Home
last modified time | relevance | path

Searched +full:rgmii +full:- +full:txid (Results 1 – 25 of 60) sorted by relevance

123

/kernel/linux/linux-6.6/Documentation/devicetree/bindings/net/
Dcpsw.txt2 ------------------------------------------------------
5 - compatible : Should be one of the below:-
7 "ti,am335x-cpsw" for AM335x controllers
8 "ti,am4372-cpsw" for AM437x controllers
9 "ti,dra7-cpsw" for DRA7x controllers
10 - reg : physical base address and size of the cpsw
12 - interrupts : property with a value describing the interrupt
14 - cpdma_channels : Specifies number of channels in CPDMA
15 - ale_entries : Specifies No of entries ALE can hold
16 - bd_ram_size : Specifies internal descriptor RAM size
[all …]
Dethernet-controller.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/ethernet-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - David S. Miller <davem@davemloft.net>
20 local-mac-address:
23 $ref: /schemas/types.yaml#/definitions/uint8-array
27 mac-address:
32 local-mac-address property.
33 $ref: /schemas/types.yaml#/definitions/uint8-array
[all …]
Dadi,adin.yaml1 # SPDX-License-Identifier: GPL-2.0+
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Alexandru Tachici <alexandru.tachici@analog.com>
16 - $ref: ethernet-phy.yaml#
19 adi,rx-internal-delay-ps:
21 RGMII RX Clock Delay used only when PHY operates in RGMII mode with
22 internal delay (phy-mode is 'rgmii-id' or 'rgmii-rxid') in pico-seconds.
26 adi,tx-internal-delay-ps:
28 RGMII TX Clock Delay used only when PHY operates in RGMII mode with
[all …]
Damlogic,meson-dwmac.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/net/amlogic,meson-dwmac.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Neil Armstrong <neil.armstrong@linaro.org>
12 - Martin Blumenstingl <martin.blumenstingl@googlemail.com>
20 - amlogic,meson6-dwmac
21 - amlogic,meson8b-dwmac
22 - amlogic,meson8m2-dwmac
23 - amlogic,meson-gxbb-dwmac
[all …]
Dmotorcomm,yt8xxx.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Frank Sae <frank.sae@motor-comm.com>
13 - $ref: ethernet-phy.yaml#
18 - ethernet-phy-id4f51.e91a
19 - ethernet-phy-id4f51.e91b
21 rx-internal-delay-ps:
23 RGMII RX Clock Delay used only when PHY operates in RGMII mode with
24 internal delay (phy-mode is 'rgmii-id' or 'rgmii-rxid') in pico-seconds.
[all …]
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/
Dcpsw.txt2 ------------------------------------------------------
5 - compatible : Should be one of the below:-
7 "ti,am335x-cpsw" for AM335x controllers
8 "ti,am4372-cpsw" for AM437x controllers
9 "ti,dra7-cpsw" for DRA7x controllers
10 - reg : physical base address and size of the cpsw
12 - interrupts : property with a value describing the interrupt
14 - cpdma_channels : Specifies number of channels in CPDMA
15 - ale_entries : Specifies No of entries ALE can hold
16 - bd_ram_size : Specifies internal descriptor RAM size
[all …]
Dadi,adin.yaml1 # SPDX-License-Identifier: GPL-2.0+
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Alexandru Ardelean <alexandru.ardelean@analog.com>
16 - $ref: ethernet-phy.yaml#
19 adi,rx-internal-delay-ps:
21 RGMII RX Clock Delay used only when PHY operates in RGMII mode with
22 internal delay (phy-mode is 'rgmii-id' or 'rgmii-rxid') in pico-seconds.
26 adi,tx-internal-delay-ps:
28 RGMII TX Clock Delay used only when PHY operates in RGMII mode with
[all …]
Damlogic,meson-dwmac.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
5 $id: "http://devicetree.org/schemas/net/amlogic,meson-dwmac.yaml#"
6 $schema: "http://devicetree.org/meta-schemas/core.yaml#"
11 - Neil Armstrong <narmstrong@baylibre.com>
12 - Martin Blumenstingl <martin.blumenstingl@googlemail.com>
20 - amlogic,meson6-dwmac
21 - amlogic,meson8b-dwmac
22 - amlogic,meson8m2-dwmac
23 - amlogic,meson-gxbb-dwmac
[all …]
Dethernet-controller.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/ethernet-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - David S. Miller <davem@davemloft.net>
16 local-mac-address:
19 $ref: /schemas/types.yaml#definitions/uint8-array
21 - minItems: 6
24 mac-address:
29 local-mac-address property.
