1menu "Command line interface" 2 3config CMDLINE 4 bool "Support U-Boot commands" 5 default y 6 help 7 Enable U-Boot's command-line functions. This provides a means 8 to enter commands into U-Boot for a wide variety of purposes. It 9 also allows scripts (containing commands) to be executed. 10 Various commands and command categorys can be indivdually enabled. 11 Depending on the number of commands enabled, this can add 12 substantially to the size of U-Boot. 13 14config HUSH_PARSER 15 bool "Use hush shell" 16 depends on CMDLINE 17 help 18 This option enables the "hush" shell (from Busybox) as command line 19 interpreter, thus enabling powerful command line syntax like 20 if...then...else...fi conditionals or `&&' and '||' 21 constructs ("shell scripts"). 22 23 If disabled, you get the old, much simpler behaviour with a somewhat 24 smaller memory footprint. 25 26config CMDLINE_EDITING 27 bool "Enable command line editing" 28 depends on CMDLINE 29 default y 30 help 31 Enable editing and History functions for interactive command line 32 input operations 33 34config AUTO_COMPLETE 35 bool "Enable auto complete using TAB" 36 depends on CMDLINE 37 default y 38 help 39 Enable auto completion of commands using TAB. 40 41config SYS_LONGHELP 42 bool "Enable long help messages" 43 depends on CMDLINE 44 default y if CMDLINE 45 help 46 Defined when you want long help messages included 47 Do not set this option when short of memory. 48 49config SYS_PROMPT 50 string "Shell prompt" 51 default "=> " 52 help 53 This string is displayed in the command line to the left of the 54 cursor. 55 56menu "Autoboot options" 57 58config AUTOBOOT 59 bool "Autoboot" 60 default y 61 help 62 This enables the autoboot. See doc/README.autoboot for detail. 63 64config AUTOBOOT_KEYED 65 bool "Stop autobooting via specific input key / string" 66 default n 67 help 68 This option enables stopping (aborting) of the automatic 69 boot feature only by issuing a specific input key or 70 string. If not enabled, any input key will abort the 71 U-Boot automatic booting process and bring the device 72 to the U-Boot prompt for user input. 73 74config AUTOBOOT_PROMPT 75 string "Autoboot stop prompt" 76 depends on AUTOBOOT_KEYED 77 default "Autoboot in %d seconds\\n" 78 help 79 This string is displayed before the boot delay selected by 80 CONFIG_BOOTDELAY starts. If it is not defined there is no 81 output indicating that autoboot is in progress. 82 83 Note that this define is used as the (only) argument to a 84 printf() call, so it may contain '%' format specifications, 85 provided that it also includes, sepearated by commas exactly 86 like in a printf statement, the required arguments. It is 87 the responsibility of the user to select only such arguments 88 that are valid in the given context. 89 90config AUTOBOOT_ENCRYPTION 91 bool "Enable encryption in autoboot stopping" 92 depends on AUTOBOOT_KEYED 93 default n 94 95config AUTOBOOT_DELAY_STR 96 string "Delay autobooting via specific input key / string" 97 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 98 help 99 This option delays the automatic boot feature by issuing 100 a specific input key or string. If CONFIG_AUTOBOOT_DELAY_STR 101 or the environment variable "bootdelaykey" is specified 102 and this string is received from console input before 103 autoboot starts booting, U-Boot gives a command prompt. The 104 U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is 105 used, otherwise it never times out. 106 107config AUTOBOOT_STOP_STR 108 string "Stop autobooting via specific input key / string" 109 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 110 help 111 This option enables stopping (aborting) of the automatic 112 boot feature only by issuing a specific input key or 113 string. If CONFIG_AUTOBOOT_STOP_STR or the environment 114 variable "bootstopkey" is specified and this string is 115 received from console input before autoboot starts booting, 116 U-Boot gives a command prompt. The U-Boot prompt never 117 times out, even if CONFIG_BOOT_RETRY_TIME is used. 118 119config AUTOBOOT_KEYED_CTRLC 120 bool "Enable Ctrl-C autoboot interruption" 121 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 122 default n 123 help 124 This option allows for the boot sequence to be interrupted 125 by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey". 126 Setting this variable provides an escape sequence from the 127 limited "password" strings. 128 129config AUTOBOOT_STOP_STR_SHA256 130 string "Stop autobooting via SHA256 encrypted password" 131 depends on AUTOBOOT_KEYED && AUTOBOOT_ENCRYPTION 132 help 133 This option adds the feature to only stop the autobooting, 134 and therefore boot into the U-Boot prompt, when the input 135 string / password matches a values that is encypted via 136 a SHA256 hash and saved in the environment. 137 138endmenu 139 140config BUILD_BIN2C 141 bool 142 143comment "Commands" 144 145menu "Info commands" 146 147config CMD_BDI 148 bool "bdinfo" 149 default y 150 help 151 Print board info 152 153config CMD_CONFIG 154 bool "config" 155 select BUILD_BIN2C 156 default SANDBOX 157 help 158 Print ".config" contents. 159 160 If this option is enabled, the ".config" file contents are embedded 161 in the U-Boot image and can be printed on the console by the "config" 162 command. This provides information of which options are enabled on 163 the running U-Boot. 164 165config CMD_CONSOLE 166 bool "coninfo" 167 default y 168 help 169 Print console devices and information. 170 171config CMD_CPU 172 bool "cpu" 173 help 174 Print information about available CPUs. This normally shows the 175 number of CPUs, type (e.g. manufacturer, architecture, product or 176 internal name) and clock frequency. Other information may be 177 available depending on the CPU driver. 178 179config CMD_LICENSE 180 bool "license" 181 select BUILD_BIN2C 182 help 183 Print GPL license text 184 185config CMD_REGINFO 186 bool "reginfo" 187 depends on PPC 188 help 189 Register dump 190 191endmenu 192 193menu "Boot commands" 194 195config CMD_BOOTD 196 bool "bootd" 197 default y 198 help 199 Run the command stored in the environment "bootcmd", i.e. 200 "bootd" does the same thing as "run bootcmd". 201 202config CMD_BOOTM 203 bool "bootm" 204 default y 205 help 206 Boot an application image from the memory. 207 208config CMD_BOOTZ 209 bool "bootz" 210 help 211 Boot the Linux zImage 212 213config CMD_BOOTI 214 bool "booti" 215 depends on ARM64 216 default y 217 help 218 Boot an AArch64 Linux Kernel image from memory. 219 220config CMD_BOOTEFI 221 bool "bootefi" 222 depends on EFI_LOADER 223 default y 224 help 225 Boot an EFI image from memory. 226 227config CMD_BOOTEFI_HELLO_COMPILE 228 bool "Compile a standard EFI hello world binary for testing" 229 depends on CMD_BOOTEFI && (ARM || X86 || RISCV) 230 default y 231 help 232 This compiles a standard EFI hello world application with U-Boot so 233 that it can be used with the test/py testing framework. This is useful 234 for testing that EFI is working at a basic level, and for bringing 235 up EFI support on a new architecture. 