| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/cpu/ |
| D | idle-states.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/cpu/idle-states.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
11 - Anup Patel <anup@brainfault.org>
15 1 - Introduction
18 ARM and RISC-V systems contain HW capable of managing power consumption
19 dynamically, where cores can be put in different low-power states (ranging
22 run-time, can be specified through device tree bindings representing the
[all …]
|
| D | cpu-capacity.txt | 6 1 - Introduction
15 2 - CPU capacity definition
19 heterogeneity. Such heterogeneity can come from micro-architectural differences
23 capture a first-order approximation of the relative performance of CPUs.
29 * A "single-threaded" or CPU affine benchmark
43 3 - capacity-dmips-mhz
46 capacity-dmips-mhz is an optional cpu node [1] property: u32 value
51 capacity-dmips-mhz property is all-or-nothing: if it is specified for a cpu
54 available, final capacities are calculated by directly using capacity-dmips-
58 4 - Examples
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/arm/ |
| D | idle-states.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/arm/idle-states.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
14 1 - Introduction
18 where cores can be put in different low-power states (ranging from simple wfi
20 range of dynamic idle states that a processor can enter at run-time, can be
27 - Running
28 - Idle_standby
[all …]
|
| D | psci.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
15 processors") can be used by Linux to initiate various CPU-centric power
25 r0 => 32-bit Function ID / return value
26 {r1 - r3} => Parameters
40 - description:
44 - description:
46 const: arm,psci-0.2
[all …]
|
| D | cpu-capacity.txt | 6 1 - Introduction
15 2 - CPU capacity definition
19 heterogeneity. Such heterogeneity can come from micro-architectural differences
23 capture a first-order approximation of the relative performance of CPUs.
29 * A "single-threaded" or CPU affine benchmark
43 3 - capacity-dmips-mhz
46 capacity-dmips-mhz is an optional cpu node [1] property: u32 value
51 capacity-dmips-mhz property is all-or-nothing: if it is specified for a cpu
54 available, final capacities are calculated by directly using capacity-dmips-
58 4 - Examples
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/power/ |
| D | domain-idle-state.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/power/domain-idle-state.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Ulf Hansson <ulf.hansson@linaro.org>
18 const: domain-idle-states
21 "^(cpu|cluster|domain)-":
28 const: domain-idle-state
30 entry-latency-us:
33 state. Note that, the exit-latency-us duration may be guaranteed only
[all …]
|
| D | power-domain.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/power/power-domain.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Rafael J. Wysocki <rjw@rjwysocki.net>
11 - Kevin Hilman <khilman@kernel.org>
12 - Ulf Hansson <ulf.hansson@linaro.org>
24 \#power-domain-cells property in the PM domain provider node.
28 pattern: "^(power-controller|power-domain)([@-].*)?$"
30 domain-idle-states:
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/power/ |
| D | domain-idle-state.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/power/domain-idle-state.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Ulf Hansson <ulf.hansson@linaro.org>
18 const: domain-idle-states
21 "^(cpu|cluster|domain)-":
29 const: domain-idle-state
31 entry-latency-us:
34 state. Note that, the exit-latency-us duration may be guaranteed only
[all …]
|
| D | power-domain.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/power/power-domain.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Rafael J. Wysocki <rjw@rjwysocki.net>
11 - Kevin Hilman <khilman@kernel.org>
12 - Ulf Hansson <ulf.hansson@linaro.org>
24 \#power-domain-cells property in the PM domain provider node.
