Home
last modified time | relevance | path

Searched +full:reset +full:- +full:snvs +full:- +full:powered (Results 1 – 25 of 32) sorted by relevance

12

/kernel/linux/linux-5.10/Documentation/devicetree/bindings/mfd/
Drohm,bd71847-pmic.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/mfd/rohm,bd71847-pmic.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
14 single-core, dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is
18 …/www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applica…
19 …//www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applic…
24 - rohm,bd71847
25 - rohm,bd71850
[all …]
Drohm,bd71837-pmic.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/mfd/rohm,bd71837-pmic.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
13 BD71837MWV is programmable Power Management ICs for powering single-core,
14 dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for low
18 …/www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applica…
35 "#clock-cells":
38 # The BD718x7 supports two different HW states as reset target states. States
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/mfd/
Drohm,bd71847-pmic.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/mfd/rohm,bd71847-pmic.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Matti Vaittinen <mazziesaccount@gmail.com>
14 single-core, dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is
18 …/www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applica…
19 …//www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applic…
24 - rohm,bd71847
25 - rohm,bd71850
[all …]
Drohm,bd71837-pmic.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/mfd/rohm,bd71837-pmic.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Matti Vaittinen <mazziesaccount@gmail.com>
13 BD71837MWV is programmable Power Management ICs for powering single-core,
14 dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for low
18 …/www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applica…
35 clock-names:
38 "#clock-cells":
[all …]
/kernel/linux/linux-6.6/arch/arm64/boot/dts/freescale/
Dimx8mn-ddr4-evk.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
9 #include "imx8mn-evk.dtsi"
13 compatible = "fsl,imx8mn-ddr4-evk", "fsl,imx8mn";
17 cpu-supply = <&buck2_reg>;
21 cpu-supply = <&buck2_reg>;
25 cpu-supply = <&buck2_reg>;
29 cpu-supply = <&buck2_reg>;
33 operating-points-v2 = <&ddrc_opp_table>;
35 ddrc_opp_table: opp-table {
[all …]
Dimx8mn-bsh-smm-s2-common.dtsi1 // SPDX-License-Identifier: GPL-2.0+
7 /dts-v1/;
13 stdout-path = &uart4;
16 fec_supply: fec-supply-en {
17 compatible = "regulator-fixed";
18 vin-supply = <&buck4_reg>;
19 regulator-name = "tja1101_en";
20 regulator-min-microvolt = <3300000>;
21 regulator-max-microvolt = <3300000>;
23 enable-active-high;
[all …]
Dimx8mq-librem5-devkit.dts1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright 2018-2019 Purism SPC
6 /dts-v1/;
8 #include "dt-bindings/input/input.h"
9 #include <dt-bindings/interrupt-controller/irq.h>
10 #include <dt-bindings/leds/common.h>
11 #include "dt-bindings/pwm/pwm.h"
12 #include "dt-bindings/usb/pd.h"
17 compatible = "purism,librem5-devkit", "fsl,imx8mq";
19 backlight_dsi: backlight-dsi {
[all …]
Dimx8mn-beacon-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
14 compatible = "mmc-pwrseq-simple";
15 pinctrl-names = "default";
16 pinctrl-0 = <&pinctrl_usdhc1_gpio>;
17 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
19 clock-names = "ext_clock";
20 post-power-on-delay-ms = <80>;
30 cpu-supply = <&buck2_reg>;
34 cpu-supply = <&buck2_reg>;
38 cpu-supply = <&buck2_reg>;
[all …]
Dimx8mm-innocomm-wb15.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
7 #include <dt-bindings/phy/phy-imx8-pcie.h>
10 reg_modem: regulator-modem {
11 compatible = "regulator-fixed";
12 pinctrl-names = "default";
13 pinctrl-0 = <&pinctrl_modem_regulator>;
14 regulator-min-microvolt = <3300000>;
15 regulator-max-microvolt = <3300000>;
16 regulator-name = "epdev_on";
18 enable-active-high;
[all …]
Dimx8mm-beacon-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
13 compatible = "mmc-pwrseq-simple";
14 pinctrl-names = "default";
15 pinctrl-0 = <&pinctrl_usdhc1_gpio>;
16 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
18 clock-names = "ext_clock";
19 post-power-on-delay-ms = <80>;
29 cpu-supply = <&buck2_reg>;
33 cpu-supply = <&buck2_reg>;
37 cpu-supply = <&buck2_reg>;
[all …]
Dimx8mm-var-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
10 model = "Variscite VAR-SOM-MX8MM module";
11 compatible = "variscite,var-som-mx8mm", "fsl,imx8mm";
14 stdout-path = &uart4;
22 reg_eth_phy: regulator-eth-phy {
23 compatible = "regulator-fixed";
24 pinctrl-names = "default";
25 pinctrl-0 = <&pinctrl_reg_eth_phy>;
26 regulator-name = "eth_phy_pwr";
27 regulator-min-microvolt = <3300000>;
[all …]
Dimx8mn-var-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 * Copyright 2019-2020 Variscite Ltd.
