1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2009 4 * Marvell Semiconductor <www.marvell.com> 5 * Written-by: Prafulla Wadaskar <prafulla@marvell.com> 6 */ 7 8 #ifndef _MVEBU_CPU_H 9 #define _MVEBU_CPU_H 10 11 #include <asm/system.h> 12 13 #ifndef __ASSEMBLY__ 14 15 #define MVEBU_REG_PCIE_DEVID (MVEBU_REG_PCIE_BASE + 0x00) 16 #define MVEBU_REG_PCIE_REVID (MVEBU_REG_PCIE_BASE + 0x08) 17 18 enum memory_bank { 19 BANK0, 20 BANK1, 21 BANK2, 22 BANK3 23 }; 24 25 enum cpu_winen { 26 CPU_WIN_DISABLE, 27 CPU_WIN_ENABLE 28 }; 29 30 enum cpu_target { 31 CPU_TARGET_DRAM = 0x0, 32 CPU_TARGET_DEVICEBUS_BOOTROM_SPI = 0x1, 33 CPU_TARGET_ETH23 = 0x3, 34 CPU_TARGET_PCIE02 = 0x4, 35 CPU_TARGET_ETH01 = 0x7, 36 CPU_TARGET_PCIE13 = 0x8, 37 CPU_TARGET_SASRAM = 0x9, 38 CPU_TARGET_SATA01 = 0xa, /* A38X */ 39 CPU_TARGET_NAND = 0xd, 40 CPU_TARGET_SATA23_DFX = 0xe, /* A38X */ 41 }; 42 43 enum cpu_attrib { 44 CPU_ATTR_SASRAM = 0x01, 45 CPU_ATTR_DRAM_CS0 = 0x0e, 46 CPU_ATTR_DRAM_CS1 = 0x0d, 47 CPU_ATTR_DRAM_CS2 = 0x0b, 48 CPU_ATTR_DRAM_CS3 = 0x07, 49 CPU_ATTR_NANDFLASH = 0x2f, 50 CPU_ATTR_SPIFLASH = 0x1e, 51 CPU_ATTR_SPI0_CS0 = 0x1e, 52 CPU_ATTR_SPI0_CS1 = 0x5e, 53 CPU_ATTR_SPI1_CS2 = 0x9a, 54 CPU_ATTR_BOOTROM = 0x1d, 55 CPU_ATTR_PCIE_IO = 0xe0, 56 CPU_ATTR_PCIE_MEM = 0xe8, 57 CPU_ATTR_DEV_CS0 = 0x3e, 58 CPU_ATTR_DEV_CS1 = 0x3d, 59 CPU_ATTR_DEV_CS2 = 0x3b, 60 CPU_ATTR_DEV_CS3 = 0x37, 61 }; 62 63 enum { 64 MVEBU_SOC_AXP, 65 MVEBU_SOC_A375, 66 MVEBU_SOC_A38X, 67 MVEBU_SOC_MSYS, 68 MVEBU_SOC_UNKNOWN, 69 }; 70 71 /* 72 * Default Device Address MAP BAR values 73 */ 74 #define MBUS_PCI_MEM_BASE 0xE8000000 75 #define MBUS_PCI_MEM_SIZE (128 << 20) 76 #define MBUS_PCI_IO_BASE 0xF1100000 77 #define MBUS_PCI_IO_SIZE (64 << 10) 78 #define MBUS_SPI_BASE 0xF4000000 79 #define MBUS_SPI_SIZE (8 << 20) 80 #define MBUS_BOOTROM_BASE 0xF8000000 81 #define MBUS_BOOTROM_SIZE (8 << 20) 82 83 struct mbus_win { 84 u32 base; 85 u32 size; 86 u8 target; 87 u8 attr; 88 }; 89 90 /* 91 * System registers 92 * Ref: Datasheet sec:A.28 93 */ 94 struct mvebu_system_registers { 95 #if defined(CONFIG_ARMADA_375) 96 u8 pad1[0x54]; 97 #else 98 u8 pad1[0x60]; 99 #endif 100 u32 rstoutn_mask; /* 0x60 */ 101 u32 sys_soft_rst; /* 0x64 */ 102 }; 103 104 /* 105 * GPIO Registers 106 * Ref: Datasheet sec:A.19 107 */ 108 struct kwgpio_registers { 109 u32 dout; 110 u32 oe; 111 u32 blink_en; 112 u32 din_pol; 113 u32 din; 114 u32 irq_cause; 115 u32 irq_mask; 116 u32 irq_level; 117 }; 118 119 struct sar_freq_modes { 120 u8 val; 121 u8 ffc; /* Fabric Frequency Configuration */ 122 u32 p_clk; 123 u32 nb_clk; 124 u32 d_clk; 125 }; 126 127 /* Needed for dynamic (board-specific) mbus configuration */ 128 extern struct mvebu_mbus_state mbus_state; 129 130 /* 131 * functions 132 */ 133 unsigned int mvebu_sdram_bar(enum memory_bank bank); 134 unsigned int mvebu_sdram_bs(enum memory_bank bank); 135 void mvebu_sdram_size_adjust(enum memory_bank bank); 136 int mvebu_mbus_probe(struct mbus_win windows[], int count); 137 int mvebu_soc_family(void); 138 u32 mvebu_get_nand_clock(void); 139 140 void return_to_bootrom(void); 141 142 int mv_sdh_init(unsigned long regbase, u32 max_clk, u32 min_clk, u32 quirks); 143 144 void get_sar_freq(struct sar_freq_modes *sar_freq); 145 146 /* 147 * Highspeed SERDES PHY config init, ported from bin_hdr 148 * to mainline U-Boot 149 */ 150 int serdes_phy_config(void); 151 152 /* 153 * DDR3 init / training code ported from Marvell bin_hdr. Now 154 * available in mainline U-Boot in: 155 * drivers/ddr/marvell 156 */ 157 int ddr3_init(void); 158 159 struct mvebu_lcd_info { 160 u32 fb_base; 161 int x_res; 162 int y_res; 163 int x_fp; /* frontporch */ 164 int y_fp; 165 int x_bp; /* backporch */ 166 int y_bp; 167 }; 168 169 int mvebu_lcd_register_init(struct mvebu_lcd_info *lcd_info); 170 171 /* 172 * get_ref_clk 173 * 174 * return: reference clock in MHz (25 or 40) 175 */ 176 u32 get_ref_clk(void); 177 178 #endif /* __ASSEMBLY__ */ 179 #endif /* _MVEBU_CPU_H */ 180