236 237 No additional space will be required in the resulting U-Boot binary 238 when this option is enabled. 239 240config CMD_BOOTEFI_HELLO 241 bool "Allow booting a standard EFI hello world for testing" 242 depends on CMD_BOOTEFI_HELLO_COMPILE 243 help 244 This adds a standard EFI hello world application to U-Boot so that 245 it can be used with the 'bootefi hello' command. This is useful 246 for testing that EFI is working at a basic level, and for bringing 247 up EFI support on a new architecture. 248 249source lib/efi_selftest/Kconfig 250 251config CMD_BOOTMENU 252 bool "bootmenu" 253 select MENU 254 help 255 Add an ANSI terminal boot menu command. 256 257config CMD_ELF 258 bool "bootelf, bootvx" 259 default y 260 help 261 Boot an ELF/vxWorks image from the memory. 262 263config CMD_FDT 264 bool "Flattened Device Tree utility commands" 265 default y 266 depends on OF_LIBFDT 267 help 268 Do FDT related setup before booting into the Operating System. 269 270config CMD_GO 271 bool "go" 272 default y 273 help 274 Start an application at a given address. 275 276config CMD_RUN 277 bool "run" 278 default y 279 help 280 Run the command in the given environment variable. 281 282config CMD_IMI 283 bool "iminfo" 284 default y 285 help 286 Print header information for application image. 287 288config CMD_IMLS 289 bool "imls" 290 help 291 List all images found in flash 292 293config CMD_XIMG 294 bool "imxtract" 295 default y 296 help 297 Extract a part of a multi-image. 298 299config CMD_POWEROFF 300 bool "poweroff" 301 help 302 Poweroff/Shutdown the system 303 304config CMD_SPL 305 bool "spl export - Export boot information for Falcon boot" 306 depends on SPL 307 help 308 Falcon mode allows booting directly from SPL into an Operating 309 System such as Linux, thus skipping U-Boot proper. See 310 doc/README.falcon for full information about how to use this 311 command. 312 313config CMD_SPL_NAND_OFS 314 hex "Offset of OS command line args for Falcon-mode NAND boot" 315 depends on CMD_SPL 316 default 0 317 help 318 This provides the offset of the command line arguments for Linux 319 when booting from NAND in Falcon mode. See doc/README.falcon 320 for full information about how to use this option (and also see 321 board/gateworks/gw_ventana/README for an example). 322 323config CMD_SPL_WRITE_SIZE 324 hex "Size of argument area" 325 depends on CMD_SPL 326 default 0x2000 327 help 328 This provides the size of the command-line argument area in NAND 329 flash used by Falcon-mode boot. See the documentation until CMD_SPL 330 for detail. 331 332config CMD_FITUPD 333 bool "fitImage update command" 334 help 335 Implements the 'fitupd' command, which allows to automatically 336 store software updates present on a TFTP server in NOR Flash 337 338config CMD_THOR_DOWNLOAD 339 bool "thor - TIZEN 'thor' download" 340 help 341 Implements the 'thor' download protocol. This is a way of 342 downloading a software update over USB from an attached host. 343 There is no documentation about this within the U-Boot source code 344 but you should be able to find something on the interwebs. 345 346config CMD_ZBOOT 347 bool "zboot - x86 boot command" 348 help 349 With x86 machines it is common to boot a bzImage file which 350 contains both a kernel and a setup.bin file. The latter includes 351 configuration information from the dark ages which x86 boards still 352 need to pick things out of. 353 354 Consider using FIT in preference to this since it supports directly 355 booting both 32- and 64-bit kernels, as well as secure boot. 356 Documentation is available in doc/uImage.FIT/x86-fit-boot.txt 357 358endmenu 359 360menu "Environment commands" 361 362config CMD_ASKENV 363 bool "ask for env variable" 364 help 365 Ask for environment variable 366 367config CMD_EXPORTENV 368 bool "env export" 369 default y 370 help 371 Export environments. 372 373config CMD_IMPORTENV 374 bool "env import" 375 default y 376 help 377 Import environments. 378 379config CMD_EDITENV 380 bool "editenv" 381 default y 382 help 383 Edit environment variable. 384 385config CMD_GREPENV 386 bool "search env" 387 help 388 Allow for searching environment variables 389 390config CMD_SAVEENV 391 bool "saveenv" 392 default y 393 help 394 Save all environment variables into the compiled-in persistent 395 storage. 396 397config CMD_ENV_EXISTS 398 bool "env exists" 399 default y 400 help 401 Check if a variable is defined in the environment for use in 402 shell scripting. 403 404config CMD_ENV_CALLBACK 405 bool "env callbacks - print callbacks and their associated variables" 406 help 407 Some environment variable have callbacks defined by 408 U_BOOT_ENV_CALLBACK. These are called when the variable changes. 409 For example changing "baudrate" adjust the serial baud rate. This 410 command lists the currently defined callbacks. 411 412config CMD_ENV_FLAGS 413 bool "env flags -print variables that have non-default flags" 414 help 415 Some environment variables have special flags that control their 416 behaviour. For example, serial# can only be written once and cannot 417 be deleted. This command shows the variables that have special 418 flags. 419 420endmenu 421 422menu "Memory commands" 423 424config CMD_BINOP 425 bool "binop" 426 help 427 Compute binary operations (xor, or, and) of byte arrays of arbitrary 428 size from memory and store the result in memory or the environment. 429 430config CMD_CRC32 431 bool "crc32" 432 select HASH 433 default y 434 help 435 Compute CRC32. 436 437config CRC32_VERIFY 438 bool "crc32 -v" 439 depends on CMD_CRC32 440 help 441 Add -v option to verify data against a crc32 checksum. 442 443config CMD_EEPROM 444 bool "eeprom - EEPROM subsystem" 445 help 446 (deprecated, needs conversion to driver model) 447 Provides commands to read and write EEPROM (Electrically Erasable 448 Programmable Read Only Memory) chips that are connected over an 449 I2C bus. 450 451config CMD_EEPROM_LAYOUT 452 bool "Enable layout-aware eeprom commands" 453 depends on CMD_EEPROM 454 help 455 (deprecated, needs conversion to driver model) 456 When enabled, additional eeprom sub-commands become available. 457 458 eeprom print - prints the contents of the eeprom in a human-readable 459 way (eeprom layout fields, and data formatted to be fit for human 460 consumption). 461 462 eeprom update - allows user to update eeprom fields by specifying 463 the field name, and providing the new data in a human readable format 464 (same format as displayed by the eeprom print command). 465 466 Both commands can either auto detect the layout, or be told which 467 layout to use. 468 469 Feature API: 470 __weak int parse_layout_version(char *str) 471 - override to provide your own layout name parsing 472 __weak void __eeprom_layout_assign(struct eeprom_layout *layout, 473 int layout_version); 474 - override to setup the layout metadata based on the version 475 __weak int eeprom_layout_detect(unsigned char *data) 476 - override to provide your own algorithm for detecting layout 477 version 478 eeprom_field.c 479 - contains various printing and updating functions for common 480 types of eeprom fields. Can be used for defining 481 custom layouts. 