Home
last modified time | relevance | path

Searched +full:nosleep +full:- +full:mode (Results 1 – 25 of 43) sorted by relevance

12

/kernel/linux/linux-5.10/Documentation/devicetree/bindings/input/rmi4/
Drmi_f01.txt10 http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
13 - syna,nosleep-mode: If set the device will run at full power without sleeping.
14 nosleep has 3 modes, 0 will not change the default
15 setting, 1 will disable nosleep (allow sleeping),
16 and 2 will enable nosleep (disabling sleep).
17 - syna,wakeup-threshold: Defines the amplitude of the disturbance to the
20 - syna,doze-holdoff-ms: The delay to wait after the last finger lift and the
22 - syna,doze-interval-ms: The time period that the device sleeps between finger
29 rmi4-i2c-dev@2c {
30 compatible = "syna,rmi4-i2c";
[all …]
Drmi_spi.txt10 - compatible: syna,rmi4-spi
11 - reg: Chip select address for the device
12 - #address-cells: Set to 1 to indicate that the function child nodes
14 - #size-cells: Set to 0 to indicate that the function child nodes do not
18 - interrupts: interrupt which the rmi device is connected to.
19 See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
21 - spi-rx-delay-us: microsecond delay after a read transfer.
22 - spi-tx-delay-us: microsecond delay after a write transfer.
33 rmi4-spi-dev@0 {
34 compatible = "syna,rmi4-spi";
[all …]
Drmi_i2c.txt10 - compatible: syna,rmi4-i2c
11 - reg: I2C address
12 - #address-cells: Set to 1 to indicate that the function child nodes
14 - #size-cells: Set to 0 to indicate that the function child nodes do not
18 - interrupts: interrupt which the rmi device is connected to.
19 See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
21 - syna,reset-delay-ms: The number of milliseconds to wait after resetting the
24 - syna,startup-delay-ms: The number of milliseconds to wait after powering on
27 - vdd-supply: VDD power supply.
30 - vio-supply: VIO power supply
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/input/
Dsyna,rmi4.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jason A. Donenfeld <Jason@zx2c4.com>
11 - Matthias Schiffer <matthias.schiffer@ew.tq-group.com
12 - Vincent Huang <vincent.huang@tw.synaptics.com>
22 - syna,rmi4-i2c
23 - syna,rmi4-spi
28 '#address-cells':
31 '#size-cells':
[all …]
/kernel/linux/linux-5.10/arch/arm64/boot/dts/freescale/
Dimx8mq-zii-ultra-rmb3.dts1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
6 /dts-v1/;
8 #include "imx8mq-zii-ultra.dtsi"
12 compatible = "zii,imx8mq-ultra-rmb3", "zii,imx8mq-ultra", "fsl,imx8mq";
16 pinctrl-names = "default";
17 pinctrl-0 = <&pinctrl_ecspi1>;
18 cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
20 #address-cells = <1>;
21 #size-cells = <0>;
24 compatible = "st,n25q128a13", "jedec,spi-nor";
[all …]
/kernel/linux/linux-5.10/include/linux/
Drmi.h1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * Copyright (c) 2011-2016 Synaptics Incorporated
21 * struct rmi_2d_axis_alignment - target axis alignment
22 * @swap_axes: set to TRUE if desired to swap x- and y-axis
23 * @flip_x: set to TRUE if desired to flip direction on x-axis
24 * @flip_y: set to TRUE if desired to flip direction on y-axis
25 * @clip_x_low - reported X coordinates below this setting will be clipped to
27 * @clip_x_high - reported X coordinates above this setting will be clipped to
29 * @clip_y_low - reported Y coordinates below this setting will be clipped to
31 * @clip_y_high - reported Y coordinates above this setting will be clipped to
[all …]
/kernel/linux/linux-6.6/include/linux/
Drmi.h1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * Copyright (c) 2011-2016 Synaptics Incorporated
21 * struct rmi_2d_axis_alignment - target axis alignment
22 * @swap_axes: set to TRUE if desired to swap x- and y-axis
23 * @flip_x: set to TRUE if desired to flip direction on x-axis
24 * @flip_y: set to TRUE if desired to flip direction on y-axis
25 * @clip_x_low - reported X coordinates below this setting will be clipped to
27 * @clip_x_high - reported X coordinates above this setting will be clipped to
29 * @clip_y_low - reported Y coordinates below this setting will be clipped to
31 * @clip_y_high - reported Y coordinates above this setting will be clipped to
[all …]
/kernel/linux/linux-5.10/drivers/input/rmi4/
Drmi_f01.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (c) 2011-2016 Synaptics Incorporated
64 /* The device is in bootloader mode */
70 * Sleep mode controls power management on the device and affects all
81 * This bit disables whatever sleep mode may be selected by the sleep_mode
87 * When this bit is set, the touch controller employs a noise-filtering
106 * @ctrl0 - see the bit definitions above.
