| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/sound/ |
| D | everest,es8326.yaml | 65 Bit(2) 1 means button press triggers irq, 0 means not.
66 Bit(3) 1 means PIN9 is the irq source for jack detection. When set to 0,
68 Bit(4) 1 means PIN27 is the irq source for jack detection.
69 Bit(5) 1 means PIN9 is the irq source after MIC detect.
70 Bit(6) 1 means PIN27 is the irq source after MIC detect.
79 Bit(0-3) 0 means irq pulse equals 512*internal clock
80 1 means irq pulse equals 1024*internal clock
81 2 means ...
82 7 means irq pulse equals 65536*internal clock
83 8 means irq mutes PA
[all …]
|
| /kernel/linux/linux-6.6/Documentation/ABI/testing/ |
| D | sysfs-platform-asus-laptop | 16 - 0 (0000b) means no display
24 Control the gps device. 1 means on, 0 means off.
46 Control the bluetooth device. 1 means on, 0 means off.
55 Control the wlan device. 1 means on, 0 means off.
64 Control the wimax device. 1 means on, 0 means off.
71 Control the wwan (3G) device. 1 means on, 0 means off.
|
| D | sysfs-class-devlink | 25 'consumer unbind' means the device link will be removed when
28 'supplier unbind' means the device link will be removed when
31 'never' means the device link will not be automatically removed
81 'not tracked' means this device link does not track the status
85 'dormant' means the supplier and the consumer devices have not
88 'available' means the supplier has bound to its driver and is
91 'consumer probing' means the consumer device is currently
94 'active' means the supplier and consumer devices have both
97 'supplier unbinding' means the supplier devices is currently in
100 'unknown' means the state of the device link is not any of the
[all …]
|
| D | sysfs-platform-lg-laptop | 6 Control reader mode. 1 means on, 0 means off.
13 Control FN lock mode. 1 means on, 0 means off.
36 1 means on, 0 means off.
|
| D | sysfs-driver-samsung-laptop | 31 - 0 means normal battery mode (100% charge)
32 - 1 means battery life extender mode (80% charge)
40 1 means enabled, 0 means disabled.
48 1 means enabled, 0 means disabled.
|
| D | sysfs-class-remoteproc | 25 "offline" means the remote processor is powered off.
27 "suspended" means that the remote processor is suspended and
74 "disabled" means no dump will be collected.
76 "enabled" means when the remote processor's coredump is
80 "inline" means when the remote processor's coredump is
97 "enabled" means, the remote processor will be automatically
102 "disabled" means, a remote processor will remain in a crashed
|
| D | sysfs-platform-eeepc-laptop | 19 Control the camera. 1 means on, 0 means off.
26 Control the card reader. 1 means on, 0 means off.
49 For example, 0x301 means: mode 1 selected, 3 available modes.
|
| D | sysfs-platform-asus-wmi | 18 Control the camera. 1 means on, 0 means off.
25 Control the card reader. 1 means on, 0 means off.
32 Control the card touchpad. 1 means on, 0 means off.
39 Resume on lid open. 1 means on, 0 means off.
|
| /kernel/linux/linux-5.10/Documentation/ABI/testing/ |
| D | sysfs-platform-asus-laptop | 16 - 0 (0000b) means no display
24 Control the gps device. 1 means on, 0 means off.
46 Control the bluetooth device. 1 means on, 0 means off.
55 Control the wlan device. 1 means on, 0 means off.
64 Control the wimax device. 1 means on, 0 means off.
71 Control the wwan (3G) device. 1 means on, 0 means off.
|
| D | sysfs-class-devlink | 25 'consumer unbind' means the device link will be removed when
28 'supplier unbind' means the device link will be removed when
31 'never' means the device link will not be automatically removed
81 'not tracked' means this device link does not track the status
85 'dormant' means the supplier and the consumer devices have not
88 'available' means the supplier has bound to its driver and is
91 'consumer probing' means the consumer device is currently
94 'active' means the supplier and consumer devices have both
97 'supplier unbinding' means the supplier devices is currently in
100 'unknown' means the state of the device link is not any of the
[all …]
|
| D | sysfs-platform-asus-wmi | 18 Control the camera. 1 means on, 0 means off.
25 Control the card reader. 1 means on, 0 means off.
32 Control the card touchpad. 1 means on, 0 means off.
39 Resume on lid open. 1 means on, 0 means off.
|
| D | sysfs-platform-lg-laptop | 6 Control reader mode. 1 means on, 0 means off.
13 Control FN lock mode. 1 means on, 0 means off.
35 1 means on, 0 means off.
|
| D | sysfs-driver-samsung-laptop | 31 - 0 means normal battery mode (100% charge)
32 - 1 means battery life extender mode (80% charge)
40 1 means enabled, 0 means disabled.
48 1 means enabled, 0 means disabled.
|
| D | sysfs-class-remoteproc | 25 "offline" means the remote processor is powered off.