482 483config EEPROM_LAYOUT_HELP_STRING 484 string "Tells user what layout names are supported" 485 depends on CMD_EEPROM_LAYOUT 486 default "<not defined>" 487 help 488 Help printed with the LAYOUT VERSIONS part of the 'eeprom' 489 command's help. 490 491config LOOPW 492 bool "loopw" 493 help 494 Infinite write loop on address range 495 496config CMD_MD5SUM 497 bool "md5sum" 498 default n 499 select MD5 500 help 501 Compute MD5 checksum. 502 503config MD5SUM_VERIFY 504 bool "md5sum -v" 505 default n 506 depends on CMD_MD5SUM 507 help 508 Add -v option to verify data against an MD5 checksum. 509 510config CMD_MEMINFO 511 bool "meminfo" 512 help 513 Display memory information. 514 515config CMD_MEMORY 516 bool "md, mm, nm, mw, cp, cmp, base, loop" 517 default y 518 help 519 Memory commands. 520 md - memory display 521 mm - memory modify (auto-incrementing address) 522 nm - memory modify (constant address) 523 mw - memory write (fill) 524 cp - memory copy 525 cmp - memory compare 526 base - print or set address offset 527 loop - initialize loop on address range 528 529config CMD_MEMTEST 530 bool "memtest" 531 help 532 Simple RAM read/write test. 533 534if CMD_MEMTEST 535 536config SYS_ALT_MEMTEST 537 bool "Alternative test" 538 help 539 Use a more complete alternative memory test. 540 541endif 542 543config CMD_MX_CYCLIC 544 bool "mdc, mwc" 545 help 546 mdc - memory display cyclic 547 mwc - memory write cyclic 548 549config CMD_SHA1SUM 550 bool "sha1sum" 551 select SHA1 552 help 553 Compute SHA1 checksum. 554 555config SHA1SUM_VERIFY 556 bool "sha1sum -v" 557 depends on CMD_SHA1SUM 558 help 559 Add -v option to verify data against a SHA1 checksum. 560 561config CMD_STRINGS 562 bool "strings - display strings in memory" 563 help 564 This works similarly to the Unix 'strings' command except that it 565 works with a memory range. String of printable characters found 566 within the range are displayed. The minimum number of characters 567 for a sequence to be considered a string can be provided. 568 569endmenu 570 571menu "Compression commands" 572 573config CMD_LZMADEC 574 bool "lzmadec" 575 default y if CMD_BOOTI 576 select LZMA 577 help 578 Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm) 579 image from memory. 580 581config CMD_UNZIP 582 bool "unzip" 583 default y if CMD_BOOTI 584 help 585 Uncompress a zip-compressed memory region. 586 587config CMD_ZIP 588 bool "zip" 589 help 590 Compress a memory region with zlib deflate method. 591 592endmenu 593 594menu "Device access commands" 595 596config CMD_ARMFLASH 597 #depends on FLASH_CFI_DRIVER 598 bool "armflash" 599 help 600 ARM Ltd reference designs flash partition access 601 602config CMD_ADC 603 bool "adc - Access Analog to Digital Converters info and data" 604 select ADC 605 select DM_REGULATOR 606 help 607 Shows ADC device info and permit printing one-shot analog converted 608 data from a named Analog to Digital Converter. 609 610config CMD_ANDROID_AB_SELECT 611 bool "android_ab_select" 612 default n 613 depends on ANDROID_AB 614 help 615 On Android devices with more than one boot slot (multiple copies of 616 the kernel and system images) this provides a command to select which 617 slot should be used to boot from and register the boot attempt. This 618 is used by the new A/B update model where one slot is updated in the 619 background while running from the other slot. 620 621config CMD_BOOT_ANDROID 622 bool "boot_android" 623 default n 624 depends on ANDROID_BOOTLOADER 625 help 626 Performs the Android Bootloader boot flow, loading the appropriate 627 Android image (normal kernel, recovery kernel or "bootloader" mode) 628 and booting it. The boot mode is determined by the contents of the 629 Android Bootloader Message. 630 631config CMD_CLK 632 bool "clk - Show clock frequencies" 633 help 634 (deprecated) 635 Shows clock frequences by calling a sock_clk_dump() hook function. 636 This is depreated in favour of using the CLK uclass and accessing 637 clock values from associated drivers. However currently no command 638 exists for this. 639 640config CMD_DEMO 641 bool "demo - Demonstration commands for driver model" 642 depends on DM 643 help 644 Provides a 'demo' command which can be used to play around with 645 driver model. To use this properly you will need to enable one or 646 both of the demo devices (DM_DEMO_SHAPE and DM_DEMO_SIMPLE). 647 Otherwise you will always get an empty list of devices. The demo 648 devices are defined in the sandbox device tree, so the easiest 649 option is to use sandbox and pass the -d point to sandbox's 650 u-boot.dtb file. 651 652config CMD_DFU 653 bool "dfu" 654 select DFU 655 help 656 Enables the command "dfu" which is used to have U-Boot create a DFU 657 class device via USB. This command requires that the "dfu_alt_info" 658 environment variable be set and define the alt settings to expose to 659 the host. 660 661config CMD_DM 662 bool "dm - Access to driver model information" 663 depends on DM 664 default y 665 help 666 Provides access to driver model data structures and information, 667 such as a list of devices, list of uclasses and the state of each 668 device (e.g. activated). This is not required for operation, but 669 can be useful to see the state of driver model for debugging or 670 interest. 671 672config CMD_FASTBOOT 673 bool "fastboot - Android fastboot support" 674 depends on FASTBOOT 675 help 676 This enables the command "fastboot" which enables the Android 677 fastboot mode for the platform. Fastboot is a protocol for 678 downloading images, flashing and device control used on 679 Android devices. Fastboot requires either the network stack 680 enabled or support for acting as a USB device. 681 682 See doc/README.android-fastboot for more information. 683 684config CMD_FDC 685 bool "fdcboot - Boot from floppy device" 686 help 687 The 'fdtboot' command allows booting an image from a floppy disk. 688 689config CMD_FLASH 690 bool "flinfo, erase, protect" 691 default y 692 help 693 NOR flash support. 694 flinfo - print FLASH memory information 695 erase - FLASH memory 696 protect - enable or disable FLASH write protection 697 698config CMD_FPGA 699 bool "fpga" 700 depends on FPGA 701 default y 702 help 703 FPGA support. 704 705config CMD_FPGA_LOADBP 706 bool "fpga loadbp - load partial bitstream (Xilinx only)" 707 depends on CMD_FPGA 708 help 709 Supports loading an FPGA device from a bitstream buffer containing 710 a partial bitstream. 711 712config CMD_FPGA_LOADFS 713 bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)" 714 depends on CMD_FPGA 715 help 716 Supports loading an FPGA device from a FAT filesystem. 717 718config CMD_FPGA_LOADMK 719 bool "fpga loadmk - load bitstream from image" 720 depends on CMD_FPGA 721 help 722 Supports loading an FPGA device from a image generated by mkimage. 723 724config CMD_FPGA_LOADP 725 bool "fpga loadp - load partial bitstream" 726 depends on CMD_FPGA 727 help 728 Supports loading an FPGA device from a bitstream buffer containing 729 a partial bitstream. 