1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2017 NXP 4 */ 5 6 #ifndef __LS1012A2G5RDB_H__ 7 #define __LS1012A2G5RDB_H__ 8 9 #include "ls1012a_common.h" 10 11 /* DDR */ 12 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 13 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 14 #define CONFIG_NR_DRAM_BANKS 2 15 #define CONFIG_SYS_SDRAM_SIZE 0x40000000 16 #define CONFIG_CMD_MEMINFO 17 #define CONFIG_SYS_MEMTEST_START 0x80000000 18 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 19 20 /* MMC */ 21 #ifdef CONFIG_MMC 22 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 23 #endif 24 25 /* SATA */ 26 #define CONFIG_LIBATA 27 #define CONFIG_SCSI_AHCI 28 #define CONFIG_SCSI_AHCI_PLAT 29 30 #define CONFIG_SYS_SATA AHCI_BASE_ADDR 31 32 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 33 #define CONFIG_SYS_SCSI_MAX_LUN 1 34 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 35 CONFIG_SYS_SCSI_MAX_LUN) 36 #define CONFIG_CMD_MEMINFO 37 #define CONFIG_SYS_MEMTEST_START 0x80000000 38 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 39 40 #undef CONFIG_EXTRA_ENV_SETTINGS 41 #define CONFIG_EXTRA_ENV_SETTINGS \ 42 "verify=no\0" \ 43 "fdt_high=0xffffffffffffffff\0" \ 44 "initrd_high=0xffffffffffffffff\0" \ 45 "fdt_addr=0x00f00000\0" \ 46 "kernel_addr=0x01000000\0" \ 47 "kernelheader_addr=0x800000\0" \ 48 "scriptaddr=0x80000000\0" \ 49 "scripthdraddr=0x80080000\0" \ 50 "fdtheader_addr_r=0x80100000\0" \ 51 "kernelheader_addr_r=0x80200000\0" \ 52 "kernel_addr_r=0x81000000\0" \ 53 "fdt_addr_r=0x90000000\0" \ 54 "load_addr=0xa0000000\0" \ 55 "kernel_size=0x2800000\0" \ 56 "kernelheader_size=0x40000\0" \ 57 "console=ttyS0,115200\0" \ 58 BOOTENV \ 59 "boot_scripts=ls1012ardb_boot.scr\0" \ 60 "boot_script_hdr=hdr_ls1012ardb_bs.out\0" \ 61 "scan_dev_for_boot_part=" \ 62 "part list ${devtype} ${devnum} devplist; " \ 63 "env exists devplist || setenv devplist 1; " \ 64 "for distro_bootpart in ${devplist}; do " \ 65 "if fstype ${devtype} " \ 66 "${devnum}:${distro_bootpart} " \ 67 "bootfstype; then " \ 68 "run scan_dev_for_boot; " \ 69 "fi; " \ 70 "done\0" \ 71 "scan_dev_for_boot=" \ 72 "echo Scanning ${devtype} " \ 73 "${devnum}:${distro_bootpart}...; " \ 74 "for prefix in ${boot_prefixes}; do " \ 75 "run scan_dev_for_scripts; " \ 76 "done;" \ 77 "\0" \ 78 "boot_a_script=" \ 79 "load ${devtype} ${devnum}:${distro_bootpart} " \ 80 "${scriptaddr} ${prefix}${script}; " \ 81 "env exists secureboot && load ${devtype} " \ 82 "${devnum}:${distro_bootpart} " \ 83 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 84 "&& esbc_validate ${scripthdraddr};" \ 85 "source ${scriptaddr}\0" \ 86 "installer=load mmc 0:2 $load_addr " \ 87 "/flex_installer_arm64.itb; " \ 88 "bootm $load_addr#$board\0" \ 89 "qspi_bootcmd=echo Trying load from qspi..;" \ 90 "sf probe && sf read $load_addr " \ 91 "$kernel_addr $kernel_size; env exists secureboot " \ 92 "&& sf read $kernelheader_addr_r $kernelheader_addr " \ 93 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \ 94 "bootm $load_addr#$board\0" 95 96 #undef CONFIG_BOOTCOMMAND 97 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 98 #define CONFIG_BOOTCOMMAND "pfe stop;run distro_bootcmd; run qspi_bootcmd; " \ 99 "env exists secureboot && esbc_halt;" 100 #endif 101 102 #define DEFAULT_PFE_MDIO_NAME "PFE_MDIO" 103 #define DEFAULT_PFE_MDIO1_NAME "PFE_MDIO1" 104 105 #include <asm/fsl_secure_boot.h> 106 107 #endif /* __LS1012A2G5RDB_H__ */ 108