11 model = "Variscite VAR-SOM-MX8MN module";
12 compatible = "variscite,var-som-mx8mn", "fsl,imx8mn";
15 stdout-path = &uart4;
23 reg_eth_phy: regulator-eth-phy {
24 compatible = "regulator-fixed";
25 pinctrl-names = "default";
26 pinctrl-0 = <&pinctrl_reg_eth_phy>;
27 regulator-name = "eth_phy_pwr";
[all …]
Dimx8mm-evk.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include <dt-bindings/phy/phy-imx8-pcie.h>
9 #include <dt-bindings/usb/pd.h>
14 stdout-path = &uart2;
22 hdmi-connector {
23 compatible = "hdmi-connector";
29 remote-endpoint = <&adv7535_out>;
35 compatible = "gpio-leds";
36 pinctrl-names = "default";
[all …]
Dimx8mm-emcon.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
7 /dts-v1/;
13 stdout-path = &uart1;
17 compatible = "gpio-leds";
18 pinctrl-names = "default";
19 pinctrl-0 = <&pinctrl_gpio_led>;
21 led-green {
24 default-state = "on";
25 linux,default-trigger = "heartbeat";
28 led-red {
[all …]
Dimx8mq-librem5.dtsi1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright 2018-2020 Purism SPC
6 /dts-v1/;
8 #include "dt-bindings/input/input.h"
9 #include <dt-bindings/interrupt-controller/irq.h>
10 #include <dt-bindings/leds/common.h>
11 #include "dt-bindings/pwm/pwm.h"
12 #include "dt-bindings/usb/pd.h"
18 chassis-type = "handset";
20 backlight_dsi: backlight-dsi {
[all …]
/kernel/linux/linux-5.10/arch/arm64/boot/dts/freescale/
Dimx8mn-ddr4-evk.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
9 #include "imx8mn-evk.dtsi"
13 compatible = "fsl,imx8mn-ddr4-evk", "fsl,imx8mn";
17 cpu-supply = <&buck2_reg>;
21 cpu-supply = <&buck2_reg>;
25 cpu-supply = <&buck2_reg>;
29 cpu-supply = <&buck2_reg>;
33 operating-points-v2 = <&ddrc_opp_table>;
35 ddrc_opp_table: opp-table {
[all …]
Dimx8mm-evk.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include <dt-bindings/usb/pd.h>
13 stdout-path = &uart2;
22 compatible = "gpio-leds";
23 pinctrl-names = "default";
24 pinctrl-0 = <&pinctrl_gpio_led>;
29 default-state = "on";
33 reg_usdhc2_vmmc: regulator-usdhc2 {
34 compatible = "regulator-fixed";
[all …]
Dimx8mm-beacon-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
8 compatible = "mmc-pwrseq-simple";
9 pinctrl-names = "default";
10 pinctrl-0 = <&pinctrl_usdhc1_gpio>;
11 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
13 clock-names = "ext_clock";
14 post-power-on-delay-ms = <80>;
24 cpu-supply = <&buck2_reg>;
28 operating-points-v2 = <&ddrc_opp_table>;
30 ddrc_opp_table: opp-table {
[all …]
Dimx8mq-librem5-devkit.dts1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright 2018-2019 Purism SPC
6 /dts-v1/;
8 #include "dt-bindings/input/input.h"
9 #include <dt-bindings/interrupt-controller/irq.h>
10 #include "dt-bindings/pwm/pwm.h"
11 #include "dt-bindings/usb/pd.h"
16 compatible = "purism,librem5-devkit", "fsl,imx8mq";
18 backlight_dsi: backlight-dsi {
19 compatible = "pwm-backlight";
[all …]
Dimx8mm-var-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
10 model = "Variscite VAR-SOM-MX8MM module";
11 compatible = "variscite,var-som-mx8mm", "fsl,imx8mm";
14 stdout-path = &uart4;
22 reg_eth_phy: regulator-eth-phy {
23 compatible = "regulator-fixed";
24 pinctrl-names = "default";
25 pinctrl-0 = <&pinctrl_reg_eth_phy>;
26 regulator-name = "eth_phy_pwr";
27 regulator-min-microvolt = <3300000>;
[all …]
Dimx8mn-var-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 * Copyright 2019-2020 Variscite Ltd.