730 731config CMD_FPGA_LOAD_SECURE 732 bool "fpga loads - loads secure bitstreams (Xilinx only)" 733 depends on CMD_FPGA 734 help 735 Enables the fpga loads command which is used to load secure 736 (authenticated or encrypted or both) bitstreams on to FPGA. 737 738config CMD_FPGAD 739 bool "fpgad - dump FPGA registers" 740 help 741 (legacy, needs conversion to driver model) 742 Provides a way to dump FPGA registers by calling the board-specific 743 fpga_get_reg() function. This functions similarly to the 'md' 744 command. 745 746config CMD_FUSE 747 bool "fuse - support for the fuse subssystem" 748 help 749 (deprecated - needs conversion to driver model) 750 This allows reading, sensing, programming or overriding fuses 751 which control the behaviour of the device. The command uses the 752 fuse_...() API. 753 754config CMD_GPIO 755 bool "gpio" 756 help 757 GPIO support. 758 759config CMD_GPT 760 bool "GPT (GUID Partition Table) command" 761 select PARTITION_UUIDS 762 select EFI_PARTITION 763 select HAVE_BLOCK_DEVICE 764 imply RANDOM_UUID 765 help 766 Enable the 'gpt' command to ready and write GPT style partition 767 tables. 768 769config RANDOM_UUID 770 bool "GPT Random UUID generation" 771 select LIB_UUID 772 help 773 Enable the generation of partitions with random UUIDs if none 774 are provided. 775 776config CMD_GPT_RENAME 777 bool "GPT partition renaming commands" 778 depends on CMD_GPT 779 help 780 Enables the 'gpt' command to interchange names on two GPT 781 partitions via the 'gpt swap' command or to rename single 782 partitions via the 'rename' command. 783 784config CMD_IDE 785 bool "ide - Support for IDE drivers" 786 select IDE 787 help 788 Provides an 'ide' command which allows accessing the IDE drive, 789 reseting the IDE interface, printing the partition table and 790 geting device info. It also enables the 'diskboot' command which 791 permits booting from an IDE drive. 792 793config CMD_IO 794 bool "io - Support for performing I/O accesses" 795 help 796 Provides an 'iod' command to display I/O space and an 'iow' command 797 to write values to the I/O space. This can be useful for manually 798 checking the state of devices during boot when debugging device 799 drivers, etc. 800 801config CMD_IOTRACE 802 bool "iotrace - Support for tracing I/O activity" 803 help 804 Provides an 'iotrace' command which supports recording I/O reads and 805 writes in a trace buffer in memory . It also maintains a checksum 806 of the trace records (even if space is exhausted) so that the 807 sequence of I/O accesses can be verified. 808 809 When debugging drivers it is useful to see what I/O accesses were 810 done and in what order. 811 812 Even if the individual accesses are of little interest it can be 813 useful to verify that the access pattern is consistent each time 814 an operation is performed. In this case a checksum can be used to 815 characterise the operation of a driver. The checksum can be compared 816 across different runs of the operation to verify that the driver is 817 working properly. 818 819 In particular, when performing major refactoring of the driver, where 820 the access pattern should not change, the checksum provides assurance 821 that the refactoring work has not broken the driver. 822 823 This works by sneaking into the io.h heder for an architecture and 824 redirecting I/O accesses through iotrace's tracing mechanism. 825 826 For now no commands are provided to examine the trace buffer. The 827 format is fairly simple, so 'md' is a reasonable substitute. 828 829 Note: The checksum feature is only useful for I/O regions where the 830 contents do not change outside of software control. Where this is not 831 suitable you can fall back to manually comparing the addresses. It 832 might be useful to enhance tracing to only checksum the accesses and 833 not the data read/written. 834 835config CMD_I2C 836 bool "i2c" 837 help 838 I2C support. 839 840config CMD_LOADB 841 bool "loadb" 842 default y 843 help 844 Load a binary file over serial line. 845 846config CMD_LOADS 847 bool "loads" 848 default y 849 help 850 Load an S-Record file over serial line 851 852config CMD_LOAD_ANDROID 853 bool "load_android" 854 default n 855 depends on ANDROID_BOOT_IMAGE 856 help 857 Load an Android Boot image from storage. The Android Boot images 858 define the size and kernel address on the header, which are used by 859 this command. 860 861config CMD_MMC 862 bool "mmc" 863 help 864 MMC memory mapped support. 865 866config CMD_MMC_RPMB 867 bool "Enable support for RPMB in the mmc command" 868 depends on CMD_MMC 869 help 870 Enable the commands for reading, writing and programming the 871 key for the Replay Protection Memory Block partition in eMMC. 872 873config CMD_MMC_SWRITE 874 bool "mmc swrite" 875 depends on CMD_MMC && MMC_WRITE 876 select IMAGE_SPARSE 877 help 878 Enable support for the "mmc swrite" command to write Android sparse 879 images to eMMC. 880 881config CMD_NAND 882 bool "nand" 883 default y if NAND_SUNXI 884 help 885 NAND support. 886 887if CMD_NAND 888config CMD_NAND_TRIMFFS 889 bool "nand write.trimffs" 890 default y if ARCH_SUNXI 891 help 892 Allows one to skip empty pages when flashing something on a NAND. 893 894config CMD_NAND_LOCK_UNLOCK 895 bool "nand lock/unlock" 896 help 897 NAND locking support. 898 899config CMD_NAND_TORTURE 900 bool "nand torture" 901 help 902 NAND torture support. 903 904endif # CMD_NAND 905 906config CMD_NVME 907 bool "nvme" 908 depends on NVME 909 default y if NVME 910 help 911 NVM Express device support 912 913config CMD_MMC_SPI 914 bool "mmc_spi - Set up MMC SPI device" 915 help 916 Provides a way to set up an MMC (Multimedia Card) SPI (Serial 917 Peripheral Interface) device. The device provides a means of 918 accessing an MMC device via SPI using a single data line, limited 919 to 20MHz. It is useful since it reduces the amount of protocol code 920 required. 921 922config CMD_ONENAND 923 bool "onenand - access to onenand device" 924 help 925 OneNAND is a brand of NAND ('Not AND' gate) flash which provides 926 various useful features. This command allows reading, writing, 927 and erasing blocks. It allso provides a way to show and change 928 bad blocks, and test the device. 929 930config CMD_PART 931 bool "part" 932 select PARTITION_UUIDS 933 select HAVE_BLOCK_DEVICE 934 help 935 Read and display information about the partition table on 936 various media. 937 938config CMD_PCI 939 bool "pci - Access PCI devices" 940 help 941 Provide access to PCI (Peripheral Interconnect Bus), a type of bus 942 used on some devices to allow the CPU to communicate with its 943 peripherals. Sub-commands allow bus enumeration, displaying and 944 changing configuration space and a few other features. 945 946config CMD_PCMCIA 947 bool "pinit - Set up PCMCIA device" 948 help 949 Provides a means to initialise a PCMCIA (Personal Computer Memory 950 Card International Association) device. This is an old standard from 951 about 1990. These devices are typically removable memory or network 952 cards using a standard 68-pin connector. 