Searched refs:BMCR_ANENABLE (Results 1 – 24 of 24) sorted by relevance
| /external/u-boot/drivers/net/ |
| D | mcfmii.c | 247 if ((status & BMCR_ANENABLE) == BMCR_ANENABLE) { in __mii_init()
|
| D | ftmac110.c | 152 if (!(bmcr & BMCR_ANENABLE) || (bmsr & BMSR_ANEGCOMPLETE)) in ftmac110_phyqry()
159 if (!(bmcr & BMCR_ANENABLE)) in ftmac110_phyqry()
165 if ((bmcr & BMCR_ANENABLE) && (bmsr & BMSR_ANEGCOMPLETE)) { in ftmac110_phyqry()
|
| D | ax88180.c | 116 ax88180_mdio_write (dev, MII_BMCR, (BMCR_RESET | BMCR_ANENABLE)); in ax88180_phy_reset()
353 if (bmcr_val & BMCR_ANENABLE) { in ax88180_media_config()
|
| D | smc911x.c | 90 smc911x_eth_phy_write(dev, 1, MII_BMCR, BMCR_ANENABLE | in smc911x_phy_configure()
|
| D | dnet.c | 224 dnet_mdio_write(dnet, MII_BMCR, (BMCR_ANENABLE in dnet_phy_reset()
|
| D | ftgmac100.c | 148 MII_BMCR, (BMCR_ANENABLE | BMCR_ANRESTART)); in ftgmac100_phy_reset()
|
| D | at91_emac.c | 197 (BMCR_ANENABLE | BMCR_ANRESTART)); in at91emac_phy_reset()
|
| D | davinci_emac.c | 329 val = tmp | BMCR_FULLDPLX | BMCR_ANENABLE | in gen_auto_negotiate()
|
| D | ag7xxx.c | 720 BMCR_ANENABLE | BMCR_RESET); in ag933x_phy_setup_reset_set()
|
| D | macb.c | 451 macb_mdio_write(macb, MII_BMCR, (BMCR_ANENABLE in macb_phy_reset()
|
| D | fec_mxc.c | 215 BMCR_ANENABLE | BMCR_ANRESTART); in miiphy_restart_aneg()
|
| /external/u-boot/common/ |
| D | miiphyutil.c | 425 if (bmcr & BMCR_ANENABLE) { in miiphy_speed()
488 if (bmcr & BMCR_ANENABLE) { in miiphy_duplex()
|
| /external/u-boot/drivers/net/phy/ |
| D | et1011c.c | 34 BMCR_ANENABLE); in et1011c_config()
|
| D | ti.c | 243 (BMCR_ANENABLE | BMCR_FULLDPLX | BMCR_SPEED1000)); in dp83867_config()
|
| D | phy.c | 160 ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); in genphy_restart_aneg()
200 if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE)) in genphy_config_aneg()
|
| /external/kernel-headers/original/uapi/linux/ |
| D | mii.h | 48 #define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ macro
|
| D | mdio.h | 87 #define MDIO_AN_CTRL1_ENABLE BMCR_ANENABLE
|
| /external/u-boot/drivers/qe/ |
| D | uec_phy.c | 262 BMCR_SPEED1000 | BMCR_ANENABLE); in genmii_setup_forced()
298 ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); in genmii_restart_aneg()
900 uec_phy_write(mii_info, MII_BMCR, status | BMCR_ANENABLE); in marvell_phy_interface_mode()
|
| /external/u-boot/include/linux/ |
| D | mii.h | 43 #define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ macro
|
| D | mdio.h | 82 #define MDIO_AN_CTRL1_ENABLE BMCR_ANENABLE
|
| /external/u-boot/drivers/usb/eth/ |
| D | mcs7830.c | 324 flg |= BMCR_ANENABLE; in mcs7830_set_autoneg()
|
| D | asix.c | 326 if (bmcr & BMCR_ANENABLE) { in mii_nway_restart()
|
| D | smsc95xx.c | 337 if (bmcr & BMCR_ANENABLE) { in mii_nway_restart()
|
| D | r8152.c | 934 bmcr = BMCR_ANENABLE | BMCR_ANRESTART; in rtl8152_set_speed()
|