[all …]
/kernel/linux/linux-5.10/arch/arm/boot/dts/
Dvf610-zii-dev-rev-b.dts1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
6 /dts-v1/;
7 #include "vf610-zii-dev.dtsi"
11 compatible = "zii,vf610dev-b", "zii,vf610dev", "fsl,vf610";
13 mdio-mux {
14 compatible = "mdio-mux-gpio";
15 pinctrl-0 = <&pinctrl_mdio_mux>;
16 pinctrl-names = "default";
21 mdio-parent-bus = <&mdio1>;
22 #address-cells = <1>;
[all …]
Dkirkwood-l-50.dts1 // SPDX-License-Identifier: GPL-2.0
3 * Check Point L-50 Board Description
7 /dts-v1/;
10 #include "kirkwood-6281.dtsi"
13 model = "Check Point L-50";
14 compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
23 stdout-path = &uart0;
27 pinctrl: pin-controller@10000 {
28 pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
29 pinctrl-names = "default";
[all …]
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/dsa/
Dmt7530.txt6 - compatible: may be compatible = "mediatek,mt7530"
9 - #address-cells: Must be 1.
10 - #size-cells: Must be 0.
11 - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
12 on multi-chip module belong to MT7623A has or the remotely standalone
17 - core-supply: Phandle to the regulator node necessary for the core power.
18 - io-supply: Phandle to the regulator node necessary for the I/O power.
19 See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt
24 - reset-gpios: Should be a gpio specifier for a reset line.
28 - resets : Phandle pointing to the system reset controller with
[all …]
Db53.txt6 - compatible: For external switch chips, compatible string must be exactly one
18 "brcm,bcm11360-srab" and the mandatory "brcm,cygnus-srab" string
21 "brcm,bcm53010-srab"
22 "brcm,bcm53011-srab"
23 "brcm,bcm53012-srab"
24 "brcm,bcm53018-srab"
25 "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string
28 "brcm,bcm11404-srab"
29 "brcm,bcm11407-srab"
30 "brcm,bcm11409-srab"
[all …]
Dsja1105.txt6 - compatible:
8 - "nxp,sja1105e"
9 - "nxp,sja1105t"
10 - "nxp,sja1105p"
11 - "nxp,sja1105q"
12 - "nxp,sja1105r"
13 - "nxp,sja1105s"
18 and the non-SGMII devices, while pin-compatible, are not equal in terms
19 of support for RGMII internal delays (supported on P/Q/R/S, but not on
24 - sja1105,role-mac:
[all …]
/kernel/linux/linux-5.10/Documentation/ABI/testing/
Dsysfs-class-net-phydev24 This attribute contains the 32-bit PHY Identifier as reported
41 <empty> (not available), mii, gmii, sgmii, tbi, rev-mii,
42 rmii, rgmii, rgmii-id, rgmii-rxid, rgmii-txid, rtbi, smii
43 xgmii, moca, qsgmii, trgmii, 1000base-x, 2500base-x, rxaui,
44 xaui, 10gbase-kr, unknown
/kernel/linux/linux-6.6/Documentation/ABI/testing/
Dsysfs-class-net-phydev24 This attribute contains the 32-bit PHY Identifier as reported
41 <empty> (not available), mii, gmii, sgmii, tbi, rev-mii,
42 rmii, rgmii, rgmii-id, rgmii-rxid, rgmii-txid, rtbi, smii
43 xgmii, moca, qsgmii, trgmii, 1000base-x, 2500base-x, rxaui,
44 xaui, 10gbase-kr, unknown
60 32-bit hexadecimal number representing a bit mask of the
/kernel/linux/linux-5.10/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/
Ducc.txt4 - device_type : should be "network", "hldc", "uart", "transparent"
6 - compatible : could be "ucc_geth" or "fsl_atm" and so on.
7 - cell-index : the ucc number(1-8), corresponding to UCCx in UM.