953 954config CMD_READ 955 bool "read - Read binary data from a partition" 956 help 957 Provides low-level access to the data in a partition. 958 959config CMD_REMOTEPROC 960 bool "remoteproc" 961 depends on REMOTEPROC 962 help 963 Support for Remote Processor control 964 965config CMD_SATA 966 bool "sata - Access SATA subsystem" 967 select SATA 968 help 969 SATA (Serial Advanced Technology Attachment) is a serial bus 970 standard for connecting to hard drives and other storage devices. 971 This command provides information about attached devices and allows 972 reading, writing and other operations. 973 974 SATA replaces PATA (originally just ATA), which stands for Parallel AT 975 Attachment, where AT refers to an IBM AT (Advanced Technology) 976 computer released in 1984. 977 978config CMD_SAVES 979 bool "saves - Save a file over serial in S-Record format" 980 help 981 Provides a way to save a binary file using the Motorola S-Record 982 format over the serial line. 983 984config CMD_SCSI 985 bool "scsi - Access to SCSI devices" 986 default y if SCSI 987 help 988 This provides a 'scsi' command which provides access to SCSI (Small 989 Computer System Interface) devices. The command provides a way to 990 scan the bus, reset the bus, read and write data and get information 991 about devices. 992 993config CMD_SDRAM 994 bool "sdram - Print SDRAM configuration information" 995 help 996 Provides information about attached SDRAM. This assumed that the 997 SDRAM has an EEPROM with information that can be read using the 998 I2C bus. This is only available on some boards. 999 1000config CMD_SF 1001 bool "sf" 1002 help 1003 SPI Flash support 1004 1005config CMD_SF_TEST 1006 bool "sf test - Allow testing of SPI flash" 1007 help 1008 Provides a way to test that SPI flash is working correctly. The 1009 test is destructive, in that an area of SPI flash must be provided 1010 for the test to use. Performance information is also provided, 1011 measuring the performance of reading, writing and erasing in 1012 Mbps (Million Bits Per Second). This value should approximately 1013 equal the SPI bus speed for a single-bit-wide SPI bus, assuming 1014 everything is working properly. 1015 1016config CMD_SPI 1017 bool "sspi" 1018 help 1019 SPI utility command. 1020 1021config CMD_TSI148 1022 bool "tsi148 - Command to access tsi148 device" 1023 help 1024 This provides various sub-commands to initialise and configure the 1025 Turndra tsi148 device. See the command help for full details. 1026 1027config CMD_UNIVERSE 1028 bool "universe - Command to set up the Turndra Universe controller" 1029 help 1030 This allows setting up the VMEbus provided by this controller. 1031 See the command help for full details. 1032 1033config CMD_USB 1034 bool "usb" 1035 select HAVE_BLOCK_DEVICE 1036 help 1037 USB support. 1038 1039config CMD_USB_SDP 1040 bool "sdp" 1041 select USB_FUNCTION_SDP 1042 help 1043 Enables the command "sdp" which is used to have U-Boot emulating the 1044 Serial Download Protocol (SDP) via USB. 1045config CMD_ROCKUSB 1046 bool "rockusb" 1047 depends on USB_FUNCTION_ROCKUSB 1048 help 1049 Rockusb protocol is widely used by Rockchip SoC based devices. It can 1050 read/write info, image to/from devices. This enable rockusb command 1051 support to communication with rockusb device. for more detail about 1052 this command, please read doc/README.rockusb. 1053 1054config CMD_USB_MASS_STORAGE 1055 bool "UMS usb mass storage" 1056 select USB_FUNCTION_MASS_STORAGE 1057 help 1058 USB mass storage support 1059 1060endmenu 1061 1062 1063menu "Shell scripting commands" 1064 1065config CMD_ECHO 1066 bool "echo" 1067 default y 1068 help 1069 Echo args to console 1070 1071config CMD_ITEST 1072 bool "itest" 1073 default y 1074 help 1075 Return true/false on integer compare. 1076 1077config CMD_SOURCE 1078 bool "source" 1079 default y 1080 help 1081 Run script from memory 1082 1083config CMD_SETEXPR 1084 bool "setexpr" 1085 default y 1086 help 1087 Evaluate boolean and math expressions and store the result in an env 1088 variable. 1089 Also supports loading the value at a memory location into a variable. 1090 If CONFIG_REGEX is enabled, setexpr also supports a gsub function. 1091 1092endmenu 1093 1094if NET 1095 1096menuconfig CMD_NET 1097 bool "Network commands" 1098 default y 1099 1100if CMD_NET 1101 1102config CMD_BOOTP 1103 bool "bootp" 1104 default y 1105 help 1106 bootp - boot image via network using BOOTP/TFTP protocol 1107 1108config CMD_DHCP 1109 bool "dhcp" 1110 depends on CMD_BOOTP 1111 help 1112 Boot image via network using DHCP/TFTP protocol 1113 1114config BOOTP_BOOTPATH 1115 bool "Request & store 'rootpath' from BOOTP/DHCP server" 1116 default y 1117 depends on CMD_BOOTP 1118 help 1119 Even though the config is called BOOTP_BOOTPATH, it stores the 1120 path in the variable 'rootpath'. 1121 1122config BOOTP_DNS 1123 bool "Request & store 'dnsip' from BOOTP/DHCP server" 1124 default y 1125 depends on CMD_BOOTP 1126 help 1127 The primary DNS server is stored as 'dnsip'. If two servers are 1128 returned, you must set BOOTP_DNS2 to store that second server IP 1129 also. 1130 1131config BOOTP_DNS2 1132 bool "Store 'dnsip2' from BOOTP/DHCP server" 1133 depends on BOOTP_DNS 1134 help 1135 If a DHCP client requests the DNS server IP from a DHCP server, 1136 it is possible that more than one DNS serverip is offered to the 1137 client. If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS 1138 server IP will be stored in the additional environment 1139 variable "dnsip2". The first DNS serverip is always 1140 stored in the variable "dnsip", when BOOTP_DNS is defined. 1141 1142config BOOTP_GATEWAY 1143 bool "Request & store 'gatewayip' from BOOTP/DHCP server" 1144 default y 1145 depends on CMD_BOOTP 1146 1147config BOOTP_HOSTNAME 1148 bool "Request & store 'hostname' from BOOTP/DHCP server" 1149 default y 1150 depends on CMD_BOOTP 1151 help 1152 The name may or may not be qualified with the local domain name. 1153 1154config BOOTP_PREFER_SERVERIP 1155 bool "serverip variable takes precedent over DHCP server IP." 1156 depends on CMD_BOOTP 1157 help 1158 By default a BOOTP/DHCP reply will overwrite the 'serverip' variable. 1159 1160 With this option enabled, the 'serverip' variable in the environment 1161 takes precedence over DHCP server IP and will only be set by the DHCP 1162 server if not already set in the environment. 