Searched full:optimum (Results 1 – 25 of 74) sorted by relevance
123
| /kernel/linux/linux-5.10/include/linux/ |
| D | rational.h | 8 * e.g. when calculating optimum numerator/denominator pairs for
|
| /kernel/linux/linux-6.6/include/linux/ |
| D | rational.h | 8 * e.g. when calculating optimum numerator/denominator pairs for
|
| /kernel/linux/linux-5.10/include/linux/mfd/ |
| D | ac100.h | 106 #define AC100_ADC_DAP_OPT 0x95 /* AGC Optimum */
126 #define AC100_DAC_DAP_OPT 0xb1 /* DRC optimum */
|
| /kernel/linux/linux-6.6/include/linux/mfd/ |
| D | ac100.h | 106 #define AC100_ADC_DAP_OPT 0x95 /* AGC Optimum */
126 #define AC100_DAC_DAP_OPT 0xb1 /* DRC optimum */
|
| /kernel/linux/linux-5.10/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-isl29501 | 7 which sets the analog signal levels at an optimum
|
| D | configfs-usb-gadget-uvc | 207 bDefaultFrameIndex optimum frame index for this stream
261 bDefaultFrameIndex optimum frame index for this stream
|
| /kernel/linux/linux-6.6/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-isl29501 | 7 which sets the analog signal levels at an optimum
|
| D | configfs-usb-gadget-uvc | 255 bDefaultFrameIndex optimum frame index for this stream
309 bDefaultFrameIndex optimum frame index for this stream
|
| /kernel/linux/linux-5.10/drivers/ide/ |
| D | Kconfig | 359 speeds and to configure the chip to optimum performance.
384 optimum performance.
393 and to configure the chip to optimum performance.
507 configure the chip to optimum performance.
633 configure the chip to optimum performance.
|
| /kernel/linux/linux-6.6/Documentation/scsi/ |
| D | BusLogic.rst | 307 may be used to load "Optimum Performance" settings which allow UltraSCSI
310 the "Optimum Performance" settings are loaded.
377 used to load "Optimum Performance" settings which allow UltraSCSI speed to be
380 "Optimum Performance" settings are loaded.
|
| /kernel/linux/linux-5.10/arch/powerpc/sysdev/ |
| D | fsl_85xx_cache_ctlr.h | 24 #define L2SRAM_OPTIMAL_SZ_SHIFT 0x00000003 /* Optimum size for L2SRAM */
|
| /kernel/linux/linux-5.10/Documentation/scsi/ |
| D | BusLogic.rst | 313 may be used to load "Optimum Performance" settings which allow UltraSCSI
316 the "Optimum Performance" settings are loaded.
383 used to load "Optimum Performance" settings which allow UltraSCSI speed to be
386 "Optimum Performance" settings are loaded.
|
| /kernel/linux/linux-6.6/drivers/accel/ivpu/ |
| D | ivpu_hw.h | 51 * Pll ratio for the efficiency frequency. The VPU has optimum
|
| /kernel/linux/linux-6.6/arch/alpha/lib/ |
| D | ev6-copy_page.S | 29 conditions were such that I could not reach this optimum rate on
|
| /kernel/linux/linux-5.10/arch/alpha/lib/ |
| D | ev6-copy_page.S | 29 conditions were such that I could not reach this optimum rate on
|
| /kernel/linux/linux-5.10/drivers/scsi/aic7xxx/ |
| D | queue.h | 42 * macro for this purpose for optimum efficiency. A singly-linked list may
53 * should use the explicit macro for this purpose for optimum efficiency.
|
| /kernel/linux/linux-6.6/drivers/scsi/aic7xxx/ |
| D | queue.h | 42 * macro for this purpose for optimum efficiency. A singly-linked list may
53 * should use the explicit macro for this purpose for optimum efficiency.
|
| /kernel/linux/linux-6.6/drivers/net/wireless/ti/wlcore/ |
| D | conf.h | 981 * Minimum required free tx memory blocks in order to assure optimum
989 * Minimum required free rx memory blocks in order to assure optimum
|
| /kernel/linux/linux-5.10/drivers/net/wireless/ti/wlcore/ |
| D | conf.h | 981 * Minimum required free tx memory blocks in order to assure optimum
989 * Minimum required free rx memory blocks in order to assure optimum
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/pci/ |
| D | nvidia,tegra194-pcie.txt | 109 port to exchange optimum number of FC (Flow Control) credits with
|
| /kernel/linux/linux-6.6/drivers/usb/phy/ |
| D | phy-ab8500-usb.c | 193 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", in ab8500_usb_regulator_enable()
233 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", in ab8500_usb_regulator_disable()
|
| /kernel/linux/linux-5.10/drivers/usb/phy/ |
| D | phy-ab8500-usb.c | 193 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", in ab8500_usb_regulator_enable()
233 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", in ab8500_usb_regulator_disable()
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/micrel/ |
| D | ks8851_par.c | 90 * bus. To maintain optimum performance, the bus endianness should be set
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/pci/ |
| D | nvidia,tegra194-pcie.yaml | 155 optimum number of FC (Flow Control) credits with downstream devices:
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/micrel/ |
| D | ks8851_par.c | 88 * bus. To maintain optimum performance, the bus endianness should be set
|
123