107 * @doze_interval - controls the interval between checks for finger presence
108 * when the touch sensor is in doze mode, in units of 10ms.
109 * @wakeup_threshold - controls the capacitance threshold at which the touch
[all …]
/kernel/linux/linux-6.6/drivers/input/rmi4/
Drmi_f01.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (c) 2011-2016 Synaptics Incorporated
64 /* The device is in bootloader mode */
70 * Sleep mode controls power management on the device and affects all
81 * This bit disables whatever sleep mode may be selected by the sleep_mode
87 * When this bit is set, the touch controller employs a noise-filtering
106 * struct f01_device_control - controls basic sensor functions
110 * when the touch sensor is in doze mode, in units of 10ms.
155 dev_err(&rmi_dev->dev, in rmi_f01_read_properties()
164 props->manufacturer_id = queries[0]; in rmi_f01_read_properties()
[all …]
/kernel/linux/linux-5.10/tools/perf/Documentation/
Dperf-ftrace.txt1 perf-ftrace(1)
5 ----
6 perf-ftrace - simple wrapper for kernel's ftrace functionality
10 --------
15 -----------
23 -------
25 -t::
26 --tracer=::
27 Tracer to use when neither -G nor -F option is not
30 -v::
[all …]
/kernel/linux/linux-6.6/tools/perf/Documentation/
Dperf-ftrace.txt1 perf-ftrace(1)
5 ----
6 perf-ftrace - simple wrapper for kernel's ftrace functionality
10 --------
15 -----------
29 --------------
31 -p::
32 --pid=::
35 --tid=::
38 -a::
[all …]
/kernel/linux/linux-6.6/arch/arm64/boot/dts/freescale/
Dimx8mq-zii-ultra-rmb3.dts1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
6 /dts-v1/;
8 #include "imx8mq-zii-ultra.dtsi"
12 compatible = "zii,imx8mq-ultra-rmb3", "zii,imx8mq-ultra", "fsl,imx8mq";
15 compatible = "simple-audio-card";
16 simple-audio-card,name = "front";
17 simple-audio-card,format = "i2s";
18 simple-audio-card,bitclock-master = <&sound1_codec>;
19 simple-audio-card,frame-master = <&sound1_codec>;
20 simple-audio-card,widgets =
[all …]
/kernel/linux/linux-6.6/arch/arm64/boot/dts/qcom/
Dmsm8916-longcheer-l8150.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-pm8916.dtsi"
6 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/input/input.h>
8 #include <dt-bindings/interrupt-controller/irq.h>
9 #include <dt-bindings/leds/common.h>
13 compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
14 chassis-type = "handset";
23 stdout-path = "serial0";
[all …]
Dmsm8953-xiaomi-vince.dts1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
11 #include <dt-bindings/leds/common.h>
13 /delete-node/ &adsp_fw_mem;
14 /delete-node/ &cont_splash_mem;
15 /delete-node/ &qseecom_mem;
16 /delete-node/ &wcnss_fw_mem;
21 chassis-type = "handset";
22 qcom,msm-id = <293 0>;
23 qcom,board-id = <0x1000b 0x08>;
[all …]
Dmsm8916-huawei-g7.dts1 // SPDX-License-Identifier: GPL-2.0-only
6 /dts-v1/;
8 #include "msm8916-pm8916.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/interrupt-controller/irq.h>
12 #include <dt-bindings/leds/common.h>
13 #include <dt-bindings/sound/apq8016-lpass.h>
16 * Note: The original firmware from Huawei can only boot 32-bit kernels.