1163 1164config BOOTP_SUBNETMASK 1165 bool "Request & store 'netmask' from BOOTP/DHCP server" 1166 default y 1167 depends on CMD_BOOTP 1168 1169config BOOTP_NTPSERVER 1170 bool "Request & store 'ntpserverip' from BOOTP/DHCP server" 1171 depends on CMD_BOOTP 1172 1173config BOOTP_PXE 1174 bool "Send PXE client arch to BOOTP/DHCP server" 1175 default y 1176 depends on CMD_BOOTP && CMD_PXE 1177 help 1178 Supported for ARM, ARM64, and x86 for now. 1179 1180config BOOTP_PXE_CLIENTARCH 1181 hex 1182 depends on BOOTP_PXE 1183 default 0x16 if ARM64 1184 default 0x15 if ARM 1185 default 0 if X86 1186 1187config BOOTP_VCI_STRING 1188 string 1189 depends on CMD_BOOTP 1190 default "U-Boot.armv7" if CPU_V7A || CPU_V7M || CPU_V7R 1191 default "U-Boot.armv8" if ARM64 1192 default "U-Boot.arm" if ARM 1193 default "U-Boot" 1194 1195config CMD_TFTPBOOT 1196 bool "tftpboot" 1197 default y 1198 help 1199 tftpboot - boot image via network using TFTP protocol 1200 1201config CMD_TFTPPUT 1202 bool "tftp put" 1203 depends on CMD_TFTPBOOT 1204 help 1205 TFTP put command, for uploading files to a server 1206 1207config CMD_TFTPSRV 1208 bool "tftpsrv" 1209 depends on CMD_TFTPBOOT 1210 help 1211 Act as a TFTP server and boot the first received file 1212 1213config NET_TFTP_VARS 1214 bool "Control TFTP timeout and count through environment" 1215 depends on CMD_TFTPBOOT 1216 default y 1217 help 1218 If set, allows controlling the TFTP timeout through the 1219 environment variable tftptimeout, and the TFTP maximum 1220 timeout count through the variable tftptimeoutcountmax. 1221 If unset, timeout and maximum are hard-defined as 1 second 1222 and 10 timouts per TFTP transfer. 1223 1224config CMD_RARP 1225 bool "rarpboot" 1226 help 1227 Boot image via network using RARP/TFTP protocol 1228 1229config CMD_NFS 1230 bool "nfs" 1231 default y 1232 help 1233 Boot image via network using NFS protocol. 1234 1235config CMD_MII 1236 bool "mii" 1237 help 1238 Enable MII utility commands. 1239 1240config CMD_PING 1241 bool "ping" 1242 help 1243 Send ICMP ECHO_REQUEST to network host 1244 1245config CMD_CDP 1246 bool "cdp" 1247 help 1248 Perform CDP network configuration 1249 1250config CMD_SNTP 1251 bool "sntp" 1252 help 1253 Synchronize RTC via network 1254 1255config CMD_DNS 1256 bool "dns" 1257 help 1258 Lookup the IP of a hostname 1259 1260config CMD_LINK_LOCAL 1261 bool "linklocal" 1262 select LIB_RAND 1263 help 1264 Acquire a network IP address using the link-local protocol 1265 1266endif 1267 1268config CMD_ETHSW 1269 bool "ethsw" 1270 help 1271 Allow control of L2 Ethernet switch commands. These are supported 1272 by the vsc9953 Ethernet driver at present. Sub-commands allow 1273 operations such as enabling / disabling a port and 1274 viewing/maintaining the filtering database (FDB) 1275 1276config CMD_PXE 1277 bool "pxe" 1278 select MENU 1279 help 1280 Boot image via network using PXE protocol 1281 1282config CMD_WOL 1283 bool "wol" 1284 help 1285 Wait for wake-on-lan Magic Packet 1286 1287endif 1288 1289menu "Misc commands" 1290 1291config CMD_BMP 1292 bool "Enable 'bmp' command" 1293 depends on LCD || DM_VIDEO || VIDEO 1294 help 1295 This provides a way to obtain information about a BMP-format iamge 1296 and to display it. BMP (which presumably stands for BitMaP) is a 1297 file format defined by Microsoft which supports images of various 1298 depths, formats and compression methods. Headers on the file 1299 determine the formats used. This command can be used by first loading 1300 the image into RAM, then using this command to look at it or display 1301 it. 1302 1303config CMD_BOOTCOUNT 1304 bool "bootcount" 1305 depends on BOOTCOUNT_LIMIT 1306 help 1307 Enable the bootcount command, which allows interrogation and 1308 reset of the bootcounter. 1309 1310config CMD_BSP 1311 bool "Enable board-specific commands" 1312 help 1313 (deprecated: instead, please define a Kconfig option for each command) 1314 1315 Some boards have board-specific commands which are only enabled 1316 during developemnt and need to be turned off for production. This 1317 option provides a way to control this. The commands that are enabled 1318 vary depending on the board. 1319 1320config CMD_BKOPS_ENABLE 1321 bool "mmc bkops enable" 1322 depends on CMD_MMC 1323 default n 1324 help 1325 Enable command for setting manual background operations handshake 1326 on a eMMC device. The feature is optionally available on eMMC devices 1327 conforming to standard >= 4.41. 1328 1329config CMD_BLOCK_CACHE 1330 bool "blkcache - control and stats for block cache" 1331 depends on BLOCK_CACHE 1332 default y if BLOCK_CACHE 1333 help 1334 Enable the blkcache command, which can be used to control the 1335 operation of the cache functions. 1336 This is most useful when fine-tuning the operation of the cache 1337 during development, but also allows the cache to be disabled when 1338 it might hurt performance (e.g. when using the ums command). 1339 1340config CMD_CACHE 1341 bool "icache or dcache" 1342 help 1343 Enable the "icache" and "dcache" commands 1344 1345config CMD_DISPLAY 1346 bool "Enable the 'display' command, for character displays" 1347 help 1348 (this needs porting to driver model) 1349 This enables the 'display' command which allows a string to be 1350 displayed on a simple board-specific display. Implement 1351 display_putc() to use it. 1352 1353config CMD_LED 1354 bool "led" 1355 default y if LED 1356 help 1357 Enable the 'led' command which allows for control of LEDs supported 1358 by the board. The LEDs can be listed with 'led list' and controlled 1359 with led on/off/togle/blink. Any LED drivers can be controlled with 1360 this command, e.g. led_gpio. 1361 1362config CMD_DATE 1363 bool "date" 1364 default y if DM_RTC 1365 help 1366 Enable the 'date' command for getting/setting the time/date in RTC 1367 devices. 1368 1369config CMD_TIME 1370 bool "time" 1371 help 1372 Run commands and summarize execution time. 1373 1374config CMD_GETTIME 1375 bool "gettime - read elapsed time" 1376 help 1377 Enable the 'gettime' command which reads the elapsed time since 1378 U-Boot started running. This shows the time in seconds and 1379 milliseconds. See also the 'bootstage' command which provides more 1380 flexibility for boot timing. 1381 1382# TODO: rename to CMD_SLEEP 1383config CMD_MISC 1384 bool "sleep" 1385 default y 1386 help 1387 Delay execution for some time 1388 1389config CMD_TIMER 1390 bool "timer" 1391 help 1392 Access the system timer. 1393 1394config CMD_SOUND 1395 bool "sound" 1396 depends on SOUND 1397 help 1398 This provides basic access to the U-Boot's sound support. The main 1399 feature is to play a beep. 1400 1401 sound init - set up sound system 1402 sound play - play a sound 1403 1404config CMD_QFW 1405 bool "qfw" 1406 select QFW 1407 help 1408 This provides access to the QEMU firmware interface. The main 1409 feature is to allow easy loading of files passed to qemu-system 1410 via -kernel / -initrd 1411 1412source "cmd/mvebu/Kconfig" 1413 1414config CMD_TERMINAL 1415 bool "terminal - provides a way to attach a serial terminal" 1416 help 1417 Provides a 'cu'-like serial terminal command. This can be used to 1418 access other serial ports from the system console. The terminal 1419 is very simple with no special processing of characters. As with 1420 cu, you can press ~. (tilde followed by period) to exit. 1421 1422config CMD_UUID 1423 bool "uuid, guid - generation of unique IDs" 1424 select LIB_UUID 1425 help 1426 This enables two commands: 1427 1428 uuid - generate random Universally Unique Identifier 1429 guid - generate Globally Unique Identifier based on random UUID 1430 1431 The two commands are very similar except for the endianness of the 1432 output. 