Home
last modified time | relevance | path

Searched +full:mdio +full:- +full:mux +full:- +full:2 (Results 1 – 25 of 326) sorted by relevance

12345678910>>...14

/kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/
Dmdio-mux-multiplexer.txt1 Properties for an MDIO bus multiplexer consumer device
3 This is a special case of MDIO mux when MDIO mux is defined as a consumer
4 of a mux producer device. The mux producer can be of any type like mmio mux
5 producer, gpio mux producer or generic register based mux producer.
7 Required properties in addition to the MDIO Bus multiplexer properties:
9 - compatible : should be "mmio-mux-multiplexer"
10 - mux-controls : mux controller node to use for operating the mux
11 - mdio-parent-bus : phandle to the parent MDIO bus.
13 each child node of mdio bus multiplexer consumer device represent a mdio
17 Documentation/devicetree/bindings/mux/mux-controller.txt
[all …]
Dmdio-mux-mmioreg.txt1 Properties for an MDIO bus multiplexer controlled by a memory-mapped device
3 This is a special case of a MDIO bus multiplexer. A memory-mapped device,
4 like an FPGA, is used to control which child bus is connected. The mdio-mux
5 node must be a child of the memory-mapped device. The driver currently only
6 supports devices with 8, 16 or 32-bit registers.
10 - compatible : string, must contain "mdio-mux-mmioreg"
12 - reg : integer, contains the offset of the register that controls the bus
14 register, and must therefore be 1, 2, or 4.
16 - mux-mask : integer, contains an eight-bit mask that specifies which
18 'reg' property of each child mdio-mux node must be constrained by
[all …]
Dallwinner,sun8i-a83t-emac.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/allwinner,sun8i-a83t-emac.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Chen-Yu Tsai <wens@csie.org>
11 - Maxime Ripard <mripard@kernel.org>
16 - const: allwinner,sun8i-a83t-emac
17 - const: allwinner,sun8i-h3-emac
18 - const: allwinner,sun8i-r40-emac
19 - const: allwinner,sun8i-v3s-emac
[all …]
Dmdio-mux-gpio.txt1 Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
3 This is a special case of a MDIO bus multiplexer. One or more GPIO
8 - compatible : mdio-mux-gpio.
9 - gpios : GPIO specifiers for each GPIO line. One or more must be specified.
14 /* The parent MDIO bus. */
15 smi1: mdio@1180000001900 {
16 compatible = "cavium,octeon-3860-mdio";
17 #address-cells = <1>;
18 #size-cells = <0>;
23 An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/net/
Dmdio-mux-multiplexer.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-multiplexer.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Properties for an MDIO bus multiplexer consumer device
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of MDIO mux when MDIO mux is defined as a consumer
14 of a mux producer device. The mux producer can be of any type like mmio mux
15 producer, gpio mux producer or generic register based mux producer.
19 - $ref: /schemas/net/mdio-mux.yaml#
[all …]
Dmdio-mux-mmioreg.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-mmioreg.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Properties for an MDIO bus multiplexer controlled by a memory-mapped device
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of a MDIO bus multiplexer. A memory-mapped device,
14 like an FPGA, is used to control which child bus is connected. The mdio-mux
15 node must be a child of the memory-mapped device. The driver currently only
16 supports devices with 8, 16 or 32-bit registers.
[all …]
Dallwinner,sun8i-a83t-emac.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/allwinner,sun8i-a83t-emac.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Chen-Yu Tsai <wens@csie.org>
11 - Maxime Ripard <mripard@kernel.org>
16 - const: allwinner,sun8i-a83t-emac
17 - const: allwinner,sun8i-h3-emac
18 - const: allwinner,sun8i-r40-gmac
19 - const: allwinner,sun8i-v3s-emac
[all …]
Dbrcm,mdio-mux-iproc.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/net/brcm,mdio-mux-iproc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: MDIO bus multiplexer found in Broadcom iProc based SoCs.
10 - Florian Fainelli <f.fainelli@gmail.com>
13 This MDIO bus multiplexer defines buses that could be internal as well as
14 external to SoCs and could accept MDIO transaction compatible to C-22 or
15 C-45 Clause. When child bus is selected, one needs to select these two
16 properties as well to generate desired MDIO transaction on appropriate bus.
