1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2009 4 * Marvell Semiconductor <www.marvell.com> 5 * Prafulla Wadaskar <prafulla@marvell.com> 6 * 7 * (C) Copyright 2009 8 * Stefan Roese, DENX Software Engineering, sr@denx.de. 9 * 10 * (C) Copyright 2010-2011 11 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 12 */ 13 14 /* 15 * for linking errors see 16 * http://lists.denx.de/pipermail/u-boot/2009-July/057350.html 17 */ 18 19 #ifndef _CONFIG_KM_ARM_H 20 #define _CONFIG_KM_ARM_H 21 22 /* 23 * High Level Configuration Options (easy to change) 24 */ 25 #define CONFIG_MARVELL 26 #define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */ 27 #define CONFIG_KW88F6281 /* SOC Name */ 28 29 #define CONFIG_MACH_TYPE MACH_TYPE_KM_KIRKWOOD 30 31 #define CONFIG_NAND_ECC_BCH 32 33 /* include common defines/options for all Keymile boards */ 34 #include "keymile-common.h" 35 36 /* SPI NOR Flash default params, used by sf commands */ 37 #define CONFIG_SF_DEFAULT_SPEED 8100000 38 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 39 40 #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR 41 #define CONFIG_ENV_SPI_BUS 0 42 #define CONFIG_ENV_SPI_CS 0 43 #define CONFIG_ENV_SPI_MAX_HZ 8100000 44 #define CONFIG_ENV_SPI_MODE SPI_MODE_3 45 #endif 46 47 /* Reserve 4 MB for malloc */ 48 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 49 50 #include "asm/arch/config.h" 51 52 #define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ 53 #define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ 54 #define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ 55 56 /* pseudo-non volatile RAM [hex] */ 57 #define CONFIG_KM_PNVRAM 0x80000 58 /* physical RAM MTD size [hex] */ 59 #define CONFIG_KM_PHRAM 0x17F000 60 61 #define CONFIG_KM_CRAMFS_ADDR 0x2400000 62 #define CONFIG_KM_KERNEL_ADDR 0x2000000 /* 3098KBytes */ 63 #define CONFIG_KM_FDT_ADDR 0x23E0000 /* 128KBytes */ 64 65 /* architecture specific default bootargs */ 66 #define CONFIG_KM_DEF_BOOT_ARGS_CPU \ 67 "bootcountaddr=${bootcountaddr} ${mtdparts}" \ 68 " boardid=0x${IVM_BoardId} hwkey=0x${IVM_HWKey}" 69 70 #define CONFIG_KM_DEF_ENV_CPU \ 71 "u-boot="CONFIG_HOSTNAME "/u-boot.kwb\0" \ 72 CONFIG_KM_UPDATE_UBOOT \ 73 "set_fdthigh=setenv fdt_high ${kernelmem}\0" \ 74 "checkfdt=" \ 75 "if cramfsls fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb; " \ 76 "then true; else setenv cramfsloadfdt true; " \ 77 "setenv boot bootm ${load_addr_r}; " \ 78 "echo No FDT found, booting with the kernel " \ 79 "appended one; fi\0" \ 80 "" 81 82 #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 83 #define CONFIG_MISC_INIT_R 84 85 /* 86 * NS16550 Configuration 87 */ 88 #define CONFIG_SYS_NS16550_SERIAL 89 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 90 #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK 91 #define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE 92 #define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE 93 94 /* 95 * Serial Port configuration 96 * The following definitions let you select what serial you want to use 97 * for your console driver. 98 */ 99 100 /* 101 * For booting Linux, the board info and command line data 102 * have to be in the first 8 MB of memory, since this is 103 * the maximum mapped by the Linux kernel during initialization. 104 */ 105 #define CONFIG_BOOTMAPSZ (8 << 20) /* Initial Memmap for Linux */ 106 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 107 #define CONFIG_INITRD_TAG /* enable INITRD tag */ 108 #define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */ 109 110 /* 111 * NAND Flash configuration 112 */ 113 #define CONFIG_SYS_MAX_NAND_DEVICE 1 114 115 #define BOOTFLASH_START 0x0 116 117 /* Kirkwood has two serial IF */ 118 #if (CONFIG_CONS_INDEX == 2) 119 #define CONFIG_KM_CONSOLE_TTY "ttyS1" 120 #else 121 #define CONFIG_KM_CONSOLE_TTY "ttyS0" 122 #endif 123 124 /* 125 * Other required minimal configurations 126 */ 127 #define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ 128 #define CONFIG_NR_DRAM_BANKS 4 129 #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ 130 131 /* 132 * Ethernet Driver configuration 133 */ 134 #define CONFIG_NETCONSOLE /* include NetConsole support */ 135 #define CONFIG_MII /* expose smi ove miiphy interface */ 136 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ 137 #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ 138 #define CONFIG_PHY_BASE_ADR 0 139 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ 140 #define CONFIG_KM_COMMON_ETH_INIT /* standard km ethernet_present for piggy */ 141 142 /* 143 * I2C related stuff 144 */ 145 #undef CONFIG_I2C_MVTWSI 146 #define CONFIG_SYS_I2C 147 #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ 148 #define CONFIG_SYS_I2C_INIT_BOARD 149 150 #define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */ 151 #define CONFIG_SYS_NUM_I2C_BUSES 6 152 #define CONFIG_SYS_I2C_MAX_HOPS 1 153 #define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ 154 {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ 155 {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ 156 {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \ 157 {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \ 158 {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \ 159 } 160 161 #ifndef __ASSEMBLY__ 162 #include <asm/arch/gpio.h> 163 extern void __set_direction(unsigned pin, int high); 164 void set_sda(int state); 165 void set_scl(int state); 166 int get_sda(void); 167 int get_scl(void); 168 #define KM_KIRKWOOD_SDA_PIN 8 169 #define KM_KIRKWOOD_SCL_PIN 9 170 #define KM_KIRKWOOD_SOFT_I2C_GPIOS 0x0300 171 #define KM_KIRKWOOD_ENV_WP 38 172 173 #define I2C_ACTIVE __set_direction(KM_KIRKWOOD_SDA_PIN, 0) 174 #define I2C_TRISTATE __set_direction(KM_KIRKWOOD_SDA_PIN, 1) 175 #define I2C_READ (kw_gpio_get_value(KM_KIRKWOOD_SDA_PIN) ? 1 : 0) 176 #define I2C_SDA(bit) kw_gpio_set_value(KM_KIRKWOOD_SDA_PIN, bit) 177 #define I2C_SCL(bit) kw_gpio_set_value(KM_KIRKWOOD_SCL_PIN, bit) 178 #endif 179 180 #define I2C_DELAY udelay(1) 181 #define I2C_SOFT_DECLARATIONS 182 183 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x0 184 #define CONFIG_SYS_I2C_SOFT_SPEED 100000 185 186 /* EEprom support 24C128, 24C256 valid for environment eeprom */ 187 #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE 188 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 Byte write page */ 189 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 190 191 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 192 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 193 194 /* 195 * Environment variables configurations 196 */ 197 #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR 198 #define CONFIG_ENV_OFFSET 0xc0000 /* no bracets! */ 199 #define CONFIG_ENV_SIZE 0x02000 /* Size of Environment */ 200 #define CONFIG_ENV_SECT_SIZE 0x10000 201 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 202 CONFIG_ENV_SECT_SIZE) 203 #define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */ 204 #else 205 #define CONFIG_SYS_DEF_EEPROM_ADDR 0x50 206 #define CONFIG_ENV_EEPROM_IS_ON_I2C 207 #define CONFIG_SYS_EEPROM_WREN 208 #define CONFIG_ENV_OFFSET 0x0 /* no bracets! */ 209 #define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET) 210 #define CONFIG_I2C_ENV_EEPROM_BUS 5 /* I2C2 (Mux-Port 5) */ 211 #define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */ 212 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 213 #endif 214 215 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 216 217 218 /* SPI bus claim MPP configuration */ 219 #define CONFIG_SYS_KW_SPI_MPP 0x0 220 221 #define FLASH_GPIO_PIN 0x00010000 222 #define KM_FLASH_GPIO_PIN 16 223 224 #define CONFIG_KM_UPDATE_UBOOT \ 225 "update=" \ 226 "sf probe 0;sf erase 0 +${filesize};" \ 227 "sf write ${load_addr_r} 0 ${filesize};\0" 228 229 #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR 230 #define CONFIG_KM_NEW_ENV \ 231 "newenv=sf probe 0;" \ 232 "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \ 233 __stringify(CONFIG_ENV_TOTAL_SIZE)"\0" 234 #else 235 #define CONFIG_KM_NEW_ENV \ 236 "newenv=setenv addr 0x100000 && " \ 237 "i2c dev " __stringify(CONFIG_I2C_ENV_EEPROM_BUS) "; " \ 238 "mw.b ${addr} 0 4 && " \ 239 "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \ 240 " ${addr} " __stringify(CONFIG_ENV_OFFSET) " 4 && " \ 241 "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \ 242 " ${addr} " __stringify(CONFIG_ENV_OFFSET_REDUND) " 4\0" 243 #endif 244 245 #ifndef CONFIG_KM_BOARD_EXTRA_ENV 246 #define CONFIG_KM_BOARD_EXTRA_ENV "" 247 #endif 248 249 /* 250 * Default environment variables 251 */ 252 #define CONFIG_EXTRA_ENV_SETTINGS \ 253 CONFIG_KM_BOARD_EXTRA_ENV \ 254 CONFIG_KM_DEF_ENV \ 255 CONFIG_KM_NEW_ENV \ 256 "arch=arm\0" \ 257 "" 258 259 #if !defined(CONFIG_MTD_NOR_FLASH) 260 #undef CONFIG_FLASH_CFI_MTD 261 #undef CONFIG_JFFS2_CMDLINE 262 #endif 263 264 /* additions for new relocation code, must be added to all boards */ 265 #define CONFIG_SYS_SDRAM_BASE 0x00000000 266 /* Do early setups now in board_init_f() */ 267 268 /* 269 * resereved pram area at the end of memroy [hex] 270 * 8Mbytes for switch + 4Kbytes for bootcount 271 */ 272 #define CONFIG_KM_RESERVED_PRAM 0x801000 273 /* address for the bootcount (taken from end of RAM) */ 274 #define BOOTCOUNT_ADDR (CONFIG_KM_RESERVED_PRAM) 275 276 /* enable POST tests */ 277 #define CONFIG_POST (CONFIG_SYS_POST_MEM_REGIONS) 278 #define CONFIG_POST_SKIP_ENV_FLAGS 279 #define CONFIG_POST_EXTERNAL_WORD_FUNCS 280 281 /* we do the whole PCIe FPGA config stuff here */ 282 283 #endif /* _CONFIG_KM_ARM_H */ 284