1433 1434endmenu 1435 1436source "cmd/ti/Kconfig" 1437 1438config CMD_BOOTSTAGE 1439 bool "Enable the 'bootstage' command" 1440 depends on BOOTSTAGE 1441 help 1442 Add a 'bootstage' command which supports printing a report 1443 and un/stashing of bootstage data. 1444 1445menu "Power commands" 1446config CMD_PMIC 1447 bool "Enable Driver Model PMIC command" 1448 depends on DM_PMIC 1449 help 1450 This is the pmic command, based on a driver model pmic's API. 1451 Command features are unchanged: 1452 - list - list pmic devices 1453 - pmic dev <id> - show or [set] operating pmic device (NEW) 1454 - pmic dump - dump registers 1455 - pmic read address - read byte of register at address 1456 - pmic write address - write byte to register at address 1457 The only one change for this command is 'dev' subcommand. 1458 1459config CMD_REGULATOR 1460 bool "Enable Driver Model REGULATOR command" 1461 depends on DM_REGULATOR 1462 help 1463 This command is based on driver model regulator's API. 1464 User interface features: 1465 - list - list regulator devices 1466 - regulator dev <id> - show or [set] operating regulator device 1467 - regulator info - print constraints info 1468 - regulator status - print operating status 1469 - regulator value <val] <-f> - print/[set] voltage value [uV] 1470 - regulator current <val> - print/[set] current value [uA] 1471 - regulator mode <id> - print/[set] operating mode id 1472 - regulator enable - enable the regulator output 1473 - regulator disable - disable the regulator output 1474 1475 The '-f' (force) option can be used for set the value which exceeds 1476 the limits, which are found in device-tree and are kept in regulator's 1477 uclass platdata structure. 1478 1479endmenu 1480 1481menu "Security commands" 1482config CMD_AES 1483 bool "Enable the 'aes' command" 1484 select AES 1485 help 1486 This provides a means to encrypt and decrypt data using the AES 1487 (Advanced Encryption Standard). This algorithm uses a symetric key 1488 and is widely used as a streaming cipher. Different key lengths are 1489 supported by the algorithm but this command only supports 128 bits 1490 at present. 1491 1492config CMD_BLOB 1493 bool "Enable the 'blob' command" 1494 help 1495 This is used with the Freescale secure boot mechanism. 1496 1497 Freescale's SEC block has built-in Blob Protocol which provides 1498 a method for protecting user-defined data across system power 1499 cycles. SEC block protects data in a data structure called a Blob, 1500 which provides both confidentiality and integrity protection. 1501 1502 Encapsulating data as a blob 1503 Each time that the Blob Protocol is used to protect data, a 1504 different randomly generated key is used to encrypt the data. 1505 This random key is itself encrypted using a key which is derived 1506 from SoC's non-volatile secret key and a 16 bit Key identifier. 1507 The resulting encrypted key along with encrypted data is called a 1508 blob. The non-volatile secure key is available for use only during 1509 secure boot. 1510 1511 During decapsulation, the reverse process is performed to get back 1512 the original data. 1513 1514 Sub-commands: 1515 blob enc - encapsulating data as a cryptgraphic blob 1516 blob dec - decapsulating cryptgraphic blob to get the data 1517 1518 Syntax: 1519 1520 blob enc src dst len km 1521 1522 Encapsulate and create blob of data $len bytes long 1523 at address $src and store the result at address $dst. 1524 $km is the 16 byte key modifier is also required for 1525 generation/use as key for cryptographic operation. Key 1526 modifier should be 16 byte long. 1527 1528 blob dec src dst len km 1529 1530 Decapsulate the blob of data at address $src and 1531 store result of $len byte at addr $dst. 1532 $km is the 16 byte key modifier is also required for 1533 generation/use as key for cryptographic operation. Key 1534 modifier should be 16 byte long. 1535 1536config CMD_HASH 1537 bool "Support 'hash' command" 1538 select HASH 1539 help 1540 This provides a way to hash data in memory using various supported 1541 algorithms (such as SHA1, MD5, CRC32). The computed digest can be 1542 saved to memory or to an environment variable. It is also possible 1543 to verify a hash against data in memory. 1544 1545config CMD_HVC 1546 bool "Support the 'hvc' command" 1547 depends on ARM_SMCCC 1548 help 1549 Allows issuing Hypervisor Calls (HVCs). Mostly useful for 1550 development and testing. 1551 1552config CMD_SMC 1553 bool "Support the 'smc' command" 1554 depends on ARM_SMCCC 1555 help 1556 Allows issuing Secure Monitor Calls (SMCs). Mostly useful for 1557 development and testing. 1558 1559config HASH_VERIFY 1560 bool "hash -v" 1561 depends on CMD_HASH 1562 help 1563 Add -v option to verify data against a hash. 1564 1565config CMD_TPM_V1 1566 bool 1567 1568config CMD_TPM_V2 1569 bool 1570 1571config CMD_TPM 1572 bool "Enable the 'tpm' command" 1573 depends on TPM_V1 || TPM_V2 1574 select CMD_TPM_V1 if TPM_V1 1575 select CMD_TPM_V2 if TPM_V2 1576 help 1577 This provides a means to talk to a TPM from the command line. A wide 1578 range of commands if provided - see 'tpm help' for details. The 1579 command requires a suitable TPM on your board and the correct driver 1580 must be enabled. 1581 1582if CMD_TPM 1583 1584config CMD_TPM_TEST 1585 bool "Enable the 'tpm test' command" 1586 depends on TPM_V1 1587 help 1588 This provides a a series of tests to confirm that the TPMv1.x is 1589 working correctly. The tests cover initialisation, non-volatile RAM, 1590 extend, global lock and checking that timing is within expectations. 1591 The tests pass correctly on Infineon TPMs but may need to be adjusted 1592 for other devices. 1593 1594endif 1595 1596endmenu 1597 1598menu "Firmware commands" 1599config CMD_CROS_EC 1600 bool "Enable crosec command" 1601 depends on CROS_EC 1602 default y 1603 help 1604 Enable command-line access to the Chrome OS EC (Embedded 1605 Controller). This provides the 'crosec' command which has 1606 a number of sub-commands for performing EC tasks such as 1607 updating its flash, accessing a small saved context area 1608 and talking to the I2C bus behind the EC (if there is one). 1609endmenu 1610 1611menu "Filesystem commands" 1612config CMD_BTRFS 1613 bool "Enable the 'btrsubvol' command" 1614 select FS_BTRFS 1615 help 1616 This enables the 'btrsubvol' command to list subvolumes 1617 of a BTRFS filesystem. There are no special commands for 1618 listing BTRFS directories or loading BTRFS files - this 1619 can be done by the generic 'fs' commands (see CMD_FS_GENERIC) 1620 when BTRFS is enabled (see FS_BTRFS). 1621 1622config CMD_CBFS 1623 bool "Enable the 'cbfs' command" 1624 depends on FS_CBFS 1625 help 1626 Define this to enable support for reading from a Coreboot 1627 filesystem. This is a ROM-based filesystem used for accessing files 1628 on systems that use coreboot as the first boot-loader and then load 1629 U-Boot to actually boot the Operating System. Available commands are 1630 cbfsinit, cbfsinfo, cbfsls and cbfsload. 