[all …]
Damlogic,gxl-mdio-mux.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/net/amlogic,gxl-mdio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Amlogic GXL MDIO bus multiplexer
10 - Jerome Brunet <jbrunet@baylibre.com>
13 This is a special case of a MDIO bus multiplexer. It allows to choose between
14 the internal mdio bus leading to the embedded 10/100 PHY or the external
15 MDIO bus on the Amlogic GXL SoC family.
18 - $ref: mdio-mux.yaml#
[all …]
Dbrcm,bcm6368-mdio-mux.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/net/brcm,bcm6368-mdio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Broadcom BCM6368 MDIO bus multiplexer
10 - Álvaro Fernández Rojas <noltari@gmail.com>
13 This MDIO bus multiplexer defines buses that could be internal as well as
15 properties as well to generate desired MDIO transaction on appropriate bus.
18 - $ref: mdio-mux.yaml#
22 const: brcm,bcm6368-mdio-mux
[all …]
Dmdio-mux-gpio.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-gpio.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of a MDIO bus multiplexer. One or more GPIO
17 - $ref: /schemas/net/mdio-mux.yaml#
21 const: mdio-mux-gpio
30 - compatible
[all …]
Damlogic,g12a-mdio-mux.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/net/amlogic,g12a-mdio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: MDIO bus multiplexer/glue of Amlogic G12a SoC family
10 This is a special case of a MDIO bus multiplexer. It allows to choose between
11 the internal mdio bus leading to the embedded 10/100 PHY or the external
12 MDIO bus.
15 - Neil Armstrong <neil.armstrong@linaro.org>
18 - $ref: mdio-mux.yaml#
[all …]
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/mux/
Dreg-mux.txt1 Generic register bitfield-based multiplexer controller bindings
7 - compatible : should be one of
8 "reg-mux" : if parent device of mux controller is not syscon device
9 "mmio-mux" : if parent device of mux controller is syscon device
10 - #mux-control-cells : <1>
11 - mux-reg-masks : an array of register offset and pre-shifted bitfield mask
12 pairs, each describing a single mux control.
13 * Standard mux-controller bindings as decribed in mux-controller.txt
16 - idle-states : if present, the state the muxes will have when idle. The
21 pair in the mux-reg-masks array.
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/mux/
Dreg-mux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/mux/reg-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Generic register bitfield-based multiplexer controller
10 - Peter Rosin <peda@axentia.se>
19 - reg-mux # parent device of mux controller is not syscon device
20 - mmio-mux # parent device of mux controller is syscon device
24 '#mux-control-cells':
27 mux-reg-masks:
[all …]
/kernel/linux/linux-6.6/arch/arm64/boot/dts/freescale/
Dfsl-lx2160a-qds.dts1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
7 /dts-v1/;
9 #include "fsl-lx2160a.dtsi"
13 compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
23 stdout-path = "serial0:115200n8";
26 sb_3v3: regulator-sb3v3 {
27 compatible = "regulator-fixed";
28 regulator-name = "MC34717-3.3VSB";
29 regulator-min-microvolt = <3300000>;
30 regulator-max-microvolt = <3300000>;
[all …]
Dfsl-lx2162a-qds.dts1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
7 /dts-v1/;
9 #include "fsl-lx2160a.dtsi"
13 compatible = "fsl,lx2162a-qds", "fsl,lx2160a";
23 stdout-path = "serial0:115200n8";
26 sb_3v3: regulator-sb3v3 {
27 compatible = "regulator-fixed";
28 regulator-name = "LTM4619-3.3VSB";
29 regulator-min-microvolt = <3300000>;
30 regulator-max-microvolt = <3300000>;
[all …]
Dfsl-ls208xa-qds.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
14 phy-handle = <&mdio0_phy12>;
15 phy-connection-type = "sgmii";
19 phy-handle = <&mdio0_phy13>;
20 phy-connection-type = "sgmii";
24 phy-handle = <&mdio0_phy14>;
25 phy-connection-type = "sgmii";
29 phy-handle = <&mdio0_phy15>;
30 phy-connection-type = "sgmii";
34 mmc-hs200-1_8v;
[all …]
Dfsl-ls1028a-qds.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
11 /dts-v1/;
