Searched full:selecting (Results 1 – 25 of 751) sorted by relevance
12345678910>>...31
126 Selecting this option causes mac80211 to print out137 Selecting this option causes mac80211 to print out148 Selecting this option causes mac80211 to print out169 Selecting this option causes mac80211 to print out180 Selecting this option causes mac80211 to print out191 Selecting this option causes mac80211 to print out very204 Selecting this option causes mac80211 to print out very217 Selecting this option causes mac80211 to print out very230 Selecting this option causes mac80211 to print out very243 Selecting this option causes mac80211 to print out very verbose mesh[all …]
32 Selecting this will enable printing of various debug106 Selecting this will offload crypto for users of the120 Selecting this will use CAAM Queue Interface (QI) for sending133 Selecting this will offload ahash for users of the141 Selecting this will allow SEC Public key support for RSA.151 Selecting this will register the SEC4 hardware rng to159 Selecting this will register the SEC hardware prng to169 Selecting this will enable a self-test to run for the
24 Selecting this option will enable support for SH processors that34 Selecting this option will enable support for software FPU emulation.43 Selecting this option will enable support for SH processors that53 Selecting this option will allow the Linux kernel to use SH3 on-chip62 Selecting this option will enable an in-kernel API for manipulating
32 Selecting this will enable printing of various debug106 Selecting this will offload crypto for users of the120 Selecting this will use CAAM Queue Interface (QI) for sending133 Selecting this will offload ahash for users of the141 Selecting this will allow SEC Public key support for RSA.151 Selecting this will register the SEC4 hardware rng to
25 Selecting this option prints more information for Illegal Dependency44 Selecting this option turns on bug checking for the IA-6453 Selecting this option turns on bug checking for the IA-64 irq_save
9 It requires selecting USB ports that should be observed. All available ones are10 listed as separated entries in a "ports" subdirectory. Selecting is handled by13 Please note that this trigger allows selecting multiple USB ports for a single
16 API for selecting the platform profile of these automatic mechanisms.18 Note that this API is only for selecting the platform profile, it is23 Specifically when selecting a high performance profile the actual achieved
62 Selecting this option will enable a DMAR device at boot time if90 Selecting this option will enable by default the scalable mode if103 Selecting this option will enable the performance monitoring
9 Selecting this option will configure the kernel for R2D-PLUS.17 Selecting this option will configure the kernel for R2D-1.
135 file systems will be readable without selecting this option.150 file systems will be readable without selecting this option.165 file systems will be readable without selecting this option.179 file systems will be readable without selecting this option.
77 Selecting this option will add support for the RS232 and RS485386 Selecting this option enables a workaround for a break-detection407 Selecting this option will enable handling of the extra features415 Selecting this option will add support for the integrated serial436 Selecting this option will add support for the alternate register512 Selecting this option will enable handling of the UART found on528 Selecting this option will enable handling of the UART found on537 Selecting this option will enable handling of the Pericom and Acces
176 file systems will be readable without selecting this option.191 file systems will be readable without selecting this option.206 file systems will be readable without selecting this option.220 file systems will be readable without selecting this option.
57 These pins are used for selecting the pull control and schmitt91 group. These pin groups are used for selecting the pinmux113 These pin groups are used for selecting the drive strength126 These pin groups are used for selecting the slew rate
57 These pins are used for selecting the pull control and schmitt85 group. These pin groups are used for selecting the pinmux103 These pin groups are used for selecting the drive strength
76 clock mode. Selecting non-quadrature clock mode will disable85 direction control input, with B = 1 selecting UP Count86 mode and B = 0 selecting Down Count mode.
78 Selecting this option will add support for the RS485 capabilities376 Selecting this option will enable handling of the extra features383 Selecting this option will add support for the integrated serial403 Selecting this option will add support for the alternate register477 Selecting this option will enable handling of the extra features492 Selecting this option will enable handling of the extra features
53 Selecting this option will enable a DMAR device at boot time if81 Selecting this option will enable by default the scalable mode if
95 #P1_PROCHOT and #P2_PROCHOT, respectively. Selecting a value not in this150 are constrained by the hardware. Selecting a value which is not available160 frequency values are constrained by the hardware. Selecting a value which is245 the hardware. Selecting a value which is not available will cause the driver258 The available ramp times are constrained by the hardware. Selecting a value