrace run_tests
97 $ make -C tools/testing/selftests SKIP_TARGETS=ptrace run_tests
108 See the top-level tools/testing/selftests/Makefile for the list of all
[all …]
|