28 pattern: "^(power-controller|power-domain)([@-].*)?$"
30 domain-idle-states:
[all …]
|
| /kernel/linux/linux-5.10/arch/arm64/boot/dts/qcom/ |
| D | sdm630.dtsi | 1 // SPDX-License-Identifier: BSD-3-Clause
6 #include <dt-bindings/clock/qcom,gcc-sdm660.h>
7 #include <dt-bindings/clock/qcom,rpmcc.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 interrupt-parent = <&intc>;
14 #address-cells = <2>;
15 #size-cells = <2>;
20 xo_board: xo-board {
21 compatible = "fixed-clock";
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/arm/ |
| D | psci.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
15 processors") can be used by Linux to initiate various CPU-centric power
25 r0 => 32-bit Function ID / return value
26 {r1 - r3} => Parameters
40 - description:
44 - description:
52 - const: arm,psci-0.2
[all …]
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/qcom/ |
| D | sm4450.dtsi | 1 // SPDX-License-Identifier: BSD-3-Clause
6 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/interrupt-controller/arm-gic.h>
10 interrupt-parent = <&intc>;
12 #address-cells = <2>;
13 #size-cells = <2>;
18 xo_board: xo-board {
19 compatible = "fixed-clock";
20 clock-frequency = <76800000>;
21 #clock-cells = <0>;
[all …]
|
| D | sdx75.dtsi | 1 // SPDX-License-Identifier: BSD-3-Clause
9 #include <dt-bindings/clock/qcom,rpmh.h>
10 #include <dt-bindings/clock/qcom,sdx75-gcc.h>
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include <dt-bindings/power/qcom,rpmhpd.h>
13 #include <dt-bindings/power/qcom-rpmpd.h>
14 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
17 #address-cells = <2>;
18 #size-cells = <2>;
19 interrupt-parent = <&intc>;
[all …]
|
| D | sdm845-cheza.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
8 #include <dt-bindings/input/input.h>
9 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
25 stdout-path = "serial0:115200n8";
29 compatible = "pwm-backlight";
31 enable-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
32 power-supply = <&ppvar_sys>;
33 pinctrl-names = "default";
34 pinctrl-0 = <&ap_edp_bklten>;
37 /* FIXED REGULATORS - parents above children */
[all …]
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/arm/msm/ |
| D | qcom,idle-state.txt | 3 ARM provides idle-state node to define the cpuidle states, as defined in [1].
4 cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
5 states. Idle states have different enter/exit latency and residency values.
6 The idle states supported by the QCOM SoC are defined as -
44 code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
50 be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
52 power modes possible at this state is vast, the exit latency and the residency
58 The idle-state for QCOM SoCs are distinguished by the compatible property of
59 the idle-states device node.
61 The devicetree representation of the idle state should be -
[all …]
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/arm/msm/ |
| D | qcom,idle-state.txt | 3 ARM provides idle-state node to define the cpuidle states, as defined in [1].
4 cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
5 states. Idle states have different enter/exit latency and residency values.
6 The idle states supported by the QCOM SoC are defined as -
44 code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
50 be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
52 power modes possible at this state is vast, the exit latency and the residency
58 The idle-state for QCOM SoCs are distinguished by the compatible property of
59 the idle-states device node.
61 The devicetree representation of the idle state should be -
[all …]
|
| /kernel/linux/linux-5.10/drivers/cpuidle/ |
| D | dt_idle_states.c | 1 // SPDX-License-Identifier: GPL-2.0-only
9 #define pr_fmt(fmt) "DT idle-states: " fmt
33 idle_state->enter = match_id->data; in init_state_node()
39 idle_state->enter_s2idle = match_id->data; in init_state_node()