13 #include "fsl-ls1028a.dtsi"
17 compatible = "fsl,ls1028a-qds", "fsl,ls1028a";
32 stdout-path = "serial0:115200n8";
40 sys_mclk: clock-mclk {
41 compatible = "fixed-clock";
42 #clock-cells = <0>;
43 clock-frequency = <25000000>;
46 reg_1p8v: regulator-1p8v {
[all …]
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/pinctrl/
Dlantiq,pinctrl-xway.txt4 - compatible: "lantiq,pinctrl-xway", (DEPRECATED: Use "lantiq,pinctrl-danube")
5 "lantiq,pinctrl-xr9", (DEPRECATED: Use "lantiq,xrx100-pinctrl" or
6 "lantiq,xrx200-pinctrl")
7 "lantiq,pinctrl-ase", (DEPRECATED: Use "lantiq,ase-pinctrl")
8 "lantiq,<chip>-pinctrl", where <chip> is:
14 - reg: Should contain the physical address and length of the gpio/pinmux
17 Please refer to pinctrl-bindings.txt in this directory for details of the
24 mux function to select on those group(s), and two pin configuration parameters:
25 pull-up and open-drain
31 other words, a subnode that lists a mux function but no pin configuration
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/pinctrl/
Dlantiq,pinctrl-xway.txt4 - compatible: "lantiq,<chip>-pinctrl", where <chip> is:
10 - reg: Should contain the physical address and length of the gpio/pinmux
13 Please refer to pinctrl-bindings.txt in this directory for details of the
20 mux function to select on those group(s), and two pin configuration parameters:
21 pull-up and open-drain
27 other words, a subnode that lists a mux function but no pin configuration
30 information about e.g. the mux function.
32 We support 2 types of nodes.
34 Definition of mux function groups:
36 Required subnode-properties:
[all …]
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/soc/ti/
Dti,pruss.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 TI Programmable Real-Time Unit and Industrial Communication Subsystem
11 - Suman Anna <s-anna@ti.com>
15 The Programmable Real-Time Unit and Industrial Communication Subsystem
16 (PRU-ICSS a.k.a. PRUSS) is present on various TI SoCs such as AM335x, AM437x,
17 Keystone 66AK2G, OMAP-L138/DA850 etc. A PRUSS consists of dual 32-bit RISC
18 cores (Programmable Real-Time Units, or PRUs), shared RAM, data and
23 peripheral interfaces, fast real-time responses, or specialized data handling.
[all …]
/kernel/linux/linux-5.10/arch/powerpc/boot/dts/fsl/
Dp5040ds.dts4 * Copyright 2012 - 2015 Freescale Semiconductor Inc.
20 * Foundation, either version 2 of that License or (at your option) any
35 /include/ "p5040si-pre.dtsi"
40 #address-cells = <2>;
41 #size-cells = <2>;
42 interrupt-parent = <&mpic>;
74 reserved-memory {
75 #address-cells = <2>;
76 #size-cells = <2>;
79 bman_fbpr: bman-fbpr {
[all …]
/kernel/linux/linux-6.6/arch/powerpc/boot/dts/fsl/
Dp5040ds.dts4 * Copyright 2012 - 2015 Freescale Semiconductor Inc.
20 * Foundation, either version 2 of that License or (at your option) any
35 /include/ "p5040si-pre.dtsi"
40 #address-cells = <2>;
41 #size-cells = <2>;
42 interrupt-parent = <&mpic>;
74 reserved-memory {
75 #address-cells = <2>;
76 #size-cells = <2>;
79 bman_fbpr: bman-fbpr {
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/soc/ti/
Dti,pruss.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 TI Programmable Real-Time Unit and Industrial Communication Subsystem
11 - Suman Anna <s-anna@ti.com>
15 The Programmable Real-Time Unit and Industrial Communication Subsystem
16 (PRU-ICSS a.k.a. PRUSS) is present on various TI SoCs such as AM335x, AM437x,
17 Keystone 66AK2G, OMAP-L138/DA850 etc. A PRUSS consists of dual 32-bit RISC
18 cores (Programmable Real-Time Units, or PRUs), shared RAM, data and
23 peripheral interfaces, fast real-time responses, or specialized data handling.
[all …]
/kernel/linux/linux-5.10/arch/arm/boot/dts/
Dqcom-ipq8064-rb3011.dts1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-ipq8064.dtsi"
3 #include <dt-bindings/input/input.h>
6 model = "MikroTik RB3011UiAS-RM";
13 mdio-gpio0 = &mdio0;
14 mdio-gpio1 = &mdio1;
19 stdout-path = "serial0:115200n8";
27 mdio0: mdio-0 {
29 compatible = "virtual,mdio-gpio";
32 #address-cells = <1>;
[all …]

12345678910>>...14