8 - reg : Offset and length of the register set for the device
9 - interrupts : <a b> where a is the interrupt number and b is a
14 - pio-handle : The phandle for the Parallel I/O port configuration.
15 - port-number : for UART drivers, the port number to use, between 0 and 3.
18 CPM UART driver, the port-number is required for the QE UART driver.
19 - soft-uart : for UART drivers, if specified this means the QE UART device
20 driver should use "Soft-UART" mode, which is needed on some SOCs that have
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/
Ducc.txt4 - device_type : should be "network", "hldc", "uart", "transparent"
6 - compatible : could be "ucc_geth" or "fsl_atm" and so on.
7 - cell-index : the ucc number(1-8), corresponding to UCCx in UM.
8 - reg : Offset and length of the register set for the device
9 - interrupts : <a b> where a is the interrupt number and b is a
14 - pio-handle : The phandle for the Parallel I/O port configuration.
15 - port-number : for UART drivers, the port number to use, between 0 and 3.
18 CPM UART driver, the port-number is required for the QE UART driver.
19 - soft-uart : for UART drivers, if specified this means the QE UART device
20 driver should use "Soft-UART" mode, which is needed on some SOCs that have
[all …]
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/net/dsa/
Dmicrochip,lan937x.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - UNGLinuxDriver@microchip.com
13 - $ref: dsa.yaml#/$defs/ethernet-ports
18 - microchip,lan9370
19 - microchip,lan9371
20 - microchip,lan9372
21 - microchip,lan9373
22 - microchip,lan9374
[all …]
Dbrcm,b53.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Florian Fainelli <f.fainelli@gmail.com>
18 - const: brcm,bcm5325
19 - const: brcm,bcm53115
20 - const: brcm,bcm53125
21 - const: brcm,bcm53128
22 - const: brcm,bcm53134
23 - const: brcm,bcm5365
[all …]
Dnxp,sja1105.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at
16 - Vladimir Oltean <vladimir.oltean@nxp.com>
21 - nxp,sja1105e
22 - nxp,sja1105t
23 - nxp,sja1105p
24 - nxp,sja1105q
25 - nxp,sja1105r
[all …]
/kernel/linux/linux-5.10/arch/arm64/boot/dts/allwinner/
Dsun50i-a64-pine64-plus.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 #include "sun50i-a64-pine64.dts"
8 compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
14 pinctrl-names = "default";
15 pinctrl-0 = <&rgmii_pins>;
16 phy-mode = "rgmii-txid";
17 phy-handle = <&ext_rgmii_phy>;
22 ext_rgmii_phy: ethernet-phy@1 {
23 compatible = "ethernet-phy-ieee802.3-c22";
34 regulator-enable-ramp-delay = <100000>;
/kernel/linux/linux-6.6/arch/arm64/boot/dts/allwinner/
Dsun50i-a64-pine64-plus.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 #include "sun50i-a64-pine64.dts"
8 compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
14 pinctrl-names = "default";
15 pinctrl-0 = <&rgmii_pins>;
16 phy-mode = "rgmii-txid";
17 phy-handle = <&ext_rgmii_phy>;
22 ext_rgmii_phy: ethernet-phy@1 {
23 compatible = "ethernet-phy-ieee802.3-c22";
34 regulator-enable-ramp-delay = <100000>;
/kernel/linux/linux-6.6/arch/arm/boot/dts/marvell/
Dkirkwood-l-50.dts1 // SPDX-License-Identifier: GPL-2.0
3 * Check Point L-50 Board Description
7 /dts-v1/;
10 #include "kirkwood-6281.dtsi"
13 model = "Check Point L-50";
14 compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
23 stdout-path = &uart0;
27 pinctrl: pin-controller@10000 {
28 pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
29 pinctrl-names = "default";
[all …]
/kernel/linux/linux-6.6/arch/arm64/boot/dts/qcom/
Dsa8540p-ride.dts1 // SPDX-License-Identifier: BSD-3-Clause
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
13 #include "sa8540p-pmics.dtsi"
17 compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
29 stdout-path = "serial0:115200n8";
34 regulators-0 {
35 compatible = "qcom,pm8150-rpmh-regulators";
36 qcom,pmic-id = "a";
[all …]

123