1631 1632config CMD_CRAMFS 1633 bool "Enable the 'cramfs' command" 1634 depends on FS_CRAMFS 1635 help 1636 This provides commands for dealing with CRAMFS (Compressed ROM 1637 filesystem). CRAMFS is useful when space is tight since files are 1638 compressed. Two commands are provided: 1639 1640 cramfsls - lists files in a cramfs image 1641 cramfsload - loads a file from a cramfs image 1642 1643config CMD_EXT2 1644 bool "ext2 command support" 1645 select FS_EXT4 1646 help 1647 Enables EXT2 FS command 1648 1649config CMD_EXT4 1650 bool "ext4 command support" 1651 select FS_EXT4 1652 help 1653 Enables EXT4 FS command 1654 1655config CMD_EXT4_WRITE 1656 depends on CMD_EXT4 1657 bool "ext4 write command support" 1658 select EXT4_WRITE 1659 help 1660 Enables EXT4 FS write command 1661 1662config CMD_FAT 1663 bool "FAT command support" 1664 select FS_FAT 1665 help 1666 Support for the FAT fs 1667 1668config CMD_FS_GENERIC 1669 bool "filesystem commands" 1670 help 1671 Enables filesystem commands (e.g. load, ls) that work for multiple 1672 fs types. 1673 1674config CMD_FS_UUID 1675 bool "fsuuid command" 1676 help 1677 Enables fsuuid command for filesystem UUID. 1678 1679config CMD_JFFS2 1680 bool "jffs2 command" 1681 select FS_JFFS2 1682 help 1683 Enables commands to support the JFFS2 (Journalling Flash File System 1684 version 2) filesystem. This enables fsload, ls and fsinfo which 1685 provide the ability to load files, list directories and obtain 1686 filesystem information. 1687 1688config CMD_MTDPARTS 1689 bool "MTD partition support" 1690 help 1691 MTD partition support 1692 1693config MTDIDS_DEFAULT 1694 string "Default MTD IDs" 1695 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH 1696 help 1697 Defines a default MTD IDs list for use with MTD partitions in the 1698 Linux MTD command line partitions format. 1699 1700config MTDPARTS_DEFAULT 1701 string "Default MTD partition scheme" 1702 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH 1703 help 1704 Defines a default MTD partitioning scheme in the Linux MTD command 1705 line partitions format 1706 1707config CMD_MTDPARTS_SPREAD 1708 bool "Padd partition size to take account of bad blocks" 1709 depends on CMD_MTDPARTS 1710 help 1711 This enables the 'spread' sub-command of the mtdparts command. 1712 This command will modify the existing mtdparts variable by increasing 1713 the size of the partitions such that 1) each partition's net size is 1714 at least as large as the size specified in the mtdparts variable and 1715 2) each partition starts on a good block. 1716 1717config CMD_REISER 1718 bool "reiser - Access to reiserfs filesystems" 1719 help 1720 This provides two commands which operate on a resierfs filesystem, 1721 commonly used some years ago: 1722 1723 reiserls - list files 1724 reiserload - load a file 1725 1726config CMD_YAFFS2 1727 bool "yaffs2 - Access of YAFFS2 filesystem" 1728 depends on YAFFS2 1729 default y 1730 help 1731 This provides commands for accessing a YAFFS2 filesystem. Yet 1732 Another Flash Filesystem 2 is a filesystem designed specifically 1733 for NAND flash. It incorporates bad-block management and ensures 1734 that device writes are sequential regardless of filesystem 1735 activity. 1736 1737config CMD_ZFS 1738 bool "zfs - Access of ZFS filesystem" 1739 help 1740 This provides commands to accessing a ZFS filesystem, commonly used 1741 on Solaris systems. Two sub-commands are provided: 1742 1743 zfsls - list files in a directory 1744 zfsload - load a file 1745 1746 See doc/README.zfs for more details. 1747 1748endmenu 1749 1750menu "Debug commands" 1751 1752config CMD_BEDBUG 1753 bool "bedbug" 1754 help 1755 The bedbug (emBEDded deBUGger) command provides debugging features 1756 for some PowerPC processors. For details please see the 1757 docuemntation in doc/README.beddbug 1758 1759config CMD_DIAG 1760 bool "diag - Board diagnostics" 1761 help 1762 This command provides access to board diagnostic tests. These are 1763 called Power-on Self Tests (POST). The command allows listing of 1764 available tests and running either all the tests, or specific tests 1765 identified by name. 1766 1767config CMD_IRQ 1768 bool "irq - Show information about interrupts" 1769 depends on !ARM && !MIPS && !SH 1770 help 1771 This enables two commands: 1772 1773 interrupts - enable or disable interrupts 1774 irqinfo - print device-specific interrupt information 1775 1776config CMD_KGDB 1777 bool "kgdb - Allow debugging of U-Boot with gdb" 1778 help 1779 This enables a 'kgdb' command which allows gdb to connect to U-Boot 1780 over a serial link for debugging purposes. This allows 1781 single-stepping, inspecting variables, etc. This is supported only 1782 on PowerPC at present. 1783 1784config CMD_LOG 1785 bool "log - Generation, control and access to logging" 1786 select LOG 1787 help 1788 This provides access to logging features. It allows the output of 1789 log data to be controlled to a limited extent (setting up the default 1790 maximum log level for emitting of records). It also provides access 1791 to a command used for testing the log system. 1792 1793config CMD_TRACE 1794 bool "trace - Support tracing of function calls and timing" 1795 help 1796 Enables a command to control using of function tracing within 1797 U-Boot. This allows recording of call traces including timing 1798 information. The command can write data to memory for exporting 1799 for analsys (e.g. using bootchart). See doc/README.trace for full 1800 details. 1801 1802config CMD_AVB 1803 bool "avb - Android Verified Boot 2.0 operations" 1804 depends on LIBAVB 1805 default n 1806 help 1807 Enables a "avb" command to perform verification of partitions using 1808 Android Verified Boot 2.0 functionality. It includes such subcommands: 1809 avb init - initialize avb2 subsystem 1810 avb read_rb - read rollback index 1811 avb write_rb - write rollback index 1812 avb is_unlocked - check device lock state 1813 avb get_uuid - read and print uuid of a partition 1814 avb read_part - read data from partition 1815 avb read_part_hex - read data from partition and output to stdout 1816 avb write_part - write data to partition 1817 avb verify - run full verification chain 1818endmenu 1819 1820config CMD_UBI 1821 tristate "Enable UBI - Unsorted block images commands" 1822 select CRC32 1823 select MTD_UBI 1824 select CMD_MTDPARTS 1825 default y if NAND_SUNXI 1826 help 1827 UBI is a software layer above MTD layer which admits use of LVM-like 1828 logical volumes on top of MTD devices, hides some complexities of 1829 flash chips like wear and bad blocks and provides some other useful 1830 capabilities. Please, consult the MTD web site for more details 1831 (www.linux-mtd.infradead.org). Activate this option if you want 1832 to use U-Boot UBI commands. 1833 1834config CMD_UBIFS 1835 tristate "Enable UBIFS - Unsorted block images filesystem commands" 1836 depends on CMD_UBI 1837 select CRC32 1838 select LZO 1839 default y if CMD_UBI 1840 help 1841 UBIFS is a file system for flash devices which works on top of UBI. 1842 1843endmenu 1844