11 model = "Variscite VAR-SOM-MX8MN module";
12 compatible = "variscite,var-som-mx8mn", "fsl,imx8mn";
15 stdout-path = &uart4;
23 reg_eth_phy: regulator-eth-phy {
24 compatible = "regulator-fixed";
25 pinctrl-names = "default";
26 pinctrl-0 = <&pinctrl_reg_eth_phy>;
27 regulator-name = "eth_phy_pwr";
[all …]
Dimx8mq-librem5.dtsi1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright 2018-2020 Purism SPC
6 /dts-v1/;
8 #include "dt-bindings/input/input.h"
9 #include <dt-bindings/interrupt-controller/irq.h>
10 #include "dt-bindings/pwm/pwm.h"
11 #include "dt-bindings/usb/pd.h"
18 backlight_dsi: backlight-dsi {
19 compatible = "led-backlight";
23 pmic_osc: clock-pmic {
[all …]
/kernel/linux/linux-5.10/drivers/regulator/
Dbd718x7-regulator.c1 // SPDX-License-Identifier: GPL-2.0
3 // bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver
9 #include <linux/mfd/rohm-bd718x7.h>
50 * controlled by software - or by PMIC internal HW state machine. Whether
51 * regulator should be under SW or HW control can be defined from device-tree.
95 dev_dbg(&rdev->dev, "Buck[%d] Set Ramp = %d\n", id + 1, in bd718xx_buck1234_set_ramp_delay()
112 dev_err(&rdev->dev, in bd718xx_buck1234_set_ramp_delay()
114 rdev->desc->name, ramp_delay); in bd718xx_buck1234_set_ramp_delay()
117 return regmap_update_bits(rdev->regmap, BD718XX_REG_BUCK1_CTRL + id, in bd718xx_buck1234_set_ramp_delay()
127 * Note for next hacker - these PMICs have a register where the HW state can be
[all …]
/kernel/linux/linux-6.6/drivers/regulator/
Dbd718x7-regulator.c1 // SPDX-License-Identifier: GPL-2.0
3 // bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver
9 #include <linux/mfd/rohm-bd718x7.h>
50 * controlled by software - or by PMIC internal HW state machine. Whether
51 * regulator should be under SW or HW control can be defined from device-tree.
102 * Note for next hacker - these PMICs have a register where the HW state can be
103 * read. If assuming RUN appears to be false in your use-case - you can
122 ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val); in bd71837_get_buck34_enable_hwctrl()
137 * guarantee minimum of 1ms sleep - it shouldn't matter if we in voltage_change_done()
142 ret = regmap_clear_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2, in voltage_change_done()
[all …]
/kernel/linux/patches/linux-5.10/imx8mm_patch/patches/drivers/
D0033_linux_drivers_soc_scsi_spi_tee_thermal.patch7 Change-Id: I1ba947d26a24ae6708961a663867e136c1171c8d
9 diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
11 --- a/drivers/scsi/scsi_error.c
13 @@ -63,6 +63,13 @@ static int scsi_eh_try_stu(struct scsi_cmnd *scmd);
23 +/* called with shost->host_lock held */
26 lockdep_assert_held(shost->host_lock);
27 @@ -72,6 +79,11 @@ void scsi_eh_wakeup(struct Scsi_Host *shost)
28 wake_up_process(shost->ehandler);
31 + } else if ((shost->host_failed > 0) || (sg_io_buffer_hack != NULL)) {
33 + wake_up_process(shost->ehandler);
[all …]

12