41 err = of_property_read_u32(state_node, "wakeup-latency-us", in init_state_node()
42 &idle_state->exit_latency); in init_state_node()
46 err = of_property_read_u32(state_node, "entry-latency-us", in init_state_node()
49 pr_debug(" * %pOF missing entry-latency-us property\n", in init_state_node()
51 return -EINVAL; in init_state_node()
54 err = of_property_read_u32(state_node, "exit-latency-us", in init_state_node()
[all …]
|
| /kernel/linux/linux-6.6/drivers/cpuidle/ |
| D | dt_idle_states.c | 1 // SPDX-License-Identifier: GPL-2.0-only
9 #define pr_fmt(fmt) "DT idle-states: " fmt
32 idle_state->enter = match_id->data; in init_state_node()
38 idle_state->enter_s2idle = match_id->data; in init_state_node()
40 err = of_property_read_u32(state_node, "wakeup-latency-us", in init_state_node()
41 &idle_state->exit_latency); in init_state_node()
45 err = of_property_read_u32(state_node, "entry-latency-us", in init_state_node()
48 pr_debug(" * %pOF missing entry-latency-us property\n", in init_state_node()
50 return -EINVAL; in init_state_node()
53 err = of_property_read_u32(state_node, "exit-latency-us", in init_state_node()
[all …]
|
| /kernel/linux/linux-5.10/drivers/cpuidle/governors/ |
| D | menu.c | 1 // SPDX-License-Identifier: GPL-2.0-only
3 * menu.c - the menu idle governor
5 * Copyright (C) 2006-2007 Adam Belay <abelay@novell.com>
40 * -----------------------
43 * provides us this duration in the "target_residency" field. So all that we
68 * Repeatable-interval-detector
69 * ----------------------------
79 * ---------------------------
88 * This rule-of-thumb is implemented using a performance-multiplier:
127 * This allows us to calculate in which_bucket()
[all …]
|
| /kernel/linux/linux-5.10/arch/arm64/boot/dts/arm/ |
| D | juno-r2.dts | 9 /dts-v1/;
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include "juno-base.dtsi"
13 #include "juno-cs-r1r2.dtsi"
17 compatible = "arm,juno-r2", "arm,juno", "arm,vexpress";
18 interrupt-parent = <&gic>;
19 #address-cells = <2>;
20 #size-cells = <2>;
27 stdout-path = "serial0:115200n8";
31 compatible = "arm,psci-0.2";
[all …]
|
| D | juno.dts | 4 * Copyright (c) 2013-2014 ARM Ltd.
9 /dts-v1/;
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include "juno-base.dtsi"
17 interrupt-parent = <&gic>;
18 #address-cells = <2>;
19 #size-cells = <2>;
26 stdout-path = "serial0:115200n8";
30 compatible = "arm,psci-0.2";
35 #address-cells = <2>;
[all …]
|
| D | juno-r1.dts | 9 /dts-v1/;
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include "juno-base.dtsi"
13 #include "juno-cs-r1r2.dtsi"
17 compatible = "arm,juno-r1", "arm,juno", "arm,vexpress";
18 interrupt-parent = <&gic>;
19 #address-cells = <2>;
20 #size-cells = <2>;
27 stdout-path = "serial0:115200n8";
31 compatible = "arm,psci-0.2";
[all …]
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/arm/ |
| D | juno-r2.dts | 9 /dts-v1/;
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include <dt-bindings/arm/coresight-cti-dt.h>
13 #include "juno-base.dtsi"
14 #include "juno-cs-r1r2.dtsi"
18 compatible = "arm,juno-r2", "arm,juno", "arm,vexpress";
19 interrupt-parent = <&gic>;
20 #address-cells = <2>;
21 #size-cells = <2>;
28 stdout-path = "serial0:115200n8";
[all …]
|
| D | juno.dts | 4 * Copyright (c) 2013-2014 ARM Ltd.
9 /dts-v1/;
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include <dt-bindings/arm/coresight-cti-dt.h>
13 #include "juno-base.dtsi"
18 interrupt-parent = <&gic>;
19 #address-cells = <2>;
20 #size-cells = <2>;
27 stdout-path = "serial0:115200n8";
31 compatible = "arm,psci-0.2";
[all …]
|
| D | juno-r1.dts | 9 /dts-v1/;
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include <dt-bindings/arm/coresight-cti-dt.h>
13 #include "juno-base.dtsi"
14 #include "juno-cs-r1r2.dtsi"
18 compatible = "arm,juno-r1", "arm,juno", "arm,vexpress";
19 interrupt-parent = <&gic>;
20 #address-cells = <2>;
21 #size-cells = <2>;
28 stdout-path = "serial0:115200n8";
[all …]
|