17 * To boot this device tree using arm64 it is necessary to flash 64-bit TZ/HYP
[all …]
Dmsm8994-sony-xperia-kitakami.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/gpio-keys.h>
18 * and requires driver-side changes (including CPR, be warned!!).
21 qcom,msm-id = <207 0x20000>, <207 0x20001>;
23 qcom,pmic-id = <0x10009 0x1000a 0x00 0x00>;
25 qcom,board-id = <8 0>;
28 /delete-node/ psci;
30 gpio-keys {
31 compatible = "gpio-keys";
[all …]
Dsdm845-sony-xperia-tama.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
6 #include <dt-bindings/input/input.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
8 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
15 qcom,msm-id = <321 0x20001>; /* SDM845 v2.1 */
16 qcom,board-id = <8 0>;
24 stdout-path = "serial0:115200n8";
27 gpio-keys {
28 compatible = "gpio-keys";
30 pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &vol_up_n>;
[all …]
Dsdm845-xiaomi-polaris.dts1 // SPDX-License-Identifier: BSD-3-Clause
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
12 #include <dt-bindings/input/linux-event-codes.h>
13 #include <dt-bindings/sound/qcom,q6afe.h>
14 #include <dt-bindings/sound/qcom,q6asm.h>
16 #include "sdm845-wcd9340.dtsi"
25 /delete-node/ &rmtfs_mem;
[all …]
Dsdm845-oneplus-common.dtsi1 // SPDX-License-Identifier: GPL-2.0
8 /dts-v1/;
10 #include <dt-bindings/input/linux-event-codes.h>
11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
12 #include <dt-bindings/sound/qcom,q6afe.h>
13 #include <dt-bindings/sound/qcom,q6asm.h>
16 #include "sdm845-wcd9340.dtsi"
20 /delete-node/ &rmtfs_mem;
29 stdout-path = "serial0:115200n8";
32 gpio-hall-sensor {
[all …]
/kernel/linux/linux-6.6/arch/arm/boot/dts/qcom/
Dqcom-apq8026-huawei-sturgeon.dts1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include "qcom-msm8226.dtsi"
10 #include <dt-bindings/input/ti-drv260x.h>
12 /delete-node/ &adsp_region;
17 chassis-type = "watch";
18 qcom,msm-id = <199 0x20000>;
19 qcom,board-id = <8 4>;
21 reserved-memory {
24 no-map;
[all …]
Dqcom-apq8026-lg-lenok.dts1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include "qcom-msm8226.dtsi"
11 /delete-node/ &adsp_region;
16 chassis-type = "watch";
17 qcom,board-id = <132 0x0a>;
18 qcom,msm-id = <199 0x20000>;
26 stdout-path = "serial0:115200n8";
29 reserved-memory {
32 no-map;
[all …]
Dqcom-msm8974pro-oneplus-bacon.dts1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974pro.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
11 chassis-type = "handset";
12 qcom,msm-id = <194 0x10000>;
13 qcom,board-id = <8 0>;
20 stdout-path = "serial0:115200n8";
23 gpio-keys {
24 compatible = "gpio-keys";
[all …]
Dqcom-msm8974-sony-xperia-rhine.dtsi1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/leds/common.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
15 stdout-path = "serial0:115200n8";
18 gpio-keys {
19 compatible = "gpio-keys";
21 pinctrl-names = "default";
22 pinctrl-0 = <&gpio_keys_pin_a>;
[all …]
/kernel/linux/linux-6.6/arch/arm64/boot/dts/mediatek/
Dmt6795-sony-xperia-m5.dts1 // SPDX-License-Identifier: GPL-2.0-only
7 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
14 compatible = "sony,xperia-m5", "mediatek,mt6795";
15 chassis-type = "handset";
30 reserved_memory: reserved-memory {
31 #address-cells = <2>;
32 #size-cells = <2>;
38 no-map;
42 preloader-region@44800000 {
[all …]
/kernel/linux/linux-5.10/arch/arm/boot/dts/
Dqcom-msm8974-sony-xperia-honami.dts1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974.dtsi"
3 #include "qcom-pm8841.dtsi"
4 #include "qcom-pm8941.dtsi"
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
11 compatible = "sony,xperia-honami", "qcom,msm8974";
18 stdout-path = "serial0:115200n8";
21 gpio-keys {
[all …]

12