27 "suspended" means that the remote processor is suspended and
74 "disabled" means no dump will be collected.
76 "enabled" means when the remote processor's coredump is
80 "inline" means when the remote processor's coredump is
97 "enabled" means, the remote processor will be automatically
102 "disabled" means, a remote processor will remain in a crashed
|
| D | sysfs-platform-eeepc-laptop | 19 Control the camera. 1 means on, 0 means off.
26 Control the card reader. 1 means on, 0 means off.
49 For example, 0x301 means: mode 1 selected, 3 available modes.
|
| D | sysfs-class-regulator | 16 'enabled' means the regulator output is ON and is supplying
19 'disabled' means the regulator output is OFF and is not
23 'unknown' means software cannot determine the state, or
46 "off" means the regulator is not supplying power to the
49 "on" means the regulator is supplying power to the system,
81 'voltage' means the regulator output voltage can be controlled
84 'current' means the regulator output current limit can be
87 'unknown' means software cannot control either voltage or
367 'enabled' means the regulator is in bypass mode.
369 'disabled' means that the regulator is regulating.
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/mtd/ |
| D | fsmc-nand.txt | 16 are valid. Zero means one clockcycle, 15 means 16 clock
21 Only valid for write transactions. Zero means zero cycles,
22 255 means 255 cycles.
24 when writing) after the command deassertation. Zero means
25 one cycle, 255 means 256 cycles.
27 NAND flash in response to SMWAITn. Zero means 1 cycle,
28 255 means 256 cycles.
30 command is asserted. Zero means one cycle, 255 means 256
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/mtd/ |
| D | fsmc-nand.txt | 16 are valid. Zero means one clockcycle, 15 means 16 clock
21 Only valid for write transactions. Zero means zero cycles,
22 255 means 255 cycles.
24 when writing) after the command deassertation. Zero means
25 one cycle, 255 means 256 cycles.
27 NAND flash in response to SMWAITn. Zero means 1 cycle,
28 255 means 256 cycles.
30 command is asserted. Zero means one cycle, 255 means 256
|
| /kernel/linux/linux-6.6/LICENSES/dual/ |
| D | copyleft-next-0.3.1 | 41 pertinent). "Legal Notices" means copyright notices, license notices,
49 licensing. This condition may not be avoided through such means as
75 means of providing network access to source code.
170 "Copyleft-Next Project" means the project that maintains the source
174 "Corresponding Source" of a Covered Work in Object Code form means (i)
184 "Covered Work" means My Work or a Derived Work.
186 "Derived Work" means a work of authorship that copies from, modifies,
194 "Distribute" means to distribute, transfer or make a copy available to
197 "Distributor" means Me and anyone else who Distributes a Covered Work.
199 "FSF-Free" means classified as 'free' by the Free Software Foundation.
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/pinctrl/ |
| D | mediatek,mt8365-pinctrl.yaml | 83 100: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
84 101: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
85 102: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
86 103: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
97 100: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
98 101: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
99 102: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
100 103: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
155 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
156 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
[all …]
|
| /kernel/linux/linux-5.10/arch/sh/include/mach-landisk/mach/ |
| D | gio.h | 18 * S means "Set" through a ptr,
19 * T means "Tell" directly
20 * G means "Get" (to a pointed var)
21 * Q means "Query", response is on the return value
22 * X means "eXchange": G and S atomically
23 * H means "sHift": T and Q atomically
|
| /kernel/linux/linux-6.6/arch/sh/include/mach-landisk/mach/ |
| D | gio.h | 18 * S means "Set" through a ptr,
19 * T means "Tell" directly
20 * G means "Get" (to a pointed var)
21 * Q means "Query", response is on the return value
22 * X means "eXchange": G and S atomically
23 * H means "sHift": T and Q atomically
|
| /kernel/linux/linux-6.6/Documentation/admin-guide/perf/ |
| D | hisi-pcie-pmu.rst | 79 For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0.
92 For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0"
93 means statistics start when TLP length > trigger condition, "trig_mode=1"
94 means start when TLP length < condition.
106 For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means
107 counter counts when TLP length >= threshold, and "thr_mode=1" means counts
124 For example, "len_mode=2" means only counting the bandwidth of TLP headers
125 and "len_mode=3" means the final bandwidth data is composed of both TLP
|
| /kernel/linux/linux-5.10/include/linux/ |
| D | pstore_blk.h | 18 * mean error. -ENOMSG means to try next zone.
58 * linux/pstore.h. It means what front-ends this device support.
59 * Zero means all backends for compatible.
64 * means error.
66 * -EBUSY means try to write again later.
67 * -ENOMSG means to try next zone.
76 * excluding -ENOMSG mean error. -ENOMSG means to try next zone.
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | mediatek,mt6779-pinctrl.yaml | 115 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
116 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
117 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
118 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
126 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
